JAJSIU8B June   2015  – April 2020 ADS131E08S

PRODUCTION DATA.  

1. 1 特長
2. 2 アプリケーション
   1.     電源アプリケーション：3 相電圧および電流の接続
3. 3 説明
4. 4 改訂履歴
5. 5 Device Comparison
6. 6 Pin Configuration and Functions
   1.     Pin Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 Timing Requirements
   7. 7.7 Switching Characteristics
   8. 7.8 Typical Characteristics
8. 8 Parameter Measurement Information
   1. 8.1 Noise Measurements
9. 9 Detailed Description
   1. 9.1 Overview
   2. 9.2 Functional Block Diagram
   3. 9.3 Feature Description
      1. 9.3.1  Electromagnetic Interference (EMI) Filter
      2. 9.3.2  Input Multiplexer
         1. 9.3.2.1 Device Noise Measurements
         2. 9.3.2.2 Test Signals (TestP and TestN)
         3. 9.3.2.3 Temperature Sensor (TempP, TempN)
         4. 9.3.2.4 Power-Supply Measurements (MVDDP, MVDDN)
      3. 9.3.3  Analog Input
      4. 9.3.4  PGA Settings and Input Range
         1. 9.3.4.1 Input Common-Mode Range
      5. 9.3.5  ΔΣ Modulator
      6. 9.3.6  Clock
      7. 9.3.7  Digital Decimation Filter
      8. 9.3.8  Voltage Reference
      9. 9.3.9  Input Out-of-Range Detection
      10. 9.3.10 General-Purpose Digital I/O (GPIO)
   4. 9.4 Device Functional Modes
      1. 9.4.1 Power-Down
      2. 9.4.2 Reset
      3. 9.4.3 Conversion Mode
         1. 9.4.3.1 START Pin Low-to-High Transition or START Command Sent
         2. 9.4.3.2 Input Signal Step
         3. 9.4.3.3 Continuous Conversion Mode
   5. 9.5 Programming
      1. 9.5.1 SPI Interface
         1. 9.5.1.1 Chip Select (CS)
         2. 9.5.1.2 Serial Clock (SCLK)
         3. 9.5.1.3 Data Input (DIN)
         4. 9.5.1.4 Data Output (DOUT)
         5. 9.5.1.5 Data Ready (DRDY)
      2. 9.5.2 Data Retrieval
         1. 9.5.2.1 Status Word
         2. 9.5.2.2 Readback Length
         3. 9.5.2.3 Data Format
      3. 9.5.3 SPI Command Definitions
         1. 9.5.3.1  WAKEUP: Exit STANDBY Mode
         2. 9.5.3.2  STANDBY: Enter STANDBY Mode
         3. 9.5.3.3  RESET: Reset Registers to Default Values
         4. 9.5.3.4  START: Start Conversions
         5. 9.5.3.5  STOP: Stop Conversions
         6. 9.5.3.6  OFFSETCAL: Channel Offset Calibration
         7. 9.5.3.7  RDATAC: Start Read Data Continuous Mode
         8. 9.5.3.8  SDATAC: Stop Read Data Continuous Mode
         9. 9.5.3.9  RDATA: Read Data
         10. 9.5.3.10 RREG: Read from Register
         11. 9.5.3.11 WREG: Write to Register
         12. 9.5.3.12 Sending Multibyte Commands
   6. 9.6 Register Map
      1. 9.6.1 Register Descriptions
         1. 9.6.1.1 ID: ID Control Register (Factory-Programmed, Read-Only) (address = 00h) [reset = D2h]
            1. Table 11. ID: ID Control Register Field Descriptions
         2. 9.6.1.2 CONFIG1: Configuration Register 1 (address = 01h) [reset = 94h]
            1. Table 12. CONFIG1: Configuration Register 1 Field Descriptions
         3. 9.6.1.3 CONFIG2: Configuration Register 2 (address = 02h) [reset = 00h]
            1. Table 14. CONFIG2: Configuration Register 2 Field Descriptions
         4. 9.6.1.4 CONFIG3: Configuration Register 3 (address = 03h) [reset = E0h]
            1. Table 15. CONFIG3: Configuration Register 3 Field Descriptions
         5. 9.6.1.5 FAULT: Fault Detect Control Register (address = 04h) [reset = 00h]
            1. Table 16. FAULT: Fault Detect Control Register Field Descriptions
         6. 9.6.1.6 CHnSET: Individual Channel Settings (address = 05h to 0Ch) [reset = 10h]
            1. Table 17. CHnSET: Individual Channel Settings Field Descriptions
         7. 9.6.1.7 FAULT_STATP: Fault Detect Positive Input Status (address = 12h) [reset = 00h]
            1. Table 18. FAULT_STATP: Fault Detect Positive Input Status Field Descriptions
         8. 9.6.1.8 FAULT_STATN: Fault Detect Negative Input Status (address = 13h) [reset = 00h]
            1. Table 19. FAULT_STATN: Fault Detect Negative Input Status Field Descriptions
         9. 9.6.1.9 GPIO: General-Purpose IO Register (address = 14h) [reset = 0Fh]
            1. Table 20. GPIO: General-Purpose IO Register Field Descriptions
10. 10Application and Implementation
    1. 10.1 Application Information
       1. 10.1.1 Multiple Device Configuration
          1. 10.1.1.1 Synchronizing Multiple Devices
          2. 10.1.1.2 Standard Configuration
          3. 10.1.1.3 Daisy-Chain Configuration
       2. 10.1.2 Power Monitoring Specific Applications
       3. 10.1.3 Current Sensing
       4. 10.1.4 Voltage Sensing
    2. 10.2 Typical Application
       1. 10.2.1 Design Requirements
       2. 10.2.2 Detailed Design Procedure
       3. 10.2.3 Application Curves
    3. 10.3 Initialization Set Up
       1. 10.3.1 Setting the Device Up for Basic Data Capture
11. 11Power Supply Recommendations
    1. 11.1 Power-Up Timing
    2. 11.2 Recommended External Capacitor Values
    3. 11.3 Device Connections for Unipolar Power Supplies
    4. 11.4 Device Connections for Bipolar Power Supplies
12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
13. 13デバイスおよびドキュメントのサポート
    1. 13.1 ドキュメントのサポート
       1. 13.1.1 関連資料
    2. 13.2 サポート・リソース
    3. 13.3 商標
    4. 13.4 静電気放電に関する注意事項
    5. 13.5 Glossary
14. 14メカニカル、パッケージ、および注文情報