SBAS860 Data sheet

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)⁽¹⁾

		MIN	MAX	UNIT
Supply voltage range	AVDD19	–0.3	2.1	V
	AVDD	–0.3	1.4
	DVDD	–0.3	1.4
Voltage applied to input pins	INP, INM	–0.3	AVDD19 + 0.3	V
	CLKINP, CLKINM	–0.3	AVDD + 0.6
	SYSREFP, SYSREFM, SYNCBP, SYNCBM	–0.3	AVDD + 0.6
	SCLK, SEN, SDIN, RESET, PDN, GPIO1, GPIO2, GPIO3, GPIO4	–0.2	AVDD19 + 0.2
Voltage applied to output pins		–0.3	2.2	V
Temperature	Operating free-air, T_A	–40	85	°C
Temperature	Storage, T_stg	–65	150	°C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 ESD Ratings

			VALUE	UNIT
V_(ESD)	Electrostatic discharge	Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001⁽¹⁾	±1000	V
V_(ESD)	Electrostatic discharge	Charged-device model (CDM), per JEDEC specification JESD22-C101⁽²⁾	±500	V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)

		MIN	NOM	MAX	UNIT
Supply voltage⁽²⁾	AVDD19	1.8	1.9	2.0	V
	AVDD	1.1	1.15	1.25
	DVDD	1.1	1.15	1.2
Temperature	Operating free-air, T_A	–40		85	°C
Temperature	Operating junction, T_J		105⁽¹⁾	125	°C

(1) Prolonged use above this junction temperature may increase the device failure-in-time (FIT) rate.

(2) Always power up the DVDD supply (1.15 V) before the AVDD19 (1.9 V) supply. The AVDD (1.15 V) supply can come up in any order.

6.4 Thermal Information

THERMAL METRIC⁽¹⁾		ADC31RF80	UNIT
		RMP (VQFN)
		72 PINS
R_θJA	Junction-to-ambient thermal resistance	21.8	°C/W
R_θJC(top)	Junction-to-case (top) thermal resistance	4.4	°C/W
R_θJB	Junction-to-board thermal resistance	2.0	°C/W
ψ_JT	Junction-to-top characterization parameter	0.1	°C/W
ψ_JB	Junction-to-board characterization parameter	2.0	°C/W
R_θJC(bot)	Junction-to-case (bottom) thermal resistance	0.2	°C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.

6.5 Electrical Characteristics

typical values are specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, 50% clock duty cycle, DDC-bypassed performance, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
POWER CONSUMPTION (Divide-by-4, Complex Output Mode⁽²⁾)
I_AVDD19	1.9-V analog supply current	f_S = 2949.12 MSPS		956	1439	mA
I_AVDD	1.15-V analog supply current	f_S = 2949.12 MSPS		499	813	mA
I_DVDD	1.15-V digital supply current	f_S = 2949.12 MSPS		975	1164	mA
P_D	Power dissipation	f_S = 2949.12 MSPS		3.51	4.71	W
	Global power-down power dissipation			245		mW
ANALOG INPUTS
	Resolution			14		Bits
	Differential input full-scale			1.35		V_PP
V_IC	Input common-mode voltage			1.2⁽³⁾		V
R_IN	Input resistance	Differential resistance at dc		65		Ω
C_IN	Input capacitance	Differential capacitance at dc		2		pF
	V_CM common-mode voltage output			1.2		V
	Analog input bandwidth (–3-dB point)	ADC driven with 50-Ω source		3200		MHz
CLOCK INPUT⁽¹⁾
	Input clock frequency		1.5	3		GSPS
	Differential (peak-to-peak) input clock amplitude		0.5	1.5	2.5	V_PP
	Input clock duty cycle		45%	50%	55%
	Internal clock biasing			1.0		V
	Internal clock termination (differential)			100		Ω

(1) See Figure 79.

(2) Full-scale signal is applied to the analog input; see the Power Consumption in Different Modes section for more details.

(3) When used in dc-coupling mode, the common-mode voltage at the analog inputs should be kept within V_CM ±25 mV for best performance.

