JAJSLK7D January   2015  – April 2021 BQ34Z100-G1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: Power-On Reset
    6. 6.6  Electrical Characteristics: LDO Regulator
    7. 6.7  Electrical Characteristics: Internal Temperature Sensor Characteristics
    8. 6.8  Electrical Characteristics: Low-Frequency Oscillator
    9. 6.9  Electrical Characteristics: High-Frequency Oscillator
    10. 6.10 Electrical Characteristics: Integrating ADC (Coulomb Counter) Characteristics
    11. 6.11 Electrical Characteristics: ADC (Temperature and Cell Measurement) Characteristics
    12. 6.12 Electrical Characteristics: Data Flash Memory Characteristics
    13. 6.13 Timing Requirements: HDQ Communication
    14. 6.14 Timing Requirements: I2C-Compatible Interface
    15. 6.15 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Data Commands
        1. 7.3.1.1  Standard Data Commands
        2. 7.3.1.2  Control(): 0x00/0x01
          1. 7.3.1.2.1  CONTROL_STATUS: 0x0000
          2. 7.3.1.2.2  DEVICE TYPE: 0x0001
          3. 7.3.1.2.3  FW_VERSION: 0x0002
          4. 7.3.1.2.4  HW_VERSION: 0x0003
          5. 7.3.1.2.5  RESET_DATA: 0x0005
          6. 7.3.1.2.6  PREV_MACWRITE: 0x0007
          7. 7.3.1.2.7  CHEM ID: 0x0008
          8. 7.3.1.2.8  BOARD_OFFSET: 0x0009
          9. 7.3.1.2.9  CC_OFFSET: 0x000A
          10. 7.3.1.2.10 CC_OFFSET_SAVE: 0x000B
          11. 7.3.1.2.11 DF_VERSION: 0x000C
          12. 7.3.1.2.12 SET_FULLSLEEP: 0x0010
          13. 7.3.1.2.13 STATIC_CHEM_DF_CHKSUM: 0x0017
          14. 7.3.1.2.14 SEALED: 0x0020
          15. 7.3.1.2.15 IT ENABLE: 0x0021
          16. 7.3.1.2.16 CAL_ENABLE: 0x002D
          17. 7.3.1.2.17 RESET: 0x0041
          18. 7.3.1.2.18 EXIT_CAL: 0x0080
          19. 7.3.1.2.19 ENTER_CAL: 0x0081
          20. 7.3.1.2.20 OFFSET_CAL: 0x0082
        3. 7.3.1.3  StateOfCharge(): 0x02
        4. 7.3.1.4  MaxError(): 0x03
        5. 7.3.1.5  RemainingCapacity(): 0x04/0x05
        6. 7.3.1.6  FullChargeCapacity(): 0x06/07
        7. 7.3.1.7  Voltage(): 0x08/0x09
        8. 7.3.1.8  AverageCurrent(): 0x0A/0x0B
        9. 7.3.1.9  Temperature(): 0x0C/0x0D
        10. 7.3.1.10 Flags(): 0x0E/0x0F
        11. 7.3.1.11 FlagsB(): 0x12/0x13
        12. 7.3.1.12 Current(): 0x10/0x11
      2. 7.3.2  Extended Data Commands
        1. 7.3.2.1  AverageTimeToEmpty(): 0x18/0x19
        2. 7.3.2.2  AverageTimeToFull(): 0x1A/0x1B
        3. 7.3.2.3  PassedCharge(): 0x1C/0x1D
        4. 7.3.2.4  DOD0Time(): 0x1E/0x1F
        5. 7.3.2.5  AvailableEnergy(): 0x24/0x25
        6. 7.3.2.6  AveragePower(): 0x26/0x27
        7. 7.3.2.7  SerialNumber(): 0x28/0x29
        8. 7.3.2.8  InternalTemperature(): 0x2A/0x2B
        9. 7.3.2.9  CycleCount(): 0x2C/0x2D
        10. 7.3.2.10 StateOfHealth(): 0x2E/0x2F
        11. 7.3.2.11 ChargeVoltage(): 0x30/0x31
        12. 7.3.2.12 ChargeCurrent(): 0x32/0x33
        13. 7.3.2.13 PackConfiguration(): 0x3A/0x3B
        14. 7.3.2.14 DesignCapacity(): 0x3C/0x3D
        15. 7.3.2.15 DataFlashClass(): 0x3E
        16. 7.3.2.16 DataFlashBlock(): 0x3F
        17. 7.3.2.17 AuthenticateData/BlockData(): 0x40…0x53
        18. 7.3.2.18 AuthenticateChecksum/BlockData(): 0x54
        19. 7.3.2.19 BlockData(): 0x55…0x5F
        20. 7.3.2.20 BlockDataChecksum(): 0x60
        21. 7.3.2.21 BlockDataControl(): 0x61
        22. 7.3.2.22 GridNumber(): 0x62
        23. 7.3.2.23 LearnedStatus(): 0x63
        24. 7.3.2.24 Dod@Eoc(): 0x64/0x65
        25. 7.3.2.25 QStart(): 0x66/0x67
        26. 7.3.2.26 TrueRC(): 0x68/0x69
        27. 7.3.2.27 TrueFCC(): 0x6A/0x6B
        28. 7.3.2.28 StateTime(): 0x6C/0x6D
        29. 7.3.2.29 QmaxPassedQ(): 0x6E/0x6F
        30. 7.3.2.30 DOD0(): 0x70/0x71
        31. 7.3.2.31 QmaxDod0(): 0x72/0x73
