JAJSQQ5A december   2022  – june 2023 CC1354R10

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Functional Block Diagram
  6. 5 Revision History
  7. 6 Device Comparison
  8. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram – RGZ Package (Top View)
    2. 7.2 Signal Descriptions – RGZ Package
    3. 7.3 Connections for Unused Pins and Modules – RGZ Package
    4. 7.4 Pin Diagram – RSK Package (Top View)
    5. 7.5 Signal Descriptions – RSK Package
    6. 7.6 Connection of Unused Pins and Module – RSK Package
  9. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Power Supply and Modules
    5. 8.5  Power Consumption - Power Modes
    6. 8.6  Power Consumption - Radio Modes
    7. 8.7  Nonvolatile (Flash) Memory Characteristics
    8. 8.8  Thermal Resistance Characteristics
    9. 8.9  RF Frequency Bands
    10. 8.10 861 MHz to 1054 MHz - Receive (RX)
    11. 8.11 861 MHz to 1054 MHz - Transmit (TX) 
    12. 8.12 861 MHz to 1054 MHz - PLL Phase Noise Wideband Mode
    13. 8.13 861 MHz to 1054 MHz - PLL Phase Noise Narrowband Mode
    14. 8.14 Bluetooth Low Energy - Receive (RX)
    15. 8.15 Bluetooth Low Energy - Transmit (TX)
    16. 8.16 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
    17. 8.17 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - TX
    18. 8.18 Timing and Switching Characteristics
      1. 8.18.1 Reset Timing
      2. 8.18.2 Wakeup Timing
      3. 8.18.3 Clock Specifications
        1. 8.18.3.1 48 MHz Clock Input (TCXO)
        2. 8.18.3.2 48 MHz Crystal Oscillator (XOSC_HF)
        3. 8.18.3.3 48 MHz RC Oscillator (RCOSC_HF)
        4. 8.18.3.4 2 MHz RC Oscillator (RCOSC_MF)
        5. 8.18.3.5 32.768 kHz Crystal Oscillator (XOSC_LF)
        6. 8.18.3.6 32 kHz RC Oscillator (RCOSC_LF)
      4. 8.18.4 Serial Peripheral Interface (SPI) Characteristics
        1. 8.18.4.1 SPI Characteristics
        2. 8.18.4.2 SPI Master Mode
        3. 8.18.4.3 SPI Master Mode Timing Diagrams
        4. 8.18.4.4 SPI Slave Mode
        5. 8.18.4.5 SPI Slave Mode Timing Diagrams
      5. 8.18.5 UART
        1. 8.18.5.1 UART Characteristics
    19. 8.19 Peripheral Characteristics
      1. 8.19.1 ADC
        1. 8.19.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 8.19.2 DAC
        1. 8.19.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 8.19.3 Temperature and Battery Monitor
        1. 8.19.3.1 Temperature Sensor
        2. 8.19.3.2 Battery Monitor
      4. 8.19.4 Comparators
        1. 8.19.4.1 Low-Power Clocked Comparator
        2. 8.19.4.2 Continuous Time Comparator
      5. 8.19.5 Current Source
        1. 8.19.5.1 Programmable Current Source
      6. 8.19.6 GPIO
        1. 8.19.6.1 GPIO DC Characteristics
    20. 8.20 Typical Characteristics
      1. 8.20.1 MCU Current
      2. 8.20.2 RX Current
      3. 8.20.3 TX Current
      4. 8.20.4 RX Performance
      5. 8.20.5 TX Performance
      6. 8.20.6 ADC Performance
  10. 9 Detailed Description
    1. 9.1  Overview
    2. 9.2  System CPU
    3. 9.3  Radio (RF Core)
      1. 9.3.1 Proprietary Radio Formats
      2. 9.3.2 Bluetooth 5.3 Low Energy
      3. 9.3.3 802.15.4 Thread, Zigbee, and 6LoWPAN
    4. 9.4  Memory
    5. 9.5  Sensor Controller
    6. 9.6  Cryptography
    7. 9.7  Timers
    8. 9.8  Serial Peripherals and I/O
    9. 9.9  Battery and Temperature Monitor
    10. 9.10 µDMA
    11. 9.11 Debug
    12. 9.12 Power Management
    13. 9.13 Clock Systems
    14. 9.14 Network Processor
