SLVSDM6C October   2016  – August 2021 TPS65983B

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Power Supply Requirements and Characteristics
    6. 7.6  Power Supervisor Characteristics
    7. 7.7  Power Consumption Characteristics
    8. 7.8  Cable Detection Characteristics
    9. 7.9  USB-PD Baseband Signal Requirements and Characteristics
    10. 7.10 USB-PD TX Driver Voltage Adjustment Parameter (1)
    11. 7.11 Port Power Switch Characteristics
    12. 7.12 Port Data Multiplexer Switching and Timing Characteristics
    13. 7.13 Port Data Multiplexer Clamp Characteristics
    14. 7.14 Port Data Multiplexer SBU Detection Requirements
    15. 7.15 Port Data Multiplexer Signal Monitoring Pullup and Pulldown Characteristics
    16. 7.16 Port Data Multiplexer USB Endpoint Requirements and Characteristics
    17. 7.17 Port Data Multiplexer BC1.2 Detection Requirements and Characteristics
    18. 7.18 Analog-to-Digital Converter (ADC) Characteristics
    19. 7.19 Input/Output (I/O) Requirements and Characteristics
    20. 7.20 I2C Slave Requirements and Characteristics
    21. 7.21 SPI Controller Characteristics
    22. 7.22 Single-Wire Debugger (SWD) Timing Requirements
    23. 7.23 BUSPOWERZ Configuration Requirements
    24. 7.24 HPD Timing Requirements and Characteristics
    25. 7.25 Thermal Shutdown Characteristics
    26. 7.26 Oscillator Requirements and Characteristics
    27. 7.27 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  USB-PD Physical Layer
        1. 9.3.1.1 USB-PD Encoding and Signaling
        2. 9.3.1.2 USB-PD Bi-Phase Marked Coding
        3. 9.3.1.3 USB-PD Transmit (TX) and Receive (Rx) Masks
        4. 9.3.1.4 USB-PD BMC Transmitter
        5. 9.3.1.5 USB-PD BMC Receiver
      2. 9.3.2  Cable Plug and Orientation Detection
        1. 9.3.2.1 Configured as a DFP
        2. 9.3.2.2 Configured as a UFP
        3. 9.3.2.3 Fast Role Swap Signaling
        4. 9.3.2.4 Dead-Battery or No-Battery Support
      3. 9.3.3  Port Power Switches
        1. 9.3.3.1  5V Power Delivery
        2. 9.3.3.2  5V Power Switch as a Source
        3. 9.3.3.3  PP_5V0 Current Sense
        4. 9.3.3.4  PP_5V0 Current Limit
        5. 9.3.3.5  Internal HV Power Delivery
        6. 9.3.3.6  Internal HV Power Switch as a Source
        7. 9.3.3.7  Internal HV Power Switch as a Sink
        8. 9.3.3.8  Internal HV Power Switch Current Sense
        9. 9.3.3.9  Internal HV Power Switch Current Limit
        10. 9.3.3.10 External HV Power Delivery
        11. 9.3.3.11 External HV Power Switch as a Source with RSENSE
        12. 9.3.3.12 External HV Power Switch as a Sink with RSENSE
        13. 9.3.3.13 External HV Power Switch as a Sink without RSENSE
        14. 9.3.3.14 External Current Sense
        15. 9.3.3.15 External Current Limit
        16. 9.3.3.16 Soft Start
        17. 9.3.3.17 BUSPOWERZ
        18. 9.3.3.18 Voltage Transitions on VBUS through Port Power Switches
        19. 9.3.3.19 HV Transition to PP_RV0 Pull-Down on VBUS
        20. 9.3.3.20 VBUS Transition to VSAVE0V