6.6 AC Performance Characteristics: f_S = 2949.12 MSPS

typical values specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, 50% clock duty cycle, DDC-bypassed performance⁽⁵⁾, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

PARAMETER		TEST CONDITIONS	MIN⁽³⁾	NOM	UNIT
SNR	Signal-to-noise ratio	f_IN = 100 MHz, A_OUT = –2 dBFS		63.2	dBFS
		f_IN = 900 MHz, A_OUT = –2 dBFS		61.4
		f_IN = 1850 MHz, A_OUT = –2 dBFS	56	58.5
		f_IN = 2100 MHz, A_OUT = –2 dBFS		57.7
		f_IN = 2600 MHz, A_OUT = –2 dBFS		56.6
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		54.6
NSD	Noise spectral density averaged across the Nyquist zone	f_IN = 100 MHz, A_OUT = –2 dBFS		154.9	dBFS/Hz
		f_IN = 900 MHz, A_OUT = –2 dBFS		153.1
		f_IN = 1850 MHz, A_OUT = –2 dBFS	147.7	150.2
		f_IN = 2100 MHz, A_OUT = –2 dBFS		149.4
		f_IN = 2600 MHz, A_OUT = –2 dBFS		148.3
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		146.3
	Small-signal SNR	f_IN = 1850 MHz, A_OUT = –40 dBFS		63.1	dBFS
NF⁽¹⁾	Noise figure	f_IN = 1850 MHz, A_OUT = –40 dBFS		24.7	dB
SINAD	Signal-to-noise and distortion ratio	f_IN = 100 MHz, A_OUT = –2 dBFS		62.1	dBFS
		f_IN = 900 MHz, A_OUT = –2 dBFS		61.0
		f_IN = 1850 MHz, A_OUT = –2 dBFS		57.8
		f_IN = 2100 MHz, A_OUT = –2 dBFS		56.9
		f_IN = 2600 MHz, A_OUT = –2 dBFS		55.7
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		54.5
ENOB	Effective number of bits	f_IN = 100 MHz, A_OUT = –2 dBFS		10.0	Bits
		f_IN = 900 MHz, A_OUT = –2 dBFS		9.8
		f_IN = 1850 MHz, A_OUT = –2 dBFS		9.3
		f_IN = 2100 MHz, A_OUT = –2 dBFS		9.2
		f_IN = 2600 MHz, A_OUT = –2 dBFS		9.0
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		8.8
SFDR	Spurious-free dynamic range	f_IN = 100 MHz, A_OUT = –2 dBFS		68.0	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		71
		f_IN = 1850 MHz, A_OUT = –2 dBFS	58	65
		f_IN = 2100 MHz, A_OUT = –2 dBFS		65
		f_IN = 2600 MHz, A_OUT = –2 dBFS		63
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		68
HD2⁽⁴⁾	Second-order harmonic distortion	f_IN = 100 MHz, A_OUT = –2 dBFS		68	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		71
		f_IN = 1850 MHz, A_OUT = –2 dBFS	58	65
		f_IN = 2100 MHz, A_OUT = –2 dBFS		65
		f_IN = 2700 MHz, A_OUT = –2 dBFS		63
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		68
HD3	Third-order harmonic distortion	f_IN = 100 MHz, A_OUT = –2 dBFS		73	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		80
		f_IN = 1850 MHz, A_OUT = –2 dBFS	62	71
		f_IN = 2100 MHz, A_OUT = –2 dBFS		77
		f_IN = 2600 MHz, A_OUT = –2 dBFS		79
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		76
HD4, HD5	Fourth- and fifth-order harmonic distortion	f_IN = 100 MHz, A_OUT = –2 dBFS		78	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		81.0
		f_IN = 1850 MHz, A_OUT = –2 dBFS	69	76
		f_IN = 2100 MHz, A_OUT = –2 dBFS		77
		f_IN = 2600 MHz, A_OUT = –2 dBFS		77
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		84
IL spur	Interleaving spurs: f_S / 2 – f_IN, f_S / 4 ± f_IN	f_IN = 100 MHz, A_OUT = –2 dBFS		89	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		88
		f_IN = 1850 MHz, A_OUT = –2 dBFS	68	82
		f_IN = 2100 MHz, A_OUT = –2 dBFS		79
		f_IN = 2600 MHz, A_OUT = –2 dBFS		81
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		75
HD2 IL	Interleaving spur for HD2: f_S / 2 – HD2	f_IN = 100 MHz, A_OUT = –2 dBFS		85.0	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		79.0
		f_IN = 1850 MHz, A_OUT = –2 dBFS	62	80.0
		f_IN = 2100 MHz, A_OUT = –2 dBFS		74.0
		f_IN = 2600 MHz, A_OUT = –2 dBFS		74.0
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		80.0
Worst spur	Spurious-free dynamic range (excluding HD2, HD3, HD4, HD5, and interleaving spurs IL and HD2 IL)	f_IN = 100 MHz, A_OUT = –2 dBFS		83.0	dBc
		f_IN = 900 MHz, A_OUT = –2 dBFS		76.0
		f_IN = 1850 MHz, A_OUT = –2 dBFS	64	75.0
		f_IN = 2100 MHz, A_OUT = –2 dBFS		75.0
		f_IN = 2600 MHz, A_OUT = –2 dBFS		75.0
		f_IN = 3500 MHz, A_OUT⁽²⁾ = –3 dBFS with 2-dB gain		72.0
IMD3	Two-tone, third-order intermodulation distortion	f_IN1 = 900 MHz, f_IN2 = 950 MHz, A_OUT = –8 dBFS (each tone)		79	dBFS
		f_IN1 = 1770 MHz, f_IN2 = 1790 MHz, A_OUT = –8 dBFS (each tone)		70
		f_IN1 = 1800 MHz, f_IN2 = 2600 MHz, A_OUT = –8 dBFS (each tone)		73
		f_IN1 = 3490 MHz, f_IN2 = 3510 MHz, A_OUT = –8 dBFS (each tone) with 2-dB gain		67