        32. 7.3.2.32 QmaxTime(): 0x74/0x75
      3. 7.3.3  Data Flash Interface
        1. 7.3.3.1 Accessing Data Flash
        2. 7.3.3.2 Manufacturer Information Block
        3. 7.3.3.3 Access Modes
        4. 7.3.3.4 Sealing/Unsealing Data Flash Access
      4. 7.3.4  Data Flash Summary
      5. 7.3.5  Fuel Gauging
      6. 7.3.6  Impedance Track Variables
        1. 7.3.6.1  Load Mode
        2. 7.3.6.2  Load Select
        3. 7.3.6.3  Reserve Cap-mAh
        4. 7.3.6.4  Reserve Cap-mWh/cWh
        5. 7.3.6.5  Design Energy Scale
        6. 7.3.6.6  Dsg Current Threshold
        7. 7.3.6.7  Chg Current Threshold
        8. 7.3.6.8  Quit Current, Dsg Relax Time, Chg Relax Time, and Quit Relax Time
        9. 7.3.6.9  Qmax
        10. 7.3.6.10 Update Status
        11. 7.3.6.11 Avg I Last Run
        12. 7.3.6.12 Avg P Last Run
        13. 7.3.6.13 Cell Delta Voltage
        14. 7.3.6.14 Ra Tables
        15. 7.3.6.15 StateOfCharge() Smoothing
        16. 7.3.6.16 Charge Efficiency
        17. 7.3.6.17 Lifetime Data Logging
      7. 7.3.7  Device Configuration
        1. 7.3.7.1 Pack Configuration Register
        2. 7.3.7.2 Pack Configuration B Register
        3. 7.3.7.3 Pack Configuration C Register
      8. 7.3.8  Voltage Measurement and Calibration
        1. 7.3.8.1 1S Example
        2. 7.3.8.2 7S Example
        3. 7.3.8.3 Autocalibration
      9. 7.3.9  Temperature Measurement
      10. 7.3.10 Overtemperature Indication
        1. 7.3.10.1 Overtemperature: Charge
        2. 7.3.10.2 Overtemperature: Discharge
      11. 7.3.11 Charging and Charge Termination Indication
      12. 7.3.12 SCALED Mode
      13. 7.3.13 LED Display
      14. 7.3.14 Alert Signal
      15. 7.3.15 Communications
        1. 7.3.15.1 Authentication
        2. 7.3.15.2 Key Programming
        3. 7.3.15.3 Executing an Authentication Query
        4. 7.3.15.4 HDQ Single-Pin Serial Interface
        5. 7.3.15.5 I2C Interface
        6. 7.3.15.6 Switching Between I2C and HDQ Modes
          1. 7.3.15.6.1 Converting to HDQ Mode
          2. 7.3.15.6.2 Converting to I2C Mode
      16. 7.3.16 Power Control
        1. 7.3.16.1 Reset Functions
        2. 7.3.16.2 Wake-Up Comparator
        3. 7.3.16.3 Flash Updates
    4. 7.4 Device Functional Modes
      1. 7.4.1 NORMAL Mode
      2. 7.4.2 SLEEP Mode
      3. 7.4.3 FULL SLEEP Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Step-by-Step Design Procedure
          1. 8.2.2.1.1 STEP 1: Review and Modify the Data Flash Configuration Data.
          2. 8.2.2.1.2 STEP 2: Review and Modify the Data Flash Configuration Registers.
          3. 8.2.2.1.3 STEP 3: Design and Configure the Voltage Divider.
          4. 8.2.2.1.4 STEP 4: Determine the Sense Resistor Value.
          5. 8.2.2.1.5 STEP 5: Review and Modify the Data Flash Gas Gauging Configuration, Data, and State.
          6. 8.2.2.1.6 STEP 6: Determine and Program the Chemical ID.
          7. 8.2.2.1.7 STEP 7: Calibrate.
          8. 8.2.2.1.8 STEP 8: Run an Optimization Cycle.
      3. 8.2.3 Battery Chemistry Configuration
        1. 8.2.3.1 Battery Chemistry Charge Termination
      4. 8.2.4 Replaceable Battery Systems
      5. 8.2.5 Digital Interface Options
      6. 8.2.6 Display Options
      7. 8.2.7 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Introduction
      2. 10.1.2 Power Supply Decoupling Capacitor
      3. 10.1.3 Capacitors
      4. 10.1.4 Communication Line Protection Components
    2. 10.2 Layout Example
      1. 10.2.1 Ground System
      2. 10.2.2 Kelvin Connections
      3. 10.2.3 Board Offset Considerations
      4. 10.2.4 ESD Spark Gap
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.14 Alert Signal