  11. 10Application, Implementation, and Layout
    1. 10.1 Reference Designs
    2. 10.2 Junction Temperature Calculation
  12. 11Device and Documentation Support
    1. 11.1 Tools and Software
      1. 11.1.1 SimpleLink™ Microcontroller Platform
    2. 11.2 Documentation Support
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.10 861 MHz to 1054 MHz - Receive (RX)

When measured on the LP-EM-CC1354P10-1 reference design with Tc = 25 °C, VDDS = 3.0 V with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX path. All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Digital channel filter programmable receive bandwidth 4 4000 kHz
Data rate step size 1.5 bps
Spurious emissions 25 MHz to 1 GHz 868 MHz
Conducted emissions measured according to ETSI EN 300 220		 < -57 dBm
Spurious emissions 1 GHz to 13 GHz < -47 dBm
Wi-SUN, 50 kbps, ±12.5 kHz deviation, 2-GFSK, 78 kHz RX BW, #1a
Sensitivity MRFSK, 866.6 MHz, 10% PER, 250 byte payload -106 dBm
Saturation limit 10% PER, 250 byte payload, 866.6 MHz 10 dBm
Selectivity, +100 kHz 10% PER, 250 byte payload, 866.6 MHz. Wanted signal 3 dB above sensitivity level. 33 dB
Selectivity, -100 kHz 31 dB
Selectivity, +200 kHz 38 dB
Selectivity, -200 kHz 37 dB
RSSI dynamic range Starting from the sensitivity limit  93 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 50 kbps, ±25 kHz deviation, 2-GFSK, 100 kHz RX BW, #1b
Sensitivity MRFSK, 918.2 MHz, 10% PER, 250 byte payload -106 dBm
Saturation limit 10% PER, 250 byte payload, 918.2 MHz 10 dBm
Selectivity, +200 kHz 10% PER, 250 byte payload, 918.2 MHz. Wanted signal 3 dB above sensitivity level. 37 dB
Selectivity, -200 kHz 35 dB
Selectivity, +400 kHz 42 dB
Selectivity, -400 kHz 41 dB
RSSI dynamic range Starting from the sensitivity limit  95 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 100 kbps, ±25 kHz deviation, 2-GFSK, 135 kHz RX BW, #2a
Sensitivity MRFSK, 866.6 MHz, 10% PER, 250 byte payload -103 dBm
Saturation limit 10% PER, 250 byte payload, 866.6 MHz 10 dBm
Selectivity, +200 kHz 10% PER, 250 byte payload, 866.6 MHz. Wanted signal 3 dB above sensitivity level. 40 dB
Selectivity, -200 kHz 38 dB
Selectivity, +400 kHz 46 dB
Selectivity, -400 kHz 44 dB
RSSI dynamic range Starting from the sensitivity limit  95 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 100 kbps, ±50 kHz deviation, 2-GFSK, 208 kHz RX BW, #2b
Sensitivity MRFSK, 920.9 MHz, 10% PER, 250 byte payload -102 dBm
Saturation limit 10% PER, 250 byte payload, 920.9 MHz 10 dBm
Selectivity, +400 kHz 10% PER, 250 byte payload, 920.9 MHz. Wanted signal 3 dB above sensitivity level, modulated blocker. 42 dB
Selectivity, -400 kHz 39 dB
Selectivity, +800 kHz 52 dB
Selectivity, -800 kHz 46 dB
RSSI dynamic range Starting from the sensitivity limit  91 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 150 kbps, ±37.5 kHz deviation, 2-GFSK, 273 kHz RX BW, #3
Sensitivity MRFSK, 918.4 MHz, 10% PER, 250 byte payload -99 dBm
Saturation limit 10% PER, 250 byte payload, 918.4 MHz 10 dBm
Selectivity, +400 kHz 10% PER, 250 byte payload, 918.4 MHz. Wanted signal 3 dB above sensitivity level. 41 dB
Selectivity, -400 kHz 39 dB
Selectivity, +800 kHz 50 dB
Selectivity, -800 kHz 46 dB
RSSI dynamic range Starting from the sensitivity limit  86 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 200 kbps, ±50 kHz deviation, 2-GFSK, 335 kHz RX BW, #4a
Sensitivity MRFSK, 918.4 MHz, 10% PER, 250 byte payload -99 dBm
