SLLSFI4D November   2021  – April 2024 TUSB2E11

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Version Comparison
    1. 4.1 Device Variants
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
    4. 8.4 Device Functional Modes
      1. 8.4.1  Repeater Mode
      2. 8.4.2  Power Down Mode
      3. 8.4.3  Disabled Mode
      4. 8.4.4  UART Mode
      5. 8.4.5  Auto-Resume ECR
      6. 8.4.6  L2 State Interrupt Modes
      7. 8.4.7  Attach Detect Interrupt Mode
      8. 8.4.8  GPIO Mode
      9. 8.4.9  USB 2.0 High-Speed HOST Disconnect Detection
      10. 8.4.10 Frame Based Low Power Mode
      11. 8.4.11 Battery Charging
    5. 8.5 Manufacturing Test Modes
      1. 8.5.1 USB DP Test Procedure
      2. 8.5.2 USB DM Test Procedure
    6. 8.6 I2C Target Interface
  10. 9 Register Access Protocol (RAP)
  11. 10Register Map
    1. 10.1 TUSB2E11 Registers
  12. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
      3. 11.2.3 Application Curves
    3. 11.3 Power Supply Recommendations
      1. 11.3.1 Power Up Reset
    4. 11.4 Layout
      1. 11.4.1 Layout Guidelines
      2. 11.4.2 Example Layout for Application with 1.8V I2C Variant
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Support Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

11.2.1 Design Requirements

The TUSB2E11 requires a valid reset signal as described in the Power Supply Recommendations section.

For design examples, use the parameters shown in Table 11-1, Table 11-2, and Table 11-3.

Table 11-1 Design Parameters for High Loss USB 2.0 System Using I2C
PARAMETER VALUE(1)
VDD3V3 3.3V ±10%
VDD1V8 1.8V ±5%
I2C support required in system (Yes or No) Yes
Parameter Register Setting Value
USB 2.0 TX Swing (peak to peak) U_TX_ADJUST_PORT1
(Offset = 70h)		 7Ch 980mVp-p
USB 2.0 TX Pre-emphasis U_HS_TX_PRE_EMPHASIS_P1
(Offset = 71h)		 3Ch 2.1dB
USB 2.0 RX Equalization U_RX_ADJUST_PORT1
(Offset = 72h)		 92h 1.09dB
USB 2.0 HS host disconnect threshold (peak differential) U_DISCONNECT_SQUELCH_PORT1
(Offset = 73h)		 83h 685mV
USB 2.0 HS squelch/RX sensitivity threshold (peak differential) U_DISCONNECT_SQUELCH_PORT1
(Offset = 73h)		 83h 111mV
Table 11-2 Design Parameters for Medium Loss USB 2.0 System Using I2C
PARAMETER VALUE(1)
VDD3V3 3.3V ±10%
VDD1V8 1.8V ±5%
I2C support required in system (Yes or No) Yes
Parameter Register Setting Value
USB 2.0 TX Swing (peak to peak) U_TX_ADJUST_PORT1
(Offset = 70h)		 79h 920mVp-p
USB 2.0 TX Pre-emphasis U_HS_TX_PRE_EMPHASIS_P1
(Offset = 71h)		 39h 0.9dB
USB 2.0 RX Equalization U_RX_ADJUST_PORT1
(Offset = 72h)		 92h 1.09dB
USB 2.0 HS host disconnect threshold (peak differential) U_DISCONNECT_SQUELCH_PORT1
(Offset = 73h)		 83h 685mV
USB 2.0 HS squelch/RX sensitivity threshold (peak differential) U_DISCONNECT_SQUELCH_PORT1
(Offset = 73h)		 83h 111mV
(1) These parameters are starting values for a high loss system. Further tuning might be required based on specific loss profile and measurements.
Table 11-3 Design Parameters for Medium Loss USB 2.0 System without I2C and Configured for Charger Detection
PARAMETER VALUE(1)
VDD3V3 3.3V ±10%
VDD1V8 1.8V ±5%
I2C support required in system (Yes or No) No
SCL (pulldown resistor to ground) 1.65kΩ
SDA (pulldown resistor to ground) 100kΩ
SDA (pullup resistor to VBUS5V) 324kΩ
Parameter GPIO0 GPIO1 GPIO2 Value
USB 2.0 TX Swing (peak to peak) Float Pull-up Pull-up 920mVp-p
USB 2.0 TX Pre-emphasis Float Pull-up Pull-up 0.9dB
USB 2.0 RX Equalization Float Pull-up Pull-up 1.09dB
USB 2.0 HS host disconnect threshold (peak differential) Float Pull-up Pull-up 685mV
USB 2.0 HS squelch/RX sensitivity threshold (peak differential) Float Pull-up Pull-up 98mV
(1) These parameters are starting values for a medium loss system. Further tuning might be required based on specific loss profile and measurements.