(1) The ADC internal resistance = 65 Ω, the driving source resistance = 50 Ω.

(2) Output amplitude, A_OUT, refers to the signal amplitude in the ADC digital output that is same as the analog input amplitude, A_IN, except when the digital gain feature is used. If digital gain is G, then A_OUT = G + A_IN.

(3) Minimum values are specified at A_OUT = –3 dBFS.

(4) The minimum value of HD2 is specified by bench characterization.

(5) Performance is shown with DDC bypassed. When DDC is enabled, performance improves by the decimation filtering process.

6.7 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A + D Band⁽¹⁾)

typical values specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, 50% clock duty cycle, DDC-bypassed performance, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

PARAMETER		TEST CONDITIONS	NOM	UNIT
SNR	Signal-to-noise ratio	f_IN = 1850 MHz, A_OUT = –2 dBFS	58.5	dBFS
SNR	Signal-to-noise ratio	f_IN = 2600 MHz, A_OUT = –2 dBFS	55.8	dBFS
SFDR	Spurious-free dynamic range	f_IN = 1850 MHz, A_OUT = –2 dBFS	60.0	dBc
SFDR	Spurious-free dynamic range	f_IN = 2600 MHz, A_OUT = –2 dBFS	57.0	dBc
HD2	Second-order harmonic distortion	f_IN = 1850 MHz, A_OUT = –2 dBFS	59.0	dBc
HD2	Second-order harmonic distortion	f_IN = 2600 MHz, A_OUT = –2 dBFS	57.0	dBc
HD3	Third-order harmonic distortion	f_IN = 1850 MHz, A_OUT = –2 dBFS	75.0	dBc
HD3	Third-order harmonic distortion	f_IN = 2600 MHz, A_OUT = –2 dBFS	65.0	dBc
IL spur	Interleaving spurs: f_S / 2 – f_IN, f_S / 4 ± f_IN	f_IN = 1850 MHz, A_OUT = –2 dBFS	84.0	dBc
IL spur	Interleaving spurs: f_S / 2 – f_IN, f_S / 4 ± f_IN	f_IN = 2600 MHz, A_OUT = –2 dBFS	76.0	dBc
HD2 IL	Interleaving spur for HD2: f_S / 2 – HD2	f_IN = 1850 MHz, A_OUT = –2 dBFS	76.0	dBc
HD2 IL	Interleaving spur for HD2: f_S / 2 – HD2	f_IN = 2600 MHz, A_OUT = –2 dBFS	67.0	dBc
IMD3	Two-tone, third-order intermodulation distortion	f_IN1 = 1800 MHz, f_IN2 = 2600 MHz, A_OUT = –8 dBFS (each tone)	67.0	dBFS

(1) F-band = 1880 MHz to 1920 MHz, A-band = 2010 MHz to 2025 MHz, and D-band = 2570 MHz to 2620 MHz.