Saturation limit 10% PER, 250 byte payload, 918.4 MHz 10 dBm
Selectivity, +400 kHz 10% PER, 250 byte payload, 918.4 MHz. Wanted signal 3 dB above sensitivity level. 42 dB
Selectivity, -400 kHz 40 dB
Selectivity, +800 kHz 51 dB
Selectivity, -800 kHz 47 dB
RSSI dynamic range Starting from the sensitivity limit  91 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 200 kbps, ±100 kHz deviation, 2-GFSK, 416 kHz RX BW, #4b
Sensitivity MRFSK, 920.8 MHz, 10% PER, 250 byte payload -98 dBm
Saturation limit 10% PER, 250 byte payload, 920.8 MHz 10 dBm
Selectivity, +600 kHz 10% PER, 250 byte payload, 920.8 MHz. Wanted signal 3 dB above sensitivity level, modulated blocker. 46 dB
Selectivity, -600 kHz 43 dB
Selectivity, +1200 kHz 54 dB
Selectivity, -1200 kHz 51 dB
RSSI dynamic range Starting from the sensitivity limit  86 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wi-SUN, 300 kbps, ±75 kHz deviation, 2-GFSK, 496 kHz RX BW, #5
Sensitivity MRFSK, 917.6 MHz, 10% PER, 250 byte payload -97 dBm
Saturation limit 10% PER, 250 byte payload, 917.6 MHz 10 dBm
Selectivity, +600 kHz 10% PER, 250 byte payload, 917.6 MHz. Wanted signal 3 dB above sensitivity level. 42 dB
Selectivity, -600 kHz 37 dB
Selectivity, +1200 kHz 51 dB
Selectivity, -1200 kHz 40 dB
RSSI dynamic range Starting from the sensitivity limit  86 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
802.15.4-2020, 10 kbps, 2-FSK, 26 kHz RX BW, Mode #1a
Sensitivity FSK, 915.0 MHz, 20 byte PSDU < 10% PER -113 dBm
Sensitivity FSK, 868.3 MHz, 20 byte PSDU < 10% PER -113 dBm
Saturation limit PSDU length 20 octets; PER < 10%, 868.3 MHz 10 dBm
Selectivity, +50 kHz PSDU length 20 octets; PER < 10%, 868.3 MHz 36 dB
Selectivity, -50 kHz 36 dB
Selectivity, +100 kHz 40 dB
Selectivity, -100 kHz 39 dB
Selectivity, +200 kHz 44 dB
Selectivity, -200 kHz 37 dB
Blocking, +1 MHz 60 dB
Blocking, -1 MHz 59 dB
Blocking, +2 MHz 64 dB
Blocking, -2 MHz 64 dB
Blocking, +5 MHz 75 dB
Blocking, -5 MHz 74 dB
Blocking, +10 MHz 79 dB
Blocking, -10 MHz 79 dB
Selectivity, +50 kHz PSDU length 20 octets; PER < 10%, 868.3 MHz. Wanted signal 3 dB above sensitivity level. 35 dB
Selectivity, -50 kHz 35 dB
Selectivity, +100 kHz 39 dB
Selectivity, -100 kHz 38 dB
Selectivity, +200 kHz 44 dB
Selectivity, -200 kHz 44 dB
Blocking, +1 MHz 58 dB
Blocking, -1 MHz 58 dB
Blocking, +2 MHz 62 dB
Blocking, -2 MHz 63 dB
Blocking, +5 MHz 74 dB
Blocking, -5 MHz 74 dB
Blocking, +10 MHz 73 dB
Blocking, -10 MHz 78 dB
Blocking + 5% Fc. (45.75 MHz) 10% PER, 20 byte payload, 866.6 MHz 802.15.4g mandatory mode, wanted signal -94 dBm. 3 dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97 dBm). Limit is Cat 1.5 requirement. -15 dBm
Blocking - 5% Fc. (-45.75 MHz) -15 dBm
Image rejection (image compensation enabled) 39 dB
Image rejection (image compensation enabled) PSDU length 20 octets; PER < 10%, 868.3 MHz 39 dB
Image rejection (image compensation enabled) -40 to 125℃, 10% PER, 250 byte payload, 866.6 MHz 39 dB
RSSI dynamic range Starting from the sensitivity limit  100 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Frequency error tolerance (ppm) 10% PER, 20 byte payload, measured at 10 dB above sensitivity level. Negative offset -12 ppm
Frequency error tolerance (ppm) 10% PER, 20 byte payload, measured at 10 dB above sensitivity level. Positive offset 12 ppm
Symbol rate error tolerance (ppm) 10% PER, 20 byte payload, measured at 10 dB above sensitivity level.