Based on the selected LED mode, various options are available for the hardware implementation of an Alert signal. Software configuration of the Alert Configuration register determines which alert conditions will assert the ALERT pin.

Table 7-21 ALERT Signal Pins
MODEDESCRIPTIONALERT PINALERT PIN NAMECONFIG REGISTER HEX CODECOMMENT
0No LED1P20
1Single LED1P21
24 LED11P62Filter and FETs are required to eliminate temperature sense pulses. See Section 8.2.
35-LED Expander with I2C Host Comm12P543
310-LED Expander with I2C Host Comm12P593
45-LED Expander with HDQ Host Comm13P444
410-LED Expander with HDQ Host Comm13P494

The port used for the Alert output will depend on the mode setting in LED/Comm Configuration as defined in Table 7-21. The default mode is 0. The ALERT pin will be asserted by driving LOW. However, note that in LED/COM mode 2, pin TS/P6, which has a dual purpose as temperature sense pin, will be driven low except when temperature measurements are made each second. See the reference schematic (Figure 8-4) for filter implementation details if host alert sensing requires a continuous signal.

The ALERT pin will be a logical OR of the selected bits in the new configuration register when asserted in the Flags register. The default value for Alert Configuration register is 0.

Table 7-22 Alert Configuration Register Bit Definitions
Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0
High ByteOTCOTDBAT_HIGHBATLOWCHG_INH XCHGFCCHG
Low ByteOCVTAKENRSVDRSVD CFRSVDRCAEODDSG

Legend: RSVD = Reserved

OTC: Over-Temperature in Charge condition is detected. ALERT is enabled when set.
OTD: Over-Temperature in Discharge condition is detected. ALERT is enabled when set.
BAT_HIGH: Battery High bit that indicates a high battery voltage condition. Refer to the data flash CELL BH parameters for threshold settings. ALERT is enabled when set.
BATLOW: Battery Low bit that indicates a low battery voltage condition. Refer to the data flash parameters for threshold settings. ALERT is enabled when set.
CHG_INH: Charge Inhibit: unable to begin charging. Refer to the data flash [Charge Inhibit Temp Low, Charge Inhibit Temp High] parameters. ALERT is enabled when set.
XCHG: Charging disallowed ALERT is enabled when set.
FC: Full charge is detected. FC is set when charge termination is reached and FC Set% = –1 (see Section 7.3.11 for details) or StateOfCharge() is larger than FC Set% and FC Set% is not –1. ALERT is enabled when set.
CHG: (Fast) charging allowed. ALERT is enabled when set.
OCVTAKEN: Cleared on entry to RELAX mode and set to 1 when OCV measurement is performed in RELAX mode. ALERT is enabled when set.
CF: Condition Flag set. ALERT is enabled when set.
RCA: Remaining Capacity Alarm reached. ALERT is enabled when set.
EOD: End-of-Discharge Threshold reached. ALERT is enabled when set.
DSG: Discharging detected. ALERT is enabled when set.