6.8 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A Band⁽¹⁾)

typical values specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, 50% clock duty cycle, DDC-bypassed performance, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

PARAMETER		TEST CONDITIONS	NOM	UNIT
SNR	Signal-to-noise ratio	f_IN = 1850 MHz, A_OUT = –2 dBFS	58.7	dBFS
SNR	Signal-to-noise ratio	f_IN = 2100 MHz, A_OUT = –2 dBFS	57.9	dBFS
SFDR	Spurious-free dynamic range	f_IN = 1850 MHz, A_OUT = –2 dBFS	71.0	dBc
SFDR	Spurious-free dynamic range	f_IN = 2100 MHz, A_OUT = –2 dBFS	69.0	dBc
HD2	Second-order harmonic distortion	f_IN = 1850 MHz, A_OUT = –2 dBFS	71.0	dBc
HD2	Second-order harmonic distortion	f_IN = 2100 MHz, A_OUT = –2 dBFS	69.0	dBc
HD3	Third-order harmonic distortion	f_IN = 1850 MHz, A_OUT = –2 dBFS	75.0	dBc
HD3	Third-order harmonic distortion	f_IN = 2100 MHz, A_OUT = –2 dBFS	76.0	dBc
IL spur	Interleaving spurs: f_S / 2 – f_IN, f_S / 4 ± f_IN	f_IN = 1850 MHz, A_OUT = –2 dBFS	82.0	dBc
IL spur	Interleaving spurs: f_S / 2 – f_IN, f_S / 4 ± f_IN	f_IN = 2100 MHz, A_OUT = –2 dBFS	84.0	dBc
HD2 IL	Interleaving spur for HD2: f_S / 2 – HD2	f_IN = 1850 MHz, A_OUT = –2 dBFS	80.0	dBc
HD2 IL	Interleaving spur for HD2: f_S / 2 – HD2	f_IN = 2100 MHz, A_OUT = –2 dBFS	80.0	dBc

(1) F-band = 1880 MHz to 1920 MHz, A-band = 2010 MHz to 2025 MHz, and D-band = 2570 MHz to 2620 MHz.

6.9 Digital Requirements

typical values are specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, DDC bypassed performance, 50% clock duty cycle, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

PARAMETER		TEST CONDITIONS	MIN	NOM	MAX	UNIT
DIGITAL INPUTS (RESET, SCLK, SEN, SDIN, PDN, GPIO1, GPIO2, GPIO3, GPIO4)
V_IH	High-level input voltage		0.8			V
V_IL	Low-level input voltage				0.4	V
I_IH	High-level input current			50		µA
I_IL	Low-level input current			–50		µA
C_i	Input capacitance			4		pF
DIGITAL OUTPUTS (SDOUT, GPIO1, GPIO2, GPIO3, GPIO4)
V_OH	High-level output voltage		AVDD19–0.1	AVDD19		V
V_OL	Low-level output voltage				0.1	V
DIGITAL INPUTS (SYSREFP and SYSREFM; SYNCBP and SYNCBM; Requires External Biasing)
V_ID	Differential input voltage		350	450	800	mV_PP
V_CM	Input common-mode voltage		1.05	1.2	1.325	V
DIGITAL OUTPUTS (JESD204B Interface: D[3:0], Meets JESD204B LV-0IF-11G-SR Standard)
\|V_OD\|	Output differential voltage			700		mV_PP
\|V_OCM\|	Output common-mode voltage			450		mV
	Transmitter short-circuit current	Transmitter pins shorted to any voltage between –0.25 V and 1.45 V	–100		100	mA
z_os	Single-ended output impedance			50		Ω
C_o	Output capacitance	Output capacitance inside the device, from either output to ground		2		pF

6.10 Timing Requirements

typical values are specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and chip sampling rate = 2949.12 MSPS, 50% clock duty cycle, DDC-bypassed performance, AVDD19 = 1.9 V, AVDD = 1.15 V, DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

