SNLS696C April   2021  – July 2024 TSER953

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Recommended Timing for the Serial Control Bus
    7. 5.7 Timing Diagrams
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 CSI-2 Receiver
        1. 6.3.1.1 CSI-2 Receiver Operating Modes
        2. 6.3.1.2 CSI-2 Receiver High-Speed Mode
        3. 6.3.1.3 CSI-2 Protocol Layer
        4. 6.3.1.4 CSI-2 Short Packet
        5. 6.3.1.5 CSI-2 Long Packet
        6. 6.3.1.6 CSI-2 Errors and Detection
          1. 6.3.1.6.1 CSI-2 ECC Detection and Correction
          2. 6.3.1.6.2 CSI-2 Check Sum Detection
          3. 6.3.1.6.3 D-PHY Error Detection
          4. 6.3.1.6.4 CSI-2 Receiver Status
      2. 6.3.2 V3Link Forward Channel Transmitter
        1. 6.3.2.1 Frame Format
      3. 6.3.3 V3Link Back Channel Receiver
      4. 6.3.4 Serializer Status and Monitoring
        1. 6.3.4.1 Forward Channel Diagnostics
        2. 6.3.4.2 Back Channel Diagnostics
        3. 6.3.4.3 Voltage and Temperature Sensing
          1. 6.3.4.3.1 Programming Example
        4. 6.3.4.4 Built-In Self Test
      5. 6.3.5 FrameSync Operation
        1. 6.3.5.1 External FrameSync
        2. 6.3.5.2 Internally Generated FrameSync
      6. 6.3.6 GPIO Support
        1. 6.3.6.1 GPIO Status
        2. 6.3.6.2 GPIO Input Control
        3. 6.3.6.3 GPIO Output Control
        4. 6.3.6.4 Forward Channel GPIO
        5. 6.3.6.5 Back Channel GPIO
    4. 6.4 Device Functional Modes
      1. 6.4.1 Clocking Modes
        1. 6.4.1.1 Synchronous Mode
        2. 6.4.1.2 Non-Synchronous Clock Mode
        3. 6.4.1.3 Non-Synchronous Internal Mode
        4. 6.4.1.4 DVP Compatibility Mode
        5. 6.4.1.5 Configuring CLK_OUT
      2. 6.4.2 MODE
    5. 6.5 Programming
      1. 6.5.1 I2C Interface Configuration
        1. 6.5.1.1 CLK_OUT/IDX
          1. 6.5.1.1.1 IDX
      2. 6.5.2 I2C Interface Operation
      3. 6.5.3 I2C Timing
    6. 6.6 Pattern Generation
      1. 6.6.1 Reference Color Bar Pattern
      2. 6.6.2 Fixed Color Patterns
      3. 6.6.3 Packet Generator Programming
        1. 6.6.3.1 Determining Color Bar Size
      4. 6.6.4 Code Example for Pattern Generator
    7. 6.7 Register Maps
      1. 6.7.1 Main Registers
        1. 6.7.1.1  I2C Device ID Register
        2. 6.7.1.2  Reset
        3. 6.7.1.3  General Configuration
        4. 6.7.1.4  Forward Channel Mode Selection
        5. 6.7.1.5  BC_MODE_SELECT
        6. 6.7.1.6  PLL Clock Control
        7. 6.7.1.7  Clock Output Control 0
        8. 6.7.1.8  Clock Output Control 1
        9. 6.7.1.9  Back Channel Watchdog Control
        10. 6.7.1.10 I2C Control 1
        11. 6.7.1.11 I2C Control 2
        12. 6.7.1.12 SCL High Time
        13. 6.7.1.13 SCL Low Time
        14. 6.7.1.14 Local GPIO DATA
        15. 6.7.1.15 GPIO Input Control
        16. 6.7.1.16 DVP_CFG
        17. 6.7.1.17 DVP_DT
        18. 6.7.1.18 Force BIST Error
        19. 6.7.1.19 Remote BIST Control
        20. 6.7.1.20 Sensor Voltage Gain
        21. 6.7.1.21 Sensor Control 0
        22. 6.7.1.22 Sensor Control 1
        23. 6.7.1.23 Voltage Sensor 0 Thresholds
        24. 6.7.1.24 Voltage Sensor 1 Thresholds
        25. 6.7.1.25 Temperature Sensor Thresholds
        26. 6.7.1.26 CSI-2 Alarm Enable
        27. 6.7.1.27 Alarm Sense Enable
        28. 6.7.1.28 Back Channel Alarm Enable
        29. 6.7.1.29 CSI-2 Polarity Select
        30. 6.7.1.30 CSI-2 LP Mode Polarity
        31. 6.7.1.31 CSI-2 High-Speed RX Enable
        32. 6.7.1.32 CSI-2 Low Power Enable
        33. 6.7.1.33 CSI-2 Termination Enable
        34. 6.7.1.34 CSI-2 Packet Header Control
        35. 6.7.1.35 Back Channel Configuration
        36. 6.7.1.36 Datapath Control 1
        37. 6.7.1.37 Remote Partner Capabilities 1
        38. 6.7.1.38 Partner Deserializer ID
        39. 6.7.1.39 Target 0 ID
        40. 6.7.1.40 Target 1 ID
        41. 6.7.1.41 Target 2 ID
        42. 6.7.1.42 Target 3 ID
        43. 6.7.1.43 Target 4 ID
        44. 6.7.1.44 Target 5 ID
        45. 6.7.1.45 Target 6 ID
        46. 6.7.1.46 Target 7 ID
        47. 6.7.1.47 Target 0 Alias
        48. 6.7.1.48 Target 1 Alias
        49. 6.7.1.49 Target 2 Alias
        50. 6.7.1.50 Target 3 Alias
        51. 6.7.1.51 Target 4 Alias
        52. 6.7.1.52 Target 5 Alias
        53. 6.7.1.53 Target 6 Alias
        54. 6.7.1.54 Target 7 Alias
        55. 6.7.1.55 Back Channel Control
        56. 6.7.1.56 Revision ID
        57. 6.7.1.57 Device Status
        58. 6.7.1.58 General Status
        59. 6.7.1.59 GPIO Pin Status
        60. 6.7.1.60 BIST Error Count
        61. 6.7.1.61 CRC Error Count 1
        62. 6.7.1.62 CRC Error Count 2
        63. 6.7.1.63 Sensor Status
        64. 6.7.1.64 Sensor V0
        65. 6.7.1.65 Sensor V1
        66. 6.7.1.66 Sensor T
        67. 6.7.1.67 CSI-2 Error Count
        68. 6.7.1.68 CSI-2 Error Status
        69. 6.7.1.69 CSI-2 Errors Data Lanes 0 and 1
        70. 6.7.1.70 CSI-2 Errors Data Lanes 2 and 3
        71. 6.7.1.71 CSI-2 Errors Clock Lane
        72. 6.7.1.72 CSI-2 Packet Header Data
        73. 6.7.1.73 Packet Header Word Count 0
        74. 6.7.1.74 Packet Header Word Count 1
        75. 6.7.1.75 CSI-2 ECC
        76. 6.7.1.76 IND_ACC_CTL
        77. 6.7.1.77 IND_ACC_ADDR
        78. 6.7.1.78 IND_ACC_DATA
        79. 6.7.1.79 V3LINK_TX_ID0
        80. 6.7.1.80 V3LINK_TX_ID1
        81. 6.7.1.81 V3LINK_TX_ID2
        82. 6.7.1.82 V3LINK_TX_ID3
        83. 6.7.1.83 V3LINK_TX_ID4
        84. 6.7.1.84 V3LINK_TX_ID5
      2. 6.7.2 Indirect Access Registers
        1. 6.7.2.1 PATGEN Registers
        2. 6.7.2.2 V3Link TX Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1 Power-over-Coax
    2. 7.2 Typical Applications
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 CSI-2 Interface
        2. 7.2.2.2 V3Link Input / Output
        3. 7.2.2.3 Internal Regulator Bypassing
        4. 7.2.2.4 Loop Filter Decoupling
      3. 7.2.3 Application Curve
    3. 7.3 Power Supply Recommendations
      1. 7.3.1 Power-Up Sequencing
        1. 7.3.1.1 System Initialization
          1. 7.3.1.1.1 Example Code for Temperature Ramp Initialization
      2. 7.3.2 Power Down (PDB)
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 CSI-2 Guidelines
      2. 7.4.2 Layout Examples
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9 Revision History

