SLLSFZ6 November   2024 TUSB5461-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Supply Characteristics
    6. 5.6  Control I/O DC Electrical Characteristics
    7. 5.7  USB and DP Electrical Characteristics
    8. 5.8  Timing Requirements
    9. 5.9  Switching Characteristics
    10. 5.10 Typical Characteristics
  7.   Parameter Measurement Information
  8. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 USB 3.2
      2. 6.3.2 DisplayPort
      3. 6.3.3 4-Level Inputs
      4. 6.3.4 Receiver Linear Equalization
    4. 6.4 Device Functional Modes
      1. 6.4.1 Device Configuration in GPIO Mode
      2. 6.4.2 Device Configuration In I2C Mode
      3. 6.4.3 DisplayPort Mode
      4. 6.4.4 Linear EQ Configuration
      5. 6.4.5 Linearity VOD
      6. 6.4.6 VOD Modes
        1. 6.4.6.1 Linearity VOD
        2. 6.4.6.2 Limited VOD
      7. 6.4.7 Transmit Equalization
      8. 6.4.8 USB3.2 Modes
      9. 6.4.9 Downstream Facing Port Adaptive Equalization
        1. 6.4.9.1 Fast Adaptive Equalization in I2C Mode
        2. 6.4.9.2 Full Adaptive Equalization
        3. 6.4.9.3 Full Adaptive Equalization in GPIO Mode (I2C_EN = "F")
    5. 6.5 Programming
      1. 6.5.1 Transition Between Modes
      2. 6.5.2 Pseudocode Examples
        1. 6.5.2.1 Fast AEQ With Linear Redriver Mode
        2. 6.5.2.2 Fast AEQ With Limited Redriver Mode
        3. 6.5.2.3 Full AEQ With Linear Redriver Mode
        4. 6.5.2.4 Full AEQ With Limited Redriver Mode
      3. 6.5.3 TUSB5461-Q1 I2C Address Options
      4. 6.5.4 TUSB5461-Q1 I2C Target Behavior
  9. 7 Register Maps
    1. 7.1 TUSB5461-Q1 Registers
  10. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 USB and DP Upstream Facing Port (USB Host / DP GPU to USB-C Receptacle) Configuration
        2. 8.2.2.2 USB Downstream Facing Port (USB-C Receptacle to USB Host) Configuration
          1. 8.2.2.2.1 Fixed Equalization
          2. 8.2.2.2.2 Fast Adaptive Equalization
          3. 8.2.2.2.3 Full Adaptive Equalization
        3. 8.2.2.3 ESD Protection
      3. 8.2.3 Application Curve
    3. 8.3 System Examples
      1. 8.3.1 USB 3.1 Only
      2. 8.3.2 USB 3.1 and 2-Lane DisplayPort Mode
      3. 8.3.3 DisplayPort Only
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  11. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  12. 10Revision History
  13. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information
    2. 11.2 Mechanical Data

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

5.9 Switching Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
AUXp or AUXn and SBU1 or SBU2
tAUX_PD Switch propagation delay 400 ps
tAUX_SW_OFF Switching time CTL1 to switch OFF. Not including TCTL1_DEBOUNCE. Refer to Figure 6-7. 500 ns
tAUX_SW_ON Switching time CTL1 to switch ON Refer to Figure 6-6. 500 ns
tAUX_INTRA Intra-pair output skew 100 ps
USB and DisplayPort Mode Transition Requirement GPIO Mode
tGP_USB_4DP Min overlap of CTL0 and CTL1 when transitioning from USB3 only mode to 4-Lane DisplayPort mode or vice versa. I2C_EN = 0; Refer to Figure 6-2. 4 µs
CTL1 and HPDIN
tHPDIN_DEBOUNCE CTL1 and HPDIN debounce time when transitioning from H to L. 2 10 ms
I2C
fSCL I2C clock frequency 1 MHz
tBUF Bus-free time between START and STOP conditions Refer to Figure 6-1 0.5 µs
tHDSTA Hold time after repeated START condition. After this period, the first clock pulse is generated Refer to Figure 6-1 0.26 µs
tLOW Low period of the I2C clock Refer to Figure 6-1 0.5 µs
tHIGH High period of the I2C clock Refer to Figure 6-1 0.26 µs
tSUSTA Setup time for a repeated START condition Refer to Figure 6-1 0.26 µs
tHDDAT Data hold time Refer to Figure 6-1 0.008 µs
tSUDAT Data setup time Refer to Figure 6-1 50 ns
tR Rise time of both SDA and SCL signals Refer to Figure 6-1 120 ns
tF Fall time of both SDA and SCL signals Refer to Figure 6-1 1.2 120 ns
tSUSTO Setup time for STOP condition Refer to Figure 6-1 0.26 µs
Cb Capacitive load for each bus line 150 pF