			MIN	NOM	MAX	UNIT
SAMPLE TIMING
	Aperture delay		250		750	ps
	Aperture delay matching between two devices at the same temperature and supply voltage			±150		ps
	Aperture jitter, clock amplitude = 2 V_PP			90		f_S
Latency ⁽¹⁾⁽³⁾	Data latency, ADC sample to digital output	DDC block bypassed		424		Input clock cycles
	Fast overrange latency, ADC sample to FOVR indication on GPIO pins			70
t_PD	Propagation delay time: logic gates and output buffer delay (does not change with f_S)			6		ns
SYSREF TIMING⁽²⁾
t_{SU_SYSREF}	SYSREF setup time: referenced to clock rising edge, 2949.12 MSPS		140	70		ps
t_{H_SYSREF}	SYSREF hold time: referenced to clock rising edge, 2949.12 MSPS		50	20		ps
	Valid transition window sampling period: t_{SU_SYSREF} – t_{H_SYSREF}, 2949.12 MSPS		143			ps
JESD OUTPUT INTERFACE TIMING
UI	Unit interval: 12.5 Gbps		80	100	400	ps
	Serial output data rate		2.5	10.0	12.5	Gbps
	Rise, fall times: 1-pF, single-ended load capacitance to ground			60		ps
	Total jitter: BER of 1E-15 and lane rate = 12.5 Gbps			25		%UI
	Random jitter: BER of 1E-15 and lane rate = 12.5 Gbps			0.99		%UI, rms
	Deterministic jitter: BER of 1E-15 and lane rate = 12.5 Gbps			9.1		%UI, pk-pk

(1) Overall latency = latency + t_PD.

(2) Common-mode voltage for the SYSREF input is kept at 1.2 V.

(3) Latency increases when the DDC modes are used; see Table 4.

6.11 Typical Characteristics

typical values are specified at an ambient temperature of 25°C; minimum and maximum values are specified over an ambient temperature range of –40°C to +85°C; and ADC sampling rate = 2949.12 MSPS, DDC bypassed performance, 50% clock duty cycle, AVDD19 = 1.9 V, AVDD = DVDD = 1.15 V, –2-dBFS differential input, and 0-dB digital gain (unless otherwise noted)

SNR = 63.4 dBFS; SFDR = 69 dBc;
HD2 = –69 dBc; HD3 = –71 dBc; non HD2, HD3 = 80 dBc;
IL spur = 82 dBc; f_IN = 100 MHz

Figure 3. FFT for 100-MHz Input Frequency

SNR = 60.8 dBFS; SFDR = 71 dBc;
HD2 = –71 dBc; HD3 = –80 dBc; non HD2, HD3 = 83 dBc;
IL spur = 83 dBc; f_IN = 900 MHz

Figure 5. FFT for 900-MHz Input Signal

SNR = 58.9 dBFS; SFDR = 69 dBc;
HD2 = –69 dBc; HD3 = –71 dBc; non HD2, HD3 = 77 dBc;
IL spur = 76 dBc; f_IN = 1.85 GHz

Figure 7. FFT for 1850-MHz Input Signal

SNR = 57.9 dBFS; SFDR = 63 dBc;
HD2 = –63 dBc; HD3 = –76 dBc; non HD2, HD3 = 78 dBc;
IL spur = 73 dBc; f_IN = 2.1 GHz

Figure 9. FFT for 2100-MHz Input Signal

SNR = 56.8 dBFS; SFDR = 65 dBc;
HD2 = –65 dBc; HD3 = –71 dBc; non HD2, HD3 = 89 dBc;
IL spur = 74 dBc; f_IN = 2.6 GHz

Figure 11. FFT for 2600-MHz Input Signal

SNR = 54.6 dBFS; SFDR = 70 dBc;
HD2 = –72 dBc; HD3 = –74 dBc; non HD2, HD3 = 70 dBc;
IL spur = 76 dBc; f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB gain

