SBVS441 December   2022 TPS7B4255

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6.     Timing Characteristics
    7. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Regulated Output (VOUT)
      2. 7.3.2 Undervoltage Lockout
      3. 7.3.3 Thermal Protection
      4. 7.3.4 Current Limit
      5. 7.3.5 VOUT Short to Battery
      6. 7.3.6 Tracking Regulator With an Enable Circuit
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation With VIN < 3 V
      2. 7.4.2 Operation With ADJ/EN Control
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Dropout Voltage
      2. 8.1.2 Reverse Current
      3. 8.1.3 Signal-Buffering LDO
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Input and Output Capacitor Selection
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
        1. 8.4.1.1 Package Mounting
        2. 8.4.1.2 Board Layout Recommendations to Improve PSRR and Noise Performance
        3. 8.4.1.3 Power Dissipation and Thermal Considerations
        4. 8.4.1.4 Thermal Performance Versus Copper Area
      2. 8.4.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Device Nomenclature
      2. 9.1.2 Development Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  10. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

5 Pin Configuration and Functions

Figure 5-1 DBV Package,5-Pin SOT-23(Top View)
Table 5-1 Pin Functions
PIN TYPE DESCRIPTION
NAME NO.
ADJ/EN 1 I ADJ/EN pin. Connect the reference voltage to this pin. This pin connects to the error amplifier internally. A low signal below VIL disables the device and a high signal above VIH enables the device. Connect the voltage reference directly or with a voltage divider for lower output voltages. To compensate for line influences, place a capacitor close to this pin.
GND 2 — Ground pin.
NC 5 — This pin is not internally connected. Connect this pin to GND for improved thermal performance.
IN 3 I Input power-supply voltage pin. This pin is the device supply. For best transient response and to minimize input impedance, use the recommended value or larger ceramic capacitor from IN to GND as listed in the Section 6.3 table. Place the input capacitor as close to the input of the device as possible to compensate for line influences.
OUT 4 O Regulated output voltage pin. A capacitor is required from OUT to GND for stability. For best transient response, use the nominal recommended value or larger ceramic capacitor from OUT to GND; see the Section 6.3 table. Place the output capacitor as close to output of the device as possible.