JAJSD77A May   2017  – May 2018

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      アプリケーション図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Power-Up from Battery Without DC Source
      2. 8.3.2 Power-Up From DC Source
        1. 8.3.2.1 CHRG_OK Indicator
        2. 8.3.2.2 Input Voltage and Current Limit Setup
        3. 8.3.2.3 Battery Cell Configuration
        4. 8.3.2.4 Device Hi-Z State
      3. 8.3.3 USB On-The-Go (OTG)
      4. 8.3.4 Converter Operation
        1. 8.3.4.1 Inductor Setting through IADPT Pin
        2. 8.3.4.2 Continuous Conduction Mode (CCM)
        3. 8.3.4.3 Pulse Frequency Modulation (PFM)
      5. 8.3.5 Current and Power Monitor
        1. 8.3.5.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 8.3.5.2 High-Accuracy Power Sense Amplifier (PSYS)
      6. 8.3.6 Input Source Dynamic Power Manage
      7. 8.3.7 Two-Level Adapter Current Limit (Peak Power Mode)
      8. 8.3.8 Processor Hot Indication
        1. 8.3.8.1 PROCHOT During Low Power Mode
        2. 8.3.8.2 PROCHOT Status
      9. 8.3.9 Device Protection
        1. 8.3.9.1 Watchdog Timer
        2. 8.3.9.2 Input Overvoltage Protection (ACOV)
        3. 8.3.9.3 Input Overcurrent Protection (ACOC)
        4. 8.3.9.4 System Overvoltage Protection (SYSOVP)
        5. 8.3.9.5 Battery Overvoltage Protection (BATOVP)
        6. 8.3.9.6 Battery Short
        7. 8.3.9.7 Thermal Shutdown (TSHUT)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Forward Mode
        1. 8.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 8.4.1.2 Battery Charging
      2. 8.4.2 USB On-The-Go
    5. 8.5 Programming
      1. 8.5.1 SMBus Interface
        1. 8.5.1.1 SMBus Write-Word and Read-Word Protocols
        2. 8.5.1.2 Timing Diagrams
    6. 8.6 Register Map
      1. 8.6.1  Setting Charge and PROCHOT Options
        1. 8.6.1.1 ChargeOption0 Register (SMBus address = 12h) [reset = E20Eh]
          1. Table 7. ChargeOption0 Register (SMBus address = 12h) Field Descriptions
          2. Table 8. ChargeOption0 Register (SMBus address = 12h) Field Descriptions
        2. 8.6.1.2 ChargeOption1 Register (SMBus address = 30h) [reset = 211h]
          1. Table 9.  ChargeOption1 Register (SMBus address = 30h) Field Descriptions
          2. Table 10. ChargeOption1 Register (SMBus address = 30h) Field Descriptions
        3. 8.6.1.3 ChargeOption2 Register (SMBus address = 31h) [reset = 2B7]
          1. Table 11. ChargeOption2 Register (SMBus address = 31h) Field Descriptions
          2. Table 12. ChargeOption2 Register (SMBus address = 31h) Field Descriptions
        4. 8.6.1.4 ChargeOption3 Register (SMBus address = 32h) [reset = 0h]
          1. Table 13. ChargeOption3 Register (SMBus address = 32h) Field Descriptions
          2. Table 14. ChargeOption3 Register (SMBus address = 32h) Field Descriptions
        5. 8.6.1.5 ProchotOption0 Register (SMBus address = 33h) [reset = 04A54h]
          1. Table 15. ProchotOption0 Register (SMBus address = 33h) Field Descriptions
          2. Table 16. ProchotOption0 Register (SMBus address = 33h) Field Descriptions
        6. 8.6.1.6 ProchotOption1 Register (SMBus address = 34h) [reset = 8120h]
          1. Table 17. ProchotOption1 Register (SMBus address = 34h) Field Descriptions
          2. Table 18. ProchotOption1 Register (SMBus address = 34h) Field Descriptions
        7. 8.6.1.7 ADCOption Register (SMBus address = 35h) [reset = 2000h]
          1. Table 19. ADCOption Register (SMBus address = 35h) Field Descriptions
          2. Table 20. ADCOption Register (SMBus address = 35h) Field Descriptions
      2. 8.6.2  Charge and PROCHOT Status
        1. 8.6.2.1 ChargerStatus Register (SMBus address = 20h) [reset = 0000h]
          1. Table 21. ChargerStatus Register (SMBus address = 20h) Field Descriptions
          2. Table 22. ChargerStatus Register (SMBus address = 20h) Field Descriptions
        2. 8.6.2.2 ProchotStatus Register (SMBus address = 21h) [reset = 0h]
          1. Table 23. ProchotStatus Register (SMBus address = 21h) Field Descriptions
          2. Table 24. ProchotStatus Register (SMBus address = 21h) Field Descriptions