        21. 9.3.3.21 C_CC1 and C_CC2 Power Configuration and Power Delivery
        22. 9.3.3.22 PP_CABLE to C_CC1 and C_CC2 Switch Architecture
        23. 9.3.3.23 PP_CABLE to C_CC1 and C_CC2 Current Limit
      4. 9.3.4  USB Type-C Port Data Multiplexer
        1. 9.3.4.1  USB Top and Bottom Ports
        2. 9.3.4.2  Multiplexer Connection Orientation
        3. 9.3.4.3  Digital Crossbar Multiplexer
        4. 9.3.4.4  SBU Crossbar Multiplexer
        5. 9.3.4.5  Signal Monitoring and Pullup and Pulldown
        6. 9.3.4.6  Port Multiplexer Clamp
        7. 9.3.4.7  USB2.0 Low-Speed Endpoint
        8. 9.3.4.8  Battery Charger (BC1.2) Detection Block
        9. 9.3.4.9  BC1.2 Data Contact Detect
        10. 9.3.4.10 BC1.2 Primary and Secondary Detection
      5. 9.3.5  Power Management
        1. 9.3.5.1 Power-On and Supervisory Functions
        2. 9.3.5.2 Supply Switch-Over
        3. 9.3.5.3 RESETZ and MRESET
      6. 9.3.6  Digital Core
      7. 9.3.7  USB-PD BMC Modem Interface
      8. 9.3.8  System Glue Logic
      9. 9.3.9  Power Reset Congrol Module (PRCM)
      10. 9.3.10 Interrupt Monitor
      11. 9.3.11 ADC Sense
      12. 9.3.12 UART
      13. 9.3.13 I2C Slave
      14. 9.3.14 SPI Controller
      15. 9.3.15 Single-Wire Debugger Interface
      16. 9.3.16 DisplayPort HPD Timers
      17. 9.3.17 ADC
        1. 9.3.17.1 ADC Divider Ratios
        2. 9.3.17.2 ADC Operating Modes
        3. 9.3.17.3 Single Channel Readout
        4. 9.3.17.4 Round Robin Automatic Readout
        5. 9.3.17.5 One Time Automatic Readout
      18. 9.3.18 I/O Buffers
        1. 9.3.18.1 IOBUF_GPIOLS and IOBUF_GPIOLSI2C
        2. 9.3.18.2 IOBUF_OD
        3. 9.3.18.3 IOBUF_UTX
        4. 9.3.18.4 IOBUF_URX
        5. 9.3.18.5 IOBUF_PORT
        6. 9.3.18.6 IOBUF_I2C
        7. 9.3.18.7 IOBUF_GPIOHSPI
        8. 9.3.18.8 IOBUF_GPIOHSSWD
      19. 9.3.19 Thermal Shutdown
      20. 9.3.20 Oscillators
    4. 9.4 Device Functional Modes
      1. 9.4.1 Boot Code
      2. 9.4.2 Initialization
      3. 9.4.3 I2C Configuration
      4. 9.4.4 Dead-Battery Condition
      5. 9.4.5 Application Code
      6. 9.4.6 Flash Memory Read
      7. 9.4.7 Invalid Flash Memory
      8. 9.4.8 UART Download
        1. 9.4.8.1 Primary TPS65983B Flash Master and Secondary Port
    5. 9.5 Programming
      1. 9.5.1 SPI Controller Interface
      2. 9.5.2 I2C Slave Interface
        1. 9.5.2.1 I2C Interface Description
        2. 9.5.2.2 I2C Clock Stretching
        3. 9.5.2.3 I2C Address Setting
        4. 9.5.2.4 Unique Address Interface
        5. 9.5.2.5 I2C Pin Address Setting
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Fully-Featured USB Type-C and PD Charger Application
        1. 10.2.1.1 Design Requirements
          1. 10.2.1.1.1 External FET Path Components (PP_EXT and RSENSE)
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 TPS65983B External Flash
          2. 10.2.1.2.2 I2C (I2C), Debug Control (DEBUG_CTL), and Single-Wire De-bugger (SWD) Resistors
          3. 10.2.1.2.3 Oscillator (R_OSC) Resistor
          4. 10.2.1.2.4 VBUS Capacitor and Ferrite Bead