Figure 13. FFT for 3500-MHz Input Signal

f_IN1 = 900 MHz, f_IN2 = 950 MHz, A_IN = –8 dBFS, IMD = 79 dBFS

Figure 15. FFT for Two-Tone Input Signal (–8 dBFS)

f_IN1 = 900 MHz, f_IN2 = 950 MHz, A_IN = –8 dBFS, IMD = 78 dBFS

Figure 17. FFT for Two-Tone Input Signal
(–8 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.77 GHz, f_IN2 = 1.79 GHz, A_IN = –8 dBFS, IMD = 75 dBFS

Figure 19. FFT for Two-Tone Input Signal (–8 dBFS)

f_IN1 = 1.77 GHz, f_IN2 = 1.79 GHz, A_IN = –8 dBFS,
IMD = 76 dBFS

Figure 21. FFT for Two-Tone Input Signal
(–8 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.8 MHz, f_IN2 = 2.6 GHz, A_IN = –8 dBFS, IMD = 70 dBFS

Figure 23. FFT for Two-Tone Input Signal (–8 dBFS)

f_IN1 = 2.09 GHz, f_IN2 = 2.1 GHz, A_IN = –8 dBFS, IMD = 71 dBFS

Figure 25. FFT for Two-Tone Input Signal
(–8 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 3.49 MHz, f_IN2 = 3.51 GHz, IMD = 75 dBFS,
A_IN = –8 dBFS with 2-dB gain

Figure 27. FFT for Two-Tone Input Signal (–8 dBFS)

f_IN1 = 2.59 GHz, f_IN2 = 2.6 GHz, A_IN = –8 dBFS, IMD = 68 dBFS

Figure 29. FFT for Two-Tone Input Signal
(–8 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.77 GHz, f_IN2 = 1.79 GHz

Figure 31. Intermodulation Distortion vs Input Amplitude (1770 MHz and 1790 MHz)

f_IN1 = 1.8 GHz, f_IN2 = 2.6 GHz, A_IN = –36 dBFS

Figure 33. Intermodulation Distortion vs Input Amplitude (1800 MHz and 2600 MHz)

f_IN1 = 3.49 GHz, f_IN2 = 3.51 GHz with 2-dB digital gain

Figure 35. Intermodulation Distortion vs Input Amplitude (3490 MHz and 3510 MHz)

Figure 37. Spurious-Free Dynamic Range vs
Input Frequency

Figure 39. IL Spur vs Input Frequency

Figure 41. Signal-to-Noise Ratio vs Input Frequency

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 43. Signal-to-Noise Ratio vs
AVDD Supply and Temperature

f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 45. Signal-to-Noise Ratio vs
AVDD Supply and Temperature

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 47. Signal-to-Noise Ratio vs
DVDD Supply and Temperature

f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 49. Signal-to-Noise Ratio vs
DVDD Supply and Temperature

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 51. Signal-to-Noise Ratio vs
AVDD19 Supply and Temperature

f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 53. Signal-to-Noise Ratio vs
AVDD19 Supply and Temperature

f_IN = 1.78 GHz, A_OUT = –2 dBFS

Figure 55. HD2 Histogram at AVDD19 = 1.8 V

f_IN = 1.78 GHz, A_OUT = –2 dBFS

Figure 57. HD2 Histogram at AVDD19 = 2.0 V

f_IN = 3.5 GHz

Figure 59. Performance vs Amplitude

f_IN = 3.5 GHz, A_IN = –3 dBFS

Figure 61. Performance vs Clock Amplitude

f_IN = 3.5 GHz

Figure 63. Performance vs Clock Duty Cycle

Figure 65. Power-Supply Rejection Ratio vs
Tone Frequency

Figure 67. Common-Mode Rejection Ratio vs
Tone Frequency

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 61.6 dBFS, SFDR (includes IL) = 82 dBc

Figure 69. FFT in 6x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 63 dBFS, SFDR (includes IL) = 82 dBc

Figure 71. FFT in 9x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 63.7 dBFS, SFDR (includes IL) = 83 dBc

Figure 73. FFT in 12x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 64 dBFS, SFDR (includes IL) = 83 dBc

Figure 75. FFT in 18x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 64.4 dBFS, SFDR (includes IL) = 82 dBc

Figure 77. FFT in 24x Decimation (Complex Output)

SNR = 63.3 dBFS; SFDR = 72 dBc;
HD2 = –72 dBc; HD3 = –87 dBc; non HD2, HD3 = 85 dBc;
IL spur = 80 dBc; f_IN = 100 MHz