Negative offset		 -1000 ppm
Symbol rate error tolerance (ppm) 1% BER, measured at 10 dB above sensitivity level
Positive offset		 1000 ppm
802.15.4-2020, 20 kbps, 2-FSK, 52 kHz RX BW, Mode #1b
Sensitivity FSK, 20 kbps, ±10 kHz deviation, 2-GFSK, 915.0 MHz, 52 kHz RX BW, 20 byte PSDU < 10% PER -110 dBm
Sensitivity FSK, 20 kbps, ±10 kHz deviation, 2-GFSK, 868.3 MHz, 52 kHz RX BW, 20 byte PSDU < 10% PER -110 dBm
Saturation limit 20 byte PSDU < 10% PER, 868.3 MHz 10 dBm
Selectivity, +100 kHz 20 byte PSDU < 10% PER, 868.3 MHz 38 dB
Selectivity, -100 kHz 36 dB
Selectivity, +200 kHz 44 dB
Selectivity, -200 kHz 42 dB
Selectivity, +400 kHz 49 dB
Selectivity, -400 kHz 44 dB
Blocking, +1 MHz 58 dB
Blocking, -1 MHz 54 dB
Blocking, -2 MHz 61 dB
Blocking, +2 MHz 61 dB
Blocking, -5 MHz 70 dB
Blocking, +5 MHz 70 dB
Blocking, -10 MHz 75 dB
Blocking, +10 MHz 76 dB
Selectivity, +100 kHz 20 byte PSDU < 10% PER, 868.3 MHz. Wanted signal 3 dB above sensitivity level. 36 dB
Selectivity, -100 kHz 34 dB
Selectivity, +200 kHz 42 dB
Selectivity, -200 kHz 41 dB
Selectivity, +400 kHz 47 dB
Selectivity, -400 kHz 46 dB
Blocking, +1 MHz 56 dB
Blocking, -1 MHz 55 dB
Blocking, +2 MHz 61 dB
Blocking, -2 MHz 61 dB
Blocking, +5 MHz 71 dB
Blocking, -5 MHz 70 dB
Blocking, +10 MHz 75 dB
Blocking, -10 MHz 75 dB
Blocking + 5% Fc. (45.75 MHz) 20 byte PSDU < 10% PER, 866.6 MHz,  wanted signal -94 dBm. 3 dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97 dBm). Limit is Cat 1.5 requirement. -13 dBm
Blocking - 5% Fc. (-45.75 MHz) -13 dBm
Image rejection (image compensation enabled) 20 byte PSDU < 10% PER, 866.6 MHz. Wanted signal 3 dB above sensitivity limit. 39 dB
Image rejection (image compensation enabled) 20 byte PSDU < 10% PER, 866.6 MHz(1) 39 dB
Image rejection (image compensation enabled) -40 to 125℃, 10% PER, 250 byte payload, 866.6 MHz 39 dB
RSSI dynamic range Starting from the sensitivity limit  100 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Frequency error tolerance (ppm) 20 byte PSDU < 10% PER, measured at 10 dB above sensitivity level. Negative offset -24 ppm
Frequency error tolerance (ppm) 20 byte PSDU < 10% PER, measured at 10 dB above sensitivity level. Positive offset 24 ppm
Symbol rate error tolerance (ppm) 20 byte PSDU < 10% PER, measured at 10 dB above sensitivity level.