      3. 8.6.3  ChargeCurrent Register (SMBus address = 14h) [reset = 0h]
        1. Table 25. Charge Current Register (14h) With 10-mΩ Sense Resistor (SMBus address = 14h) Field Descriptions
        2. Table 26. Charge Current Register (14h) With 10-mΩ Sense Resistor (SMBus address = 14h) Field Descriptions
        3. 8.6.3.1   Battery Pre-Charge Current Clamp
      4. 8.6.4  MaxChargeVoltage Register (SMBus address = 15h) [reset value based on CELL_BATPRESZ pin setting]
        1. Table 27. MaxChargeVoltage Register (SMBus address = 15h) Field Descriptions
        2. Table 28. MaxChargeVoltage Register (SMBus address = 15h) Field Descriptions
      5. 8.6.5  MinSystemVoltage Register (SMBus address = 3Eh) [reset value based on CELL_BATPRESZ pin setting]
        1. Table 29. MinSystemVoltage Register (SMBus address = 3Eh) Field Descriptions
        2. Table 30. MinSystemVoltage Register (SMBus address = 3Eh) Field Descriptions
        3. 8.6.5.1   System Voltage Regulation
      6. 8.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 8.6.6.1 Input Current Registers
          1. 8.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (SMBus address = 3Fh) [reset = 4000h]
            1. Table 31. IIN_HOST Register With 10-mΩ Sense Resistor (SMBus address = 3Fh) Field Descriptions
            2. Table 32. IIN_HOST Register With 10-mΩ Sense Resistor (SMBus address = 3Fh) Field Descriptions
          2. 8.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (SMBus address = 022h) [reset = 0h]
            1. Table 33. IIN_DPM Register With 10-mΩ Sense Resistor (SMBus address = 022h) Field Descriptions
            2. Table 34. IIN_DPM Register With 10-mΩ Sense Resistor (SMBus address = 022h) Field Descriptions
          3. 8.6.6.1.3 InputVoltage Register (SMBus address = 3Dh) [reset = VBUS-1.28V]
            1. Table 35. InputVoltage Register (SMBus address = 3Dh) Field Descriptions
            2. Table 36. InputVoltage Register (SMBus address = 3Dh) Field Descriptions
      7. 8.6.7  OTGVoltage Register (SMBus address = 3Bh) [reset = 0h]
        1. Table 37. OTGVoltage Register (SMBus address = 3Bh) Field Descriptions
        2. Table 38. OTGVoltage Register (SMBus address = 3Bh) Field Descriptions
      8. 8.6.8  OTGCurrent Register (SMBus address = 3Ch) [reset = 0h]
        1. Table 39. OTGCurrent Register (SMBus address = 3Ch) Field Descriptions
        2. Table 40. OTGCurrent Register (SMBus address = 3Ch) Field Descriptions
      9. 8.6.9  ADCVBUS/PSYS Register (SMBus address = 23h)
        1. Table 41. ADCVBUS/PSYS Register Field Descriptions
      10. 8.6.10 ADCIBAT Register (SMBus address = 24h)
        1. Table 42. ADCIBAT Register Field Descriptions
      11. 8.6.11 ADCIINCMPIN Register (SMBus address = 25h)
        1. Table 43. ADCIINCMPIN Register Field Descriptions
      12. 8.6.12 ADCVSYSVBAT Register (SMBus address = 26h)
        1. Table 44. ADCVSYSVBAT Register Field Descriptions
      13. 8.6.13 ID Registers
        1. 8.6.13.1 ManufactureID Register (SMBus address = FEh) [reset = 0040h]
          1. Table 45. ManufactureID Register Field Descriptions
        2. 8.6.13.2 Device ID (DeviceAddress) Register (SMBus address = FFh) [reset = 0h]
          1. Table 46. Device ID (DeviceAddress) Register Field Descriptions
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 ACP-ACN Input Filter
        2. 9.2.2.2 Inductor Selection
        3. 9.2.2.3 Input Capacitor
        4. 9.2.2.4 Output Capacitor
        5. 9.2.2.5 Power MOSFETs Selection
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
      1. 11.2.1 Layout Consideration of Current Path
      2. 11.2.2 Layout Consideration of Short Circuit Protection
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デベロッパー・ネットワークの製品に関する免責事項
    2. 12.2 ドキュメントのサポート
      1. 12.2.1 関連資料
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 コミュニティ・リソース
    5. 12.5 商標
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.6.4 MaxChargeVoltage Register (SMBus address = 15h) [reset value based on CELL_BATPRESZ pin setting]

