SBVS446A August   2023  – January 2024 TPS7A53B

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Voltage Regulation Features
        1. 6.3.1.1 DC Regulation
        2. 6.3.1.2 AC and Transient Response
      2. 6.3.2 System Start-Up Features
        1. 6.3.2.1 Programmable Soft-Start (NR/SS Pin)
        2. 6.3.2.2 Internal Sequencing
          1. 6.3.2.2.1 Enable (EN)
          2. 6.3.2.2.2 Undervoltage Lockout (UVLO) Control
          3. 6.3.2.2.3 Active Discharge
        3. 6.3.2.3 Power-Good Output (PG)
      3. 6.3.3 Internal Protection Features
        1. 6.3.3.1 Foldback Current Limit (ICL)
        2. 6.3.3.2 Thermal Protection (Tsd)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Regulation
      2. 6.4.2 Disabled
      3. 6.4.3 Current Limit Operation
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1  Recommended Capacitor Types
        1. 7.1.1.1 Input and Output Capacitor Requirements (CIN and COUT)
        2. 7.1.1.2 Noise-Reduction and Soft-Start Capacitor (CNR/SS)
        3. 7.1.1.3 Feed-Forward Capacitor (CFF)
      2. 7.1.2  Soft-Start and Inrush Current
      3. 7.1.3  Optimizing Noise and PSRR
      4. 7.1.4  Charge Pump Noise
      5. 7.1.5  Current Sharing
      6. 7.1.6  Adjustable Operation
      7. 7.1.7  Power-Good Operation
      8. 7.1.8  Undervoltage Lockout (UVLO) Operation
      9. 7.1.9  Dropout Voltage (VDO)
      10. 7.1.10 Device Behavior During Transition From Dropout Into Regulation
      11. 7.1.11 Load Transient Response
      12. 7.1.12 Reverse Current Protection Considerations
      13. 7.1.13 Power Dissipation (PD)
      14. 7.1.14 Estimating Junction Temperature
      15. 7.1.15 TPS7A53EVM Thermal Analysis
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 Board Layout
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.1.7 Power-Good Operation

For proper operation of the power-good circuit, the pullup resistor value must be between 10kΩ and 100kΩ. The lower limit of 10kΩ results from the maximum pulldown strength of the power-good transistor, and the upper limit of 100kΩ results from the maximum leakage current at the power-good node. If the pullup resistor is outside this range, then the power-good signal can possibly be unable to read a valid digital logic level.

Using a large CFF with a small CNR/SS causes the power-good signal to incorrectly indicate that the output voltage has settled during turn-on. The CFF time constant must be greater than the soft-start time constant for proper operation of the PG during start-up. For a detailed description, see the Pros and Cons of Using a Feed-Forward Capacitor with a Low Dropout Regulator application note.

The state of PG is only valid when the device operates above the minimum supply voltage. During short UVLO events and at light loads, power-good does not assert because the output voltage is sustained by the output capacitance.