Figure 4. FFT for 100-MHz Input Signal (f_S = 2457.6 MSPS)

SNR = 61.4 dBFS; SFDR = 71 dBc;
HD2 = –80 dBc; HD3 = –73 dBc; non HD2, HD3 = 74 dBc;
IL spur = 80 dBc; f_IN = 900 MHz

Figure 6. FFT for 900-MHz Input Signal (f_S = 2457.6 MSPS)

SNR = 58.9 dBFS; SFDR = 71 dBc;
HD2 = –71 dBc; HD3 = –75 dBc; non HD2, HD3 = 78 dBc;
IL spur = 76 dBc; f_IN = 1.85 GHz

Figure 8. FFT for 1850-MHz Input Signal (f_S = 2457.6 MSPS)

SNR = 58.2 dBFS; SFDR = 64 dBc;
HD2 = –64 dBc; HD3 = –81 dBc; non HD2, HD3 = 83 dBc;
IL spur = 80 dBc; f_IN = 2.1 GHz

Figure 10. FFT for 2100-MHz Input Signal (f_S = 2457.6 MSPS)

SNR = 56.8 dBFS; SFDR = 60 dBc;
HD2 = –60 dBc; HD3 = –71 dBc; non HD2, HD3 = 73 dBc;
IL spur = 75 dBc; f_IN = 2.6 GHz

Figure 12. FFT for 2600-MHz Input Signal (f_S = 2457.6 MSPS)

SNR = 54.9 dBFS; SFDR = 48 dBc;
HD2 = –48 dBc; HD3 = –53 dBc; non HD2, HD3 = 68 dBc;
IL spur = 69 dBc; f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB gain

Figure 14. FFT for 3500-MHz Input Signal (f_S = 2457.6 MSPS)

f_IN1 = 900 MHz, f_IN2 = 950 MHz, A_IN = –36 dBFS, IMD = 94 dBFS

Figure 16. FFT for Two-Tone Input Signal (–36 dBFS)

f_IN1 = 900 MHz, f_IN2 = 950 MHz, A_IN = –36 dBFS,
IMD = 92 dBFS

Figure 18. FFT for Two-Tone Input Signal
(–36 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.77 GHz, f_IN2 = 1.790 GHz, A_IN = –36 dBFS,
IMD = 94 dBFS

Figure 20. FFT for Two-Tone Input Signal (–36 dBFS)

f_IN1 = 1.77 GHz, f_IN2 = 1.790 GHz, A_IN = –36 dBFS,
IMD = 92 dBFS

Figure 22. FFT for Two-Tone Input Signal
(–36 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.8 GHz, f_IN2 = 2.6 GHz, A_IN = –36 dBFS, IMD = 95 dBFS

Figure 24. FFT for Two-Tone Input Signal (–36 dBFS)

f_IN1 = 2.09 MHz, f_IN2 = 2.1 GHz, A_IN = –36 dBFS,
IMD = 92 dBFS

Figure 26. FFT for Two-Tone Input Signal
(–36 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 3.49 GHz, f_IN2 = 3.51 GHz, IMD = 95 dBFS,
A_IN = –36 dBFS with 2-dB gain

Figure 28. FFT for Two-Tone Input Signal (–36 dBFS)

f_IN1 = 2.59 GHz, f_IN2 = 2.6 GHz, A_IN = –36 dBFS,
IMD = 92 dBFS

Figure 30. FFT for Two-Tone Input Signal
(–36 dBFS, f_S = 2457.6 MSPS)

f_IN1 = 1.77 GHz, f_IN2 = 1.79 GHz

Figure 32. Intermodulation Distortion vs Input Amplitude (1770 MHz and 1790 MHz, f_S = 2457.6 MSPS)

f_IN1 = 2.09 GHz, f_IN2 = 2.1 GHz

Figure 34. Intermodulation Distortion vs Input Amplitude (2090 MHz and 2100 MHz, f_S = 2457.6 MSPS)

f_IN1 = 2.59GHz, f_IN2 = 2.61 GHz

Figure 36. Intermodulation Distortion vs Input Amplitude (2590 MHz and 2600 MHz, f_S = 2457.6 MSPS)

