SLUSCK4C September 2016 – October 2024 UCC28950-Q1 , UCC28951-Q1
PRODUCTION DATA
- 1
- 1 Features
- 2 Applications
- 3 Description
- 4 Pin Configuration and Functions
- 5 Specifications
-
6 Detailed Description
- 6.1 Overview
- 6.2 Functional Block Diagram
- 6.3
Feature Description
- 6.3.1 Start-Up Protection Logic
- 6.3.2 Voltage Reference (VREF)
- 6.3.3 Error Amplifier (EA+, EA–, COMP)
- 6.3.4 Soft-Start and Enable (SS/EN)
- 6.3.5 Light-Load Power Saving Features
- 6.3.6 Adaptive Delay, (Delay Between OUTA and OUTB, OUTC and OUTD (DELAB, DELCD, ADEL))
- 6.3.7 Adaptive Delay (Delay Between OUTA and OUTF, OUTB and OUTE (DELEF, ADELEF)
- 6.3.8 Minimum Pulse (TMIN)
- 6.3.9 Burst Mode
- 6.3.10 Switching Frequency Setting
- 6.3.11 Slope Compensation (RSUM)
- 6.3.12 Dynamic SR ON/OFF Control (DCM Mode)
- 6.3.13 Current Sensing (CS)
- 6.3.14 Cycle-by-Cycle Current Limit Current Protection and Hiccup Mode
- 6.3.15 Synchronization (SYNC)
- 6.3.16 Outputs (OUTA, OUTB, OUTC, OUTD, OUTE, OUTF)
- 6.3.17 Supply Voltage (VDD)
- 6.3.18 Ground (GND)
- 6.4 Device Functional Modes
-
7 Application and Implementation
- 7.1 Application Information
- 7.2
Typical Application
- 7.2.1 Design Requirements
- 7.2.2
Detailed Design Procedure
- 7.2.2.1 Power Loss Budget
- 7.2.2.2 Preliminary Transformer Calculations (T1)
- 7.2.2.3 QA, QB, QC, QD FET Selection
- 7.2.2.4 Selecting LS
- 7.2.2.5 Selecting Diodes DB and DC
- 7.2.2.6 Output Inductor Selection (LOUT)
- 7.2.2.7 Output Capacitance (COUT)
- 7.2.2.8 Select FETs QE and QF
- 7.2.2.9 Input Capacitance (CIN)
- 7.2.2.10 Current Sense Network (CT, RCS, R7, DA)
- 7.2.3 Application Curves
- 7.3 Power Supply Recommendations
- 7.4 Layout
- 8 Device and Documentation Support
- 9 Revision History
- 10Mechanical, Packaging, and Orderable Information
Package Options
Mechanical Data (Package|Pins)
- PW|24
Thermal pad, mechanical data (Package|Pins)
Orderable Information
5.8 Typical Characteristics
Figure 5-3 UVLO
Thresholds vs Temperature
Figure 5-5 Supply Current vs Temperature
Figure 5-7 Voltage Reference (VDD = 12V) vs Temperature
Figure 5-9 Short-Circuit Current vs Temperature
Figure 5-11 Nominal Switching Frequency vs Temperature
Figure 5-13 Error
Amplifier Offset Voltage vs Temperature
Figure 5-15 ISS Charge Current vs Temperature
Figure 5-17 SS
Pullup Threshold vs Temperature
Figure 5-19 Current Sense Cycle-by-Cycle Limit vs Temperature
Figure 5-21 Outputs Sink Resistance vs Temperature
Figure 5-23 Outputs Source Resistance vs Temperature
Figure 5-25 Dead
Time Delay vs Temperature
Figure 5-27 DCM
Threshold vs Temperature
Figure 5-4 UVLO
Hysteresis vs Temperature
Figure 5-6 Start-Up Current vs Temperature
Figure 5-8 Line
Voltage Regulation (ILOAD = 10mA) vs Temperature
Figure 5-10 Maximum Duty Cycle vs Temperature
Figure 5-12 Maximum Switching Frequency vs Temperature
Figure 5-14 Voltage Error Amplifier (Open-Loop Gain) vs Temperature
Figure 5-16 Shutdown, Restart, and Reset Threshold vs Temperature
Figure 5-18 SS
Clamp Voltage vs Temperature
Figure 5-20 Current Sense Propagation Delay vs Temperature
Figure 5-22 Outputs Sink Resistance vs Temperature
Figure 5-24 Outputs Source Resistance vs Temperature
Figure 5-26 Dead
Time Delay vs Temperature