JAJSFQ9C june   2018  – may 2023 BQ25713 , BQ25713B

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 概要 (続き)
  7. 6 Device Comparison Table
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up from Battery Without DC Source
      2. 9.3.2  Vmin Active Protection (VAP) when Battery only Mode
      3. 9.3.3  Power-Up From DC Source
        1. 9.3.3.1 CHRG_OK Indicator
        2. 9.3.3.2 Input Voltage and Current Limit Setup
        3. 9.3.3.3 Battery Cell Configuration
        4. 9.3.3.4 Device Hi-Z State
      4. 9.3.4  USB On-The-Go (OTG)
      5. 9.3.5  Converter Operation
        1. 9.3.5.1 Inductance Detection Through IADPT Pin
        2. 9.3.5.2 Continuous Conduction Mode (CCM)
        3. 9.3.5.3 Pulse Frequency Modulation (PFM)
      6. 9.3.6  Current and Power Monitor
        1. 9.3.6.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.6.2 High-Accuracy Power Sense Amplifier (PSYS)
      7. 9.3.7  Input Source Dynamic Power Manage
      8. 9.3.8  Two-Level Adapter Current Limit (Peak Power Mode)
      9. 9.3.9  Processor Hot Indication
        1. 9.3.9.1 PROCHOT During Low Power Mode
        2. 9.3.9.2 PROCHOT Status
      10. 9.3.10 Device Protection
        1. 9.3.10.1 Watchdog Timer
        2. 9.3.10.2 Input Overvoltage Protection (ACOV)
        3. 9.3.10.3 Input Overcurrent Protection (ACOC)
        4. 9.3.10.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.10.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.10.6 Battery Short
        7. 9.3.10.7 System Short Hiccup Mode
        8. 9.3.10.8 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
        1. 9.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 9.4.1.2 Battery Charging
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)
    5. 9.5 Programming
      1. 9.5.1 I2C Serial Interface
        1. 9.5.1.1 Data Validity
        2. 9.5.1.2 START and STOP Conditions
        3. 9.5.1.3 Byte Format
        4. 9.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 9.5.1.5 Slave Address and Data Direction Bit
        6. 9.5.1.6 Single Read and Write
        7. 9.5.1.7 Multi-Read and Multi-Write
        8. 9.5.1.8 Write 2-Byte I2C Commands
    6. 9.6 Register Map
      1. 9.6.1  Setting Charge and PROCHOT Options
        1. 9.6.1.1 ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
        2. 9.6.1.2 ChargeOption1 Register (I2C address = 31/30h) [reset = 0211h]
        3. 9.6.1.3 ChargeOption2 Register (I2C address = 33/32h) [reset = 02B7h]
        4. 9.6.1.4 ChargeOption3 Register (I2C address = 35/34h) [reset = 0030h]
        5. 9.6.1.5 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A65h]
        6. 9.6.1.6 ProchotOption1 Register (I2C address = 39/38h) [reset = 81A0h]
        7. 9.6.1.7 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      2. 9.6.2  Charge and PROCHOT Status
        1. 9.6.2.1 ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
        2. 9.6.2.2 ProchotStatus Register (I2C address = 23/22h) [reset = A800h]
      3. 9.6.3  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 9.6.3.1 Battery Precharge Current Clamp
      4. 9.6.4  MaxChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      5. 9.6.5  MinSystemVoltage Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
        1. 9.6.5.1 System Voltage Regulation
      6. 9.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 9.6.6.1 Input Current Registers
          1. 9.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (I2C address = 0F/0Eh) [reset = 4100h]
          2. 9.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (I2C address = 25/24h) [reset = 4100h]
          3. 9.6.6.1.3 InputVoltage Register (I2C address = 0B/0Ah) [reset = VBUS-1.28V]
      7. 9.6.7  OTGVoltage Register (I2C address = 07/06h) [reset = 0000h]
      8. 9.6.8  OTGCurrent Register (I2C address = 09/08h) [reset = 0000h]
      9. 9.6.9  ADCVBUS/PSYS Register (I2C address = 27/26h)
      10. 9.6.10 ADCIBAT Register (I2C address = 29/28h)
      11. 9.6.11 ADCIINCMPIN Register (I2C address = 2B/2Ah)
      12. 9.6.12 ADCVSYSVBAT Register (I2C address = 2D/2Ch)
      13. 9.6.13 ID Registers
        1. 9.6.13.1 ManufactureID Register (I2C address = 2Eh) [reset = 0040h]
        2. 9.6.13.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = 0h]
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 ACP-ACN Input Filter
        2. 10.2.2.2 Inductor Selection
        3. 10.2.2.3 Input Capacitor
        4. 10.2.2.4 Output Capacitor
        5. 10.2.2.5 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 サード・パーティ製品に関する免責事項
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 サポート・リソース
    5. 13.5 Trademarks
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 用語集
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.6.2.2 ProchotStatus Register (I2C address = 23/22h) [reset = A800h]