Figure 38. Spurious-Free Dynamic Range vs
Input Frequency (f_S = 2457.6 MSPS)

Figure 40. IL Spur vs Input Frequency (f_S = 2457.6 MSPS)

Figure 42. Signal-to-Noise Ratio vs Input Frequency
(f_S = 2457.6 MSPS)

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 44. Spurious-Free Dynamic Range vs
AVDD Supply and Temperature

f_IN = 3.5GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 46. Spurious-Free Dynamic Range vs
AVDD Supply and Temperature

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 48. Spurious-Free Dynamic Range vs
DVDD Supply and Temperature

f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 50. Spurious-Free Dynamic Range vs
DVDD Supply and Temperature

f_IN = 1.85 GHz, A_IN = –2 dBFS

Figure 52. Spurious-Free Dynamic Range vs
AVDD19 Supply and Temperature

f_IN = 3.5 GHz, A_IN = –3 dBFS with 2-dB digital gain

Figure 54. Spurious-Free Dynamic Range vs
AVDD19 Supply and Temperature

f_IN = 1.78 GHz, A_OUT = –2 dBFS

Figure 56. HD2 Histogram at AVDD19 = 1.9 V

f_IN = 1.78 GHz

Figure 58. Performance vs Amplitude

f_IN = 1.78 GHz, A_IN = –2 dBFS

Figure 60. Performance vs Clock Amplitude

f_IN = 1.78 GHz

Figure 62. Performance vs Clock Duty Cycle

f_IN = 1.8 GHz, A_IN = –2 dBFS, PSRR = 37 dB,
f_PSRR = 3 MHz, A_PSRR = 50 mV_PP, AVDD = 1.9 V

Figure 64. Power-Supply Rejection Ratio FFT for
Test Signal on AVDD Supply

f_CMRR = 10 MHz, A_PSRR = 50 mV_PP, CMRR = 32 dB

Figure 66. Common-Mode Rejection Ratio FFT

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 60.6 dBFS, SFDR (includes IL) = 75 dBc

Figure 68. FFT in 4x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 62.6 dBFS, SFDR (includes IL) = 86 dBc

Figure 70. FFT in 8x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 63.3 dBFS, SFDR (includes IL) = 81 dBc

Figure 72. FFT in 10x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 63.9 dBFS, SFDR (includes IL) = 83 dBc

Figure 74. FFT in 16x Decimation (Complex Output)

f_IN = 1.78 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 64.4 dBFS, SFDR (includes IL) = 84 dBc

Figure 76. FFT in 20x Decimation (Complex Output)

f_IN = 1.8 GHz, A_IN = –2 dBFS, f_S = 2949.12 MSPS,
SNR = 64.5 dBFS, SFDR (includes IL) = 79 dBc

Figure 78. FFT in 32x Decimation (Complex Output)

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）

サーマルパッド・メカニカル・データ

発注情報

6 Specifications

6.1 Absolute Maximum Ratings

6.2 ESD Ratings

6.3 Recommended Operating Conditions

6.4 Thermal Information

6.5 Electrical Characteristics

6.6 AC Performance Characteristics: f_S = 2949.12 MSPS

6.7 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A + D Band⁽¹⁾)

6.8 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A Band⁽¹⁾)

6.9 Digital Requirements

6.10 Timing Requirements

6.11 Typical Characteristics

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）

サーマルパッド・メカニカル・データ

発注情報

6 Specifications

6.1 Absolute Maximum Ratings

6.2 ESD Ratings

6.3 Recommended Operating Conditions

6.4 Thermal Information

6.5 Electrical Characteristics

6.6 AC Performance Characteristics: fS = 2949.12 MSPS

6.7 AC Performance Characteristics: fS = 2457.6 MSPS (Performance Optimized for F + A + D Band(1))

6.8 AC Performance Characteristics: fS = 2457.6 MSPS (Performance Optimized for F + A Band(1))

6.9 Digital Requirements

6.10 Timing Requirements

6.11 Typical Characteristics

6.6 AC Performance Characteristics: f_S = 2949.12 MSPS

6.7 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A + D Band⁽¹⁾)

6.8 AC Performance Characteristics: f_S = 2457.6 MSPS
(Performance Optimized for F + A Band⁽¹⁾)