JAJSE21B October   2017  – November 2018

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     代表的なアプリケーション回路
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Undervoltage Lockout (UVLO)
      2. 9.3.2 Power On
      3. 9.3.3 Overvoltage Protection (OVP)
      4. 9.3.4 Dynamic Power-path Management
        1. 9.3.4.1 Input Source Connected (Adapter or USB)
          1. 9.3.4.1.1 Input DPM Mode (VIN-DPM)
          2. 9.3.4.1.2 DPPM Mode
          3. 9.3.4.1.3 Battery Supplement Mode
        2. 9.3.4.2 Input Source Not Connected
      5. 9.3.5 Battery Charging
        1. 9.3.5.1 Charge Current Translator
        2. 9.3.5.2 Battery Detection And Recharge
        3. 9.3.5.3 Battery Disconnect (SYSOFF Input)
        4. 9.3.5.4 Dynamic Charge Timers (TMR Input)
        5. 9.3.5.5 Status Indicators (PGOOD, CHG)
        6. 9.3.5.6 Thermal Regulation And Thermal Shutdown
      6. 9.3.6 Battery Pack Temperature Monitoring
      7. 9.3.7 Half-Wave Adaptors
    4. 9.4 Device Functional Modes
      1. 9.4.1 Sleep Mode
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application – bq24079QW-Q1 Charger Design Example
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Calculations
          1. 10.2.2.1.1 Program the Fast Charge Current (ISET):
          2. 10.2.2.1.2 Program the Input Current Limit (ILIM)
          3. 10.2.2.1.3 Program 6.25-hour Fast-Charge Safety Timer (TMR)
        2. 10.2.2.2 TS Function
        3. 10.2.2.3 CHG and PGOOD
        4. 10.2.2.4 System ON/OFF (SYSOFF)
        5. 10.2.2.5 Selecting In, Out And Bat Pin Capacitors
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
    3. 12.3 Thermal Package
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 デバイス・サポート
      1. 13.1.1 デベロッパー・ネットワークの製品に関する免責事項
    2. 13.2 ドキュメントのサポート
      1. 13.2.1 関連資料
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 コミュニティ・リソース
    5. 13.5 商標
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • RGT|16
サーマルパッド・メカニカル・データ
発注情報

9.3.5.5 Status Indicators (PGOOD, CHG)

The bq24079QW-Q1 contains two open-drain outputs that signal its status. The PGOOD output signals when a valid input source is connected. PGOOD is low when (VBAT + VIN(DT)) < VIN < VOVP. When the input voltage is outside of this range, PGOOD is high impedance.

The charge cycle after power-up, CE going low or exiting OVP is indicated with the CHG pin on (low - LED on), whereas all refresh (subsequent) charges will result in the CHG pin off (open - LED off). In addition, the CHG signals timer faults by flashing at approximately 2 Hz.

Table 1. PGOOD Status Indicator

INPUT STATE PGOOD OUTPUT
VIN < VUVLO Hi impedance
VUVLO < VIN < VBAT + VIN(DT) Hi impedance
VBAT + VIN(DT) < VIN < VOVP Low
VIN > VOVP Hi impedance

Table 2. CHG Status Indicator

CHARGE STATE CHG OUTPUT
Charging Low (for first charge cycle)
Charging suspended by thermal loop
Safety timers expired Flashing at 2Hz
Charging done Hi impedance
Recharging after termination
IC disabled or no valid input power
Battery absent