To set the output charge voltage, write a 16-bit ChargeVoltage register command (REG0x15()) using the data format listed in Table 27 and Table 28. The charger provides charge voltage range from 1.024 V to 19.200 V, with 16-mV step resolution. Any write below 1.024 V or above 19.200 V is ignored. Upon POR or when charge is disabled, the system is regulated at the MaxChargeVoltage register.

Upon POR, REG0x15() is by default set as 4192 mV for 1 s, 8400 mV for 2 s, 12592 mV for 3 s or 16800 mV for 4 s. After CHRG_OK, if host writes REG0x14() before REG0x15(), the charge will start after the write to REG0x14().If the battery is different from 4.2 V/cell, the host has to write to REG0x15() before REG0x14() for correct battery voltage setting. Writing REG0x15() to 0 will set REG0x15() to default value on CELL_BATPRESZ pin, and force REG0x14() to zero to disable charge.

The SRN pin is used to sense the battery voltage for voltage regulation and should be connected as close to the battery as possible, and directly place a decoupling capacitor (0.1 µF recommended) as close to the device as possible to decouple high frequency noise.

Figure 27. MaxChargeVoltage Register (SMBus address = 15h) [reset value based on CELL_BATPRESZ pin setting]
15 14 13 12 11 10 9 8
Reserved Max Charge Voltage, bit 10 Max Charge Voltage, bit 9 Max Charge Voltage, bit 8 Max Charge Voltage, bit 7 Max Charge Voltage, bit 6 Max Charge Voltage, bit 5 Max Charge Voltage, bit 4
R/W R/W R/W R/W R/W R/W R/W R/W
7 6 5 4 3 2 1 0
Max Charge Voltage, bit 3 Max Charge Voltage, bit 2 Max Charge Voltage, bit 1 Max Charge Voltage, bit 0 Reserved
R/W R/W R/W R/W R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

Table 27. MaxChargeVoltage Register (SMBus address = 15h) Field Descriptions

SMBus
BIT		 FIELD TYPE RESET DESCRIPTION
15 Reserved R/W 0b

Not used. 1 = invalid write.

14 Max Charge Voltage, bit 10 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 16384 mV of charger voltage.
13 Max Charge Voltage, bit 9 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 8192 mV of charger voltage
12 Max Charge Voltage, bit 8 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 4096 mV of charger voltage.
11 Max Charge Voltage, bit 7 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 2048 mV of charger voltage.
10 Max Charge Voltage, bit 6 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 1024 mV of charger voltage.
9 Max Charge Voltage, bit 5 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 512 mV of charger voltage.
8 Max Charge Voltage, bit 4 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 256 mV of charger voltage.

Table 28. MaxChargeVoltage Register (SMBus address = 15h) Field Descriptions

SMBus
BIT		 FIELD TYPE RESET DESCRIPTION
7 Max Charge Voltage, bit 3 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 128 mV of charger voltage.
6 Max Charge Voltage, bit 2 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 64 mV of charger voltage.
5 Max Charge Voltage, bit 1 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 32 mV of charger voltage.

4 Max Charge Voltage, bit 0 R/W 0b

0 = Adds 0 mV of charger voltage.

1 = Adds 16 mV of charger voltage.
3-0 Reserved R/W 0000b

Not used. Value Ignored.