SWCS095L August   2013  – February 2019 TPS659038-Q1 , TPS659039-Q1

PRODUCTION DATA.  

  1. 1 Device Summary
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Simplified Block Diagram
  2. 2 Revision History
  3. 3 Device Comparison
  4. 4 Pin Configuration and Functions
    1. 4.1 Pin Functions
      1.      Pin Functions
    2. 4.2 Device Ball Mapping – 13 × 13 nFBGA, 169 Balls, 0,8-mm Pitch
    3. 4.3 Signal Descriptions
  5. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Latch Up Rating
    6. 5.6  Electrical Characteristics: LDO Regulator
    7. 5.7  Electrical Characteristics: Dual-Phase (SMPS12 and SMPS45) and Triple-Phase (SMPS123 and SMPS457) Regulators
    8. 5.8  Electrical Characteristics: Stand-Alone Regulators (SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9)
    9. 5.9  Electrical Characteristics: Reference Generator (Bandgap)
    10. 5.10 Electrical Characteristics: 16-MHz Crystal Oscillator, 32-kHz RC Oscillator, and Output Buffers
    11. 5.11 Electrical Characteristics: DC-DC Clock Sync
    12. 5.12 Electrical Characteristics: 12-Bit Sigma-Delta ADC
    13. 5.13 Electrical Characteristics: Thermal Monitoring and Shutdown
    14. 5.14 Electrical Characteristics: System Control Thresholds
    15. 5.15 Electrical Characteristics: Current Consumption
    16. 5.16 Electrical Characteristics: Digital Input Signal Parameters
    17. 5.17 Electrical Characteristics: Digital Output Signal Parameters
    18. 5.18 Electrical Characteristics: I/O Pullup and Pulldown Resistance
    19. 5.19 I2C Interface Timing Requirements
    20. 5.20 SPI Timing Requirements
    21. 5.21 Typical Characteristics
  6. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagrams
    3. 6.3 Feature Description
      1. 6.3.1  Power Management
      2. 6.3.2  Power Resources (Step-Down and Step-Up SMPS Regulators, LDOs)
        1. 6.3.2.1 Step-Down Regulators
          1. 6.3.2.1.1 Sync Clock Functionality
          2. 6.3.2.1.2 Output Voltage and Mode Selection
          3. 6.3.2.1.3 Current Monitoring and Short Circuit Detection
          4. 6.3.2.1.4 POWERGOOD
          5. 6.3.2.1.5 DVS-Capable Regulators
          6. 6.3.2.1.6 Non DVS-Capable Regulators
          7. 6.3.2.1.7 Step-Down Converters SMPS12 and SMPS123
            1.         a. Dual-Phase SMPS and Stand-Alone SMPS
            2.         b. Triple Phase SMPS
          8. 6.3.2.1.8 Step-Down Converter SMPS45 and SMPS457
          9. 6.3.2.1.9 Step-Down Converters SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9
        2. 6.3.2.2 LDOs – Low Dropout Regulators
          1. 6.3.2.2.1 LDOVANA
          2. 6.3.2.2.2 LDOVRTC
          3. 6.3.2.2.3 LDO Bypass (LDO9)
          4. 6.3.2.2.4 LDOUSB
          5. 6.3.2.2.5 Other LDOs
      3. 6.3.3  Long-Press Key Detection
      4. 6.3.4  RTC
        1. 6.3.4.1 General Description
        2. 6.3.4.2 Time Calendar Registers
          1. 6.3.4.2.1 TC Registers Read Access
          2. 6.3.4.2.2 TC Registers Write Access
        3. 6.3.4.3 RTC Alarm
        4. 6.3.4.4 RTC Interrupts
        5. 6.3.4.5 RTC 32-kHz Oscillator Drift Compensation
      5. 6.3.5  GPADC – 12-Bit Sigma-Delta ADC
        1. 6.3.5.1 Asynchronous Conversion Request (SW)
        2. 6.3.5.2 Periodic Conversion Request (AUTO)
        3. 6.3.5.3 Calibration
      6. 6.3.6  General-Purpose I/Os (GPIO Terminals)
        1. 6.3.6.1 REGEN Output
      7. 6.3.7  Thermal Monitoring
        1. 6.3.7.1 Hot-Die Function (HD)
        2. 6.3.7.2 Thermal Shutdown (TS)
        3. 6.3.7.3 Temperature Monitoring With External NTC Resistor or Diode
      8. 6.3.8  Interrupts
      9. 6.3.9  Control Interfaces
        1. 6.3.9.1 I2C Interfaces
          1. 6.3.9.1.1 I2C Implementation
          2. 6.3.9.1.2 F/S Mode Protocol
          3. 6.3.9.1.3 HS Mode Protocol
        2. 6.3.9.2 SPI Interface
          1. 6.3.9.2.1 SPI Modes
          2. 6.3.9.2.2 SPI Protocol
      10. 6.3.10 Device Identification
    4. 6.4 Device Functional Modes
      1. 6.4.1  Embedded Power Controller
      2. 6.4.2  State Transition Requests
        1. 6.4.2.1 ON Requests
        2. 6.4.2.2 OFF Requests
        3. 6.4.2.3 SLEEP and WAKE Requests
      3. 6.4.3  Power Sequences
      4. 6.4.4  Start Up Timing and RESET_OUT Generation
      5. 6.4.5  Power On Acknowledge
        1. 6.4.5.1 POWERHOLD Mode
        2. 6.4.5.2 AUTODEVON Mode
      6. 6.4.6  BOOT Configuration
        1. 6.4.6.1 Boot Terminal Selection
      7. 6.4.7  Reset Levels
      8. 6.4.8  Warm Reset
      9. 6.4.9  RESET_IN
      10. 6.4.10 Watchdog Timer (WDT)
      11. 6.4.11 System Voltage Monitoring
        1. 6.4.11.1 Generating a POR
  7. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1  Recommended External Components
        2. 7.2.2.2  SMPS Input Capacitors
        3. 7.2.2.3  SMPS Output Capacitors
        4. 7.2.2.4  SMPS Inductors
        5. 7.2.2.5  LDO Input Capacitors
        6. 7.2.2.6  LDO Output Capacitors
        7. 7.2.2.7  VCC1
          1. 7.2.2.7.1 Meeting the Power Down Sequence
          2. 7.2.2.7.2 Maintaining Sufficient Input Voltage
        8. 7.2.2.8  VIO_IN
        9. 7.2.2.9  16-MHz Crystal
        10. 7.2.2.10 GPADC
      3. 7.2.3 Application Curves
  8. 8 Power Supply Recommendations
  9. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Device Nomenclature
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Related Links
    4. 10.4 Receiving Notification of Documentation Updates
    5. 10.5 Community Resources
    6. 10.6 Trademarks
    7. 10.7 Electrostatic Discharge Caution
    8. 10.8 Glossary
  11. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Package Materials Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • ZWS|169
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.3.2.1.5 DVS-Capable Regulators