Changes from Revision B (March 2023) to Revision C (July 2024)

  • Updated I2C_SDA and I2C_SCL description to denote pull-up resistors are system dependentGo
  • Updated specifications for ending temperature when ambient temperature is decreasing from start upGo
  • Added table for deserializer SENSOR_STS_x register bit descriptionGo
  • Updated ADC Code vs Temperature table for clarity with reference to device operating temperature rangeGo
  • Clarified PGEN_LINE_PD calculation based on frame rate, total lines per frame, and forward channel rateGo
  • Updated register map to remove registers previously marked as reservedGo
  • Published 0x1E ALARM_BC_EN[6:2]Go
  • Reserved DIE ID register page from register 0xB0 for clarityGo
  • Published Analog registers 0x4B and 0x4CGo
  • Removed DIE ID register page from Indirect Register Map table for clarityGo
  • Updated Typical PoC Network example to include reference to Design Parameters Table Go
  • Updated Typical Applications diagrams to denote pull-up resistors values are system dependentGo
  • Added information describing serializer system initialization for continuous PLL lock Go
  • Added initialization sequence example for continuous PLL lock during serializer temperature rampGo

Changes from Revision A (May 2021) to Revision B (March 2023)

  • Typical power consumption bullet on front page updated to match electrical characteristics tableGo
  • Added note for supply noise frequency rangeGo
  • IDD_TOTAL typical value changed to 160mAGo
  • Changed I2C terminology to "Controller" and "Target"Go
  • Removed extra arrow from DPHY Receiver to Clock Gen blocks in Functional Block Diagram Go
  • Added description for non-continuous clock lane modeGo
  • Added description for deserializer SENSOR_STS_x registersGo
  • Updated script example for voltage monitoringGo
  • Updated description for reading GPIO status when set as output and added GPIO Configuration tableGo
  • Added information for enabling Forward Channel GPIO using FC_GPIO_ENGo
  • Updated GPIO Output Control section description for enabling register 0x0EGo
  • Updated Clocking Mode table with additional modes, frequency clarifications, and CSI-2 bandwidth clarificationsGo
  • Corrected effect of setting M value in register 0x06Go
  • Added max and min readings to Voltage Sensor Thresholds description in Register 0x19 Go
  • Changed "GPIO0 Sensor" to "Internal Temperature Sensor" in register 0x57Go
  • V3LINK_RX_ID changed to V3LINK_TX_ID in register 0xF0-0xF5Go
  • Changed PoC network impedance recommendation from 2kΩ to 1 kΩGo
  • Updated PoC descriptionGo
  • Changed PDB capacitor value to "> 10μF"Go
  • Changed PDB capacitor value from 1μF to 10μFGo

Changes from Revision * (April 2021) to Revision A (May 2021)

  • Updated images with searchable text and layoutGo