          5. 10.2.1.2.5 Soft Start (SS) Capacitor
          6. 10.2.1.2.6 USB Top (C_USB_T), USB Bottom (C_USB_B), and Sideband-Use (SBU) Connections
          7. 10.2.1.2.7 Port Power Switch (PP_EXT, PP_HV, PP_5V0, and PP_CABLE) Capacitors
          8. 10.2.1.2.8 Cable Connection (CCn) Capacitors and RPD_Gn Connections
          9. 10.2.1.2.9 LDO_3V3, LDO_1V8A, LDO_1V8D, LDO_BMC, VOUT_3V3, VIN_3V3, and VDDIO
        3. 10.2.1.3 Application Curve
      2. 10.2.2 Dual-Port Notebook Application Supporting USB PD Charging and DisplayPort
        1. 10.2.2.1 Design Requirements
          1. 10.2.2.1.1 Source Power Delivery Profiles for Type-C Ports
          2. 10.2.2.1.2 Sink Power Delivery Profile for Type-C Ports
        2. 10.2.2.2 Detailed Design Procedure
          1. 10.2.2.2.1 TPS65983B and System Controller Interaction
          2. 10.2.2.2.2 HD3SS460 Control and DisplayPort Configuration
          3. 10.2.2.2.3 9.3.2.3 DC Barrel Jack and Type-C PD Charging
          4. 10.2.2.2.4 TPS65983B Dead Battery Support Primary and Secondary Port
          5. 10.2.2.2.5 Debugging Methods
        3. 10.2.2.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 3.3 V Power
      1. 11.1.1 1VIN_3V3 Input Switch
      2. 11.1.2 VOUT_3V3 Output Switch
      3. 11.1.3 VBUS 3.3 V LDO
    2. 11.2 1.8 V Core Power
      1. 11.2.1 1.8 V Digital LDO
      2. 11.2.2 1.8 V Analog LDO
    3. 11.3 VDDIO
      1. 11.3.1 Recommended Supply Load Capacitance
      2. 11.3.2 Schottky for Current Surge Protection
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1  TPS65983B Recommended Footprints
        1. 12.1.1.1 Standard TPS65983B Footprint (Circular Pads)
      2. 12.1.2  Alternate TPS65983B Footprint (Oval Pads)
      3. 12.1.3  Top TPS65983B Placement and Bottom Component Placement and Layout
      4. 12.1.4  Oval Pad Footprint Layout and Placement
      5. 12.1.5  Component Placement
      6. 12.1.6  Designs Rules and Guidance
      7. 12.1.7  Routing PP_HV, PP_EXT, PP_5V0, and VBUS
      8. 12.1.8  Routing Top and Bottom Passive Components
      9. 12.1.9  Void Via Placement
      10. 12.1.10 Top Layer Routing
      11. 12.1.11 Inner Signal Layer Routing
      12. 12.1.12 Bottom Layer Routing
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Development Support
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Support Resources
    5. 13.5 Trademarks
    6. 13.6 Electrostatic Discharge Caution
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.19 Input/Output (I/O) Requirements and Characteristics

Recommended operating conditions; TA = –10 to +85°C unless otherwise noted
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SPI
SPI_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
SPI_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
SPI_HYS Input hysteresis voltage LDO_3V3 = 3.3 V 0.2 V
SPI_ILKG Leakage current Output is Hi-Z, VIN = 0 to LDO_3V3  –1 1 μA
SPI_VOH SPI output high voltage IO = –8 mA, LDO_3V3=3.3 V 2.9 V
IO =  –15 mA, LDO_3V3=3.3 V 2.5
SPI_VOL SPI output low voltage IO = 10 mA 0.4 V