The step-down converters SMPS12 or SMPS123, SMPS45 or SMPS457, SMPS6, and SMPS8 are DVS-capable and have some additional parameters for control. The slew rate of the output voltage during voltage level change is fixed at 2.5 mV/µs. The control for two different voltage levels (ROOF and FLOOR) with the NSLEEP and ENABLE1 signals is available. When the ROOF_FLOOR control is not used, two different voltage levels can be selected with the CMD bit in the SMPSx_FORCE register.

  • The output voltage slew rate for achieving new output voltage value is fixed at 2.5 mV/μs.
  • The NSLEEP and ENABLE1 terminals can be used for roof-floor control of SMPS. For roof-floor operation sets the SMPSx_CTRL.ROOF_FLOOR_EN register, and assign SMPS to NSLEEP and ENABLE1 in the NSLEEP_SMPS_ASSIGN and ENABLE1_SMPS_ASSIGN registers. When the controlling terminal is active, the SMPS output value is defined by the SMPSx_VOLTAGE register. When the controlling terminal is not active, the SMPS output value is defined by the SMPSx_FORCE register.
  • Set the second value for the output voltage with the SMPSx_FORCE.VSEL register. A value of 0x0 disables the SMPS (OFF).
  • Select which register, SMPSx_VOLTAGE or SMPSx_FORCE, to use with the SMPSx_FORCE.CMD bit. The default is the voltage setting of SMPSx_VOLTAGE. For the CMD bit to work, ensure that SMPSx_CTRL.ROOF_FLOOR_EN = 0.

Figure 6-5 shows the SMPS controls for DVS.

TPS659038-Q1 TPS659039-Q1 DVS_SMPS_Controls_SWCS095.gifFigure 6-5 DVS – SMPS Controls