Figure 9-20 ProchotStatus Register (I2C address = 23/22h) [reset = A800h]
76543210
ReservedEN_PROCHOT
_EXIT		PROCHOT_WIDTHPROCHOT
_CLEAR		ReservedSTAT_VAP
_FAIL		STAT_EXIT
_VAP
RR/WR/WR/WRR/WR/W
76543210
STAT_VDPMSTAT_COMPSTAT_ICRITSTAT_INOMSTAT_IDCHGSTAT_VSYSSTAT_BAT
_Removal		STAT_ADPT
_Removal
R/WRRRRRRR
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-21 ProchotStatus Register (I2C address = 23h) Field Descriptions
I2C
23h		FIELDTYPERESETDESCRIPTION
7ReservedR1b

Reserved

6EN_PROCHOT _EXITR/W0b

PROCHOT Pulse Extension Enable. When pulse extension is enabled, keep the PROCHOT pin voltage LOW until host writes REG0x23[3] = 0.

0b: Disable pulse extension <default at POR>

1b: Enable pulse extension

5-4PROCHOT _WIDTHR/W10b

PROCHOT Pulse Width.

Minimum PROCHOT pulse width when REG0x23[6] = 0

00b: 100 us

01b: 1 ms

10b: 10 ms <default at POR>

11b: 5 ms

3PROCHOT _CLEARR/W1b

PROCHOT Pulse Clear.

Clear PROCHOT pulse when 0x23[6] = 1.

0b: Clear PROCHOT pulse and drive PROCHOT pin HIGH

1b: Idle <default at POR>

2ReservedR0bReserved
1STAT_VAP_FAILR/W0b

This status bit reports a failure to load VBUS 7 consecutive times in VAP mode, which indicates the battery voltage might be not high enough to enter VAP mode, or the VAP loading current settings are too high.

0b: Not is VAP failure <default at POR>

1b: In VAP failure, the charger exits VAP mode, and latches off until the host writes this bit to 0.

0STAT_EXIT_VAPR/W0b

When the charger is operated in VAP mode, it can exit VAP by either being disabled through host, or there is any charger faults.

0b: PROCHOT_EXIT_VAP is not active <default at POR>

1b: PROCHOT_EXIT_VAP is active, PROCHOT pin is low until host writes this status bit to 0.

Table 9-22 ProchotStatus Register (I2C address = 22h) Field Descriptions
I2C
22h		FIELDTYPERESETDESCRIPTION
7STAT_VDPMR/W0b

0b: Not triggered

1b: Triggered

6STAT_COMPR0b

0b: Not triggered

1b: Triggered

5STAT_ICRITR0b

0b: Not triggered

1b: Triggered

4STAT_INOMR0b

0b: Not triggered

1b: Triggered

3STAT_IDCHGR0b

0b: Not triggered

1b: Triggered

2STAT_VSYSR0b

0b: Not triggered

1b: Triggered

1STAT_Battery_RemovalR0b

0b: Not triggered

1b: Triggered

0STAT_Adapter_RemovalR0b

0b: Not triggered

1b: Triggered