IO = 20 mA 0.8
SWDIO
SWDIO_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
SWDIO_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
SWDIO_HYS Input Hysteresis Voltage LDO_3V3 = 3.3 V 0.2 V
SWDIO_ILKG Leakage current Output is Hi-Z, VIN = 0 to LDO_3V3  –1 1 μA
SWDIO_VOH Output high voltage IO =  –8 mA, LDO_3V3 = 3.3 V 2.9 V
IO =  –15 mA, LDO_3V3 = 3.3 V 2.5
SWDIO_VOL Output low voltage IO = 10 mA 0.4 V
IO = 20 mA 0.8
SWDIO_RPU Pullup resistance 2.8 4 5.2 kΩ
SWDIO_TOS SWDIO output skew to falling edge SWDCLK  –5 5 ns
SWDIO_TIS Input setup time required between SWDIO and rising edge of SWCLK 6 ns
SWDIO_TIH Input hold time required between SWDIO and rising edge of SWCLK 1 ns
SWDCLK
SWDCL_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
SWDCL_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
SWDCL_THI SWDIOCLK HIGH period 0.05 500 μs
SWDCL_TLO SWDIOCLK LOW period 0.05 500 μs
SWDCL_HYS Input hysteresis voltage LDO_3V3 = 3.3 V 0.2  V
SWDCL_RPU Pullup resistance 2.8 4 5.2 kΩ
GPIO, MRESET, RESETZ, BUSPOWERZ
GPIO_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
VDDIO = 1.8 V 1.25
GPIO_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
VDDIO = 1.8 V 0.63
GPIO_HYS Input hysteresis Voltage LDO_3V3 = 3.3 V 0.2 V
VDDIO = 1.8 V 0.09
GPIO_ILKG I/O leakage current INPUT = 0 V to VDD  –1 1 μA
GPIO_RPU Pullup resistance Pullup enabled  50 100 150 kΩ
DEBUG_CRTL1/2 pullup resistance Pullup enabled 2.5 5 7.5 kΩ
GPIO_RPD Pulldown resistance (DEBUG_CRTL1/2 have no pulldown resistance path) Pulldown enabled 50  100 150 kΩ
GPIO_DG Digital input path deglitch 20 ns
GPIO_VOH GPIO output high voltage IO = –2 mA, LDO_3V3 = 3.3 V 2.9 V
IO = –2 mA, VDDIO = 1.8 V 1.35
GPIO_VOL GPIO output low voltage IO = 2 mA, LDO_3V3 = 3.3 V 0.4 V
IO = 2 mA, VDDIO = 1.8 V 0.45
HRESET
HRESET_VIH High-level input voltage 1.25 V
HRESET_VIL Low-level input voltage 0.63 V
HRESET_HYS Input hysteresis Voltage .09 V
HRESET_ILKG I/O leakage current INPUT = 0 V to LDO_1V8D  –1 1 μA
HRESET_THIGH HRESET minimum high time to assert a reset condition. 2.0 ms
HRESET_TLOW HRESET minimum low time to deassert a reset condition. 2.0
UART_RX/TX, LSX_P2R/R2P
UARTRX_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
VDDDIO = 1.8 V 1.25
UARTRX_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
VDDIO = 1.8 V 0.63
UARTRX_HYS Input hysteresis voltage LDO_3V3 = 3.3 V 0.2  V
VDDIO = 1.8 V 0.09
UARTTX_VOH GPIO output high voltage IO = –2 mA, LDO_3V3 = 3.3 V 2.9 V
IO = –2 mA, VDDIO = 1.8 V 1.35
UARTTX_VOL GPIO output low voltage IO = 2 mA, LDO_3V3 = 3.3 V 0.4 V
IO = 2 mA, VDDIO = 1.8 V 0.45
UARTTX_RO Output impedance, TX channel  LDO_3V3 = 3.3 V  35 70 115 Ω
UARTTX_TRTF Rise and fall time, TX channel 10%–90%, CL = 20 pF 1 40 ns
UART_FMAX Maximum UART baud rate 1.1 Mbps
I2C_IRQ1Z, I2C_IRQ2Z
OD_VOL Low level output voltage IOL = 2 mA 0.4 V
OD_LKG Leakage current Output is Hi-Z, VIN = 0 to LDO_3V3  –1 1 μA
SBU
SBU_VIH High-level input voltage LDO_3V3 = 3.3 V 2 V
SBU_VIL Low-level input voltage LDO_3V3 = 3.3 V 0.8 V
SBU_HYS Input hysteresis voltage LDO_3V3 = 3.3 V 0.2  V