SLVSBO3A December   2013  – December 2015 TPS657120

PRODUCTION DATA.  

  1. 1 Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2 Revision History
  3. 3 Terminal Configuration and Functions
    1. 3.1 Pin Attributes
  4. 4 Specifications
    1. 4.1  Absolute Maximum Ratings
    2. 4.2  ESD Ratings
    3. 4.3  Recommended Operating Conditions
    4. 4.4  Thermal Information
    5. 4.5  Electrical Characteristics: General Functions
    6. 4.6  Electrical Characteristics: DCDC1 and DCDC2
    7. 4.7  Electrical Characteristics: DCDC3
    8. 4.8  Electrical Characteristics: RF-LDOs
    9. 4.9  Electrical Characteristics: Digital Inputs, Digital Outputs
    10. 4.10 Electrical Characteristics: Thermal Shutdown, Undervoltage Lockout
    11. 4.11 Electrical Characteristics: RFFE Timing Parameters
    12. 4.12 Typical Characteristics
  5. 5 Detailed Description
    1. 5.1 Overview
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1  Default Settings
      2. 5.3.2  Linear Regulators
        1. 5.3.2.1 Low Quiescent Current (Eco) Mode
        2. 5.3.2.2 Output Discharge
        3. 5.3.2.3 LDO Enable
        4. 5.3.2.4 LDO Voltage Range
        5. 5.3.2.5 LDO Power Good Comparator
      3. 5.3.3  Step-down Converters DCDC1 and DCDC2
      4. 5.3.4  Power Save Mode
      5. 5.3.5  Dynamic Voltage Positioning (Optional)
      6. 5.3.6  Soft Start / Enable
      7. 5.3.7  Dynamic Voltage Scaling (DVS) for DCDC1, DCDC2 and DCDC3
      8. 5.3.8  100% Duty Cycle Low Dropout Operation
      9. 5.3.9  180° Out-of-Phase Operation
      10. 5.3.10 Undervoltage Lockout for DCDC1, DCDC2, DCDC3, LDO1 and LDO2
      11. 5.3.11 Output Voltage Discharge
      12. 5.3.12 Short-Circuit Protection
      13. 5.3.13 Output Voltage Monitoring
      14. 5.3.14 Step-Down Converter and LDO Enable; pins CLK_REQ1 and CLK_REQ2
      15. 5.3.15 Step-Down Converter DCDC3
      16. 5.3.16 DCDC3_SEL Control
        1. 5.3.16.1 DCDC3_SEL Control - Voltage Mapping Option
        2. 5.3.16.2 DCDC3_SEL Control - Mapping the Enable Signal for the Negative Current Limit of DCDC3 to DCDC3_SEL; Additional Option for Rev 1.1 and Higher Only
      17. 5.3.17 Bypass Switch
      18. 5.3.18 DCDC3 Output Voltage Ramp Support
      19. 5.3.19 VCON Decoder
      20. 5.3.20 Thermal Monitoring and Shutdown
      21. 5.3.21 GPIOs
      22. 5.3.22 nRESET Input ; ADR_SELECT Input
      23. 5.3.23 Power State Machine
      24. 5.3.24 Implementation of Internal Power-Up and Power-Down Sequencing
      25. 5.3.25 VDDIO Voltage for Push-pull Output Stages / Interface
      26. 5.3.26 TPS657120 On Off Operation
        1. 5.3.26.1 TPS657120 Power-Up
        2. 5.3.26.2 TPS657120 PWR_REQ Driving DCDC1, DCDC2 and LDO1
      27. 5.3.27 MIPI RFFE Interface
        1. 5.3.27.1 MIPI RFFE Write Cycle
        2. 5.3.27.2 MIPI RFFE Read Cycle
    4. 5.4 Device Functional Modes
    5. 5.5 Register Maps
  6. 6 Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Typical Application
      1. 6.2.1 Design Requirements
      2. 6.2.2 Detailed Design Procedure
        1. 6.2.2.1 Output Filter Design (Inductor and Output Capacitor)
          1. 6.2.2.1.1 Inductor Selection
          2. 6.2.2.1.2 Output Capacitor Selection
          3. 6.2.2.1.3 Input Capacitor / Output Capacitor Selection
          4. 6.2.2.1.4 Voltage Change on DCDC1, DCDC2 and DCDC3
      3. 6.2.3 Application Curve
  7. 7 Power Supply Recommendations
  8. 8 Layout
    1. 8.1 Layout Guidelines
    2. 8.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Community Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  10. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7 Power Supply Recommendations

The power supply decoupling and bulk capacitors are shown in the application drawing.