JAJSNA7A November   2021  – February 2022 BQ27Z746

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configurations and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
      1. 6.5.1 Supply Current
      2. 6.5.2 Common Analog (LDO, LFO, HFO, REF1, REF2, I-WAKE)
      3. 6.5.3 Battery Protection (CHG, DSG)
      4. 6.5.4 Cell Sensing Output (BAT_SP, BAT_SN)
      5. 6.5.5 Gauge Measurements (ADC, CC, Temperature)
      6. 6.5.6 Flash Memory
    6. 6.6 Digital I/O: DC Characteristics
    7. 6.7 Digital I/O: Timing Characteristics
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  BQ27Z746 Processor
      2. 7.3.2  Battery Parameter Measurements
        1. 7.3.2.1 Coulomb Counter (CC) and Digital Filter
        2. 7.3.2.2 ADC Multiplexer
        3. 7.3.2.3 Analog-to-Digital Converter (ADC)
        4. 7.3.2.4 Internal Temperature Sensor
        5. 7.3.2.5 External Temperature Sensor Support
      3. 7.3.3  Power Supply Control
      4. 7.3.4  Bus Communication Interface
      5. 7.3.5  Low Frequency Oscillator
      6. 7.3.6  High Frequency Oscillator
      7. 7.3.7  1.8-V Low Dropout Regulator
      8. 7.3.8  Internal Voltage References
      9. 7.3.9  Overcurrent in Discharge Protection
      10. 7.3.10 Overcurrent in Charge Protection
      11. 7.3.11 Short-Circuit Current in Discharge Protection
      12. 7.3.12 Primary Protection Features
      13. 7.3.13 Battery Sensing
      14. 7.3.14 Gas Gauging
      15. 7.3.15 Zero Volt Charging (ZVCHG)
      16. 7.3.16 Charge Control Features
      17. 7.3.17 Authentication
    4. 7.4 Device Functional Modes
      1. 7.4.1 Lifetime Logging Features
      2. 7.4.2 Configuration
        1. 7.4.2.1 Coulomb Counting
        2. 7.4.2.2 Cell Voltage Measurements
        3. 7.4.2.3 Auto Calibration
        4. 7.4.2.4 Temperature Measurements
  8. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements (Default)
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Changing Design Parameters
      3. 8.2.3 Calibration Process
      4. 8.2.4 Gauging Data Updates
        1. 8.2.4.1 Application Curve
  9. 9 Power Supply Requirements
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 サポート・リソース
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Orderable, and Packaging Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.2.5 External Temperature Sensor Support

The TS input is enabled with an internal 18-kΩ (Typ.) linearization pull-up resistor to support the use of a 10-kΩ (25°C) NTC external thermistor, such as the Semitec 103AT-2. The NTC thermistor should be connected between VSS and the individual TS pin. The analog measurement is then taken by the ADC through its input multiplexer. If a different thermistor type is required, then changes to configurations may be required.

GUID-2B12769F-05C6-4552-8762-6F957836DBFF-low.gifFigure 7-1 External Thermistor Biasing