Negative offset		 -1000 ppm
Symbol rate error tolerance (ppm) 20 byte PSDU < 10% PER, measured at 10 dB above sensitivity level.
Negative offset		 1000 ppm
802.15.4, 200 kbps, ±50 kHz deviation, 2-GFSK, 311 kHz RX BW
Sensitivity BER = 10–2, 868 MHz –103 dBm
Sensitivity BER = 10–2, 915 MHz –103 dBm
Selectivity, +400 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 45 dB
Selectivity, -400 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 45 dB
Selectivity, +800 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 52 dB
Selectivity, -800 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 47 dB
Blocking, +2 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 59 dB
Blocking, -2 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 56 dB
Blocking, +10 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 71 dB
Blocking, -10 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 70 dB
802.15.4, 500 kbps, ±190 kHz deviation, 2-GFSK, 622 kHz RX BW
Sensitivity 500 kbps 915 MHz, 1% PER, 127 byte payload -95 dBm
Selectivity, ±1 MHz 915 MHz, 1% PER, 127 byte payload. Wanted signal at -88 dBm 34 dB
Selectivity, ±2 MHz 915 MHz, 1% PER, 127 byte payload. Wanted signal at -88 dBm 46 dB
Co-channel rejection 915 MHz, 1% PER, 127 byte payload. Wanted signal at -71 dBm -8 dB
SimpleLink™ Long Range  2.5/5 kbps (20 ksps), ±5 kHz Deviation, 2-GFSK, 34 kHz RX Bandwidth, FEC = 1:2, DSSS = 1:4/1:2
Sensitivity 2.5 kbps, BER = 10–2, 868 MHz -121 dBm
Sensitivity 2.5 kbps, BER = 10–2, 915 MHz -121 dBm
Sensitivity 5 kbps, BER = 10–2, 868 MHz -119 dBm
Sensitivity 5 kbps, BER = 10–2, 915 MHz -119 dBm
Saturation limit 2.5 kbps, BER = 10–2, 868 MHz 10 dBm
Selectivity, +100 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 49 dB
Selectivity, -100 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 49 dB
Selectivity, +200 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 52 dB
Selectivity, -200 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 48 dB
Selectivity, +300 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 54 dB
Selectivity, -300 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 48 dB
Blocking, +1 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 65 dB
Blocking, -1 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 60 dB
Blocking, +2 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 70 dB
Blocking, -2 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 68 dB
Blocking, +5 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 78 dB
Blocking, -5 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 77 dB
Blocking, +10 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 87 dB
Blocking, -10 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 92 dB
Image rejection (image compensation enabled) 2.5 kbps, BER = 10–2, 868 MHz(1) 47 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Frequency error tolerance (ppm) 2.5 kbps, 20 kbaud, DSSS=4, ½ K=7 FEC. measured at -110 dBm.  -24/26 ppm
Symbolrate error tolerance (ppm) 2.5 kbps, 20 kbaud, DSSS=4, ½ K=7 FEC. measured at -110 dBm. Refered to 20 kbaud chip rate. -90/70 ppm
Narrowband, 9.6 kbps ±2.4 kHz deviation, 2-GFSK, 868 MHz, 17.1 kHz RX BW
Sensitivity 1% BER -117 dBm
Adjacent Channel Rejection 1% BER. Wanted signal 3 dB above usable sensitivity limit (usable sensitivity -104.6 dBm). Interferer ±20 kHz 42 dB
Alternate Channel Rejection 1% BER. Wanted signal 3 dB above usable sensitivity limit (usable sensitivity -104.6 dBm). Interferer ±40 kHz 42 dB
Blocking, ±1 MHz 1% BER. Wanted signal 3 dB above usable sensitivity limit (usable sensitivity -104.6 dBm). 66 dB
Blocking, ±2 MHz 1% BER. Wanted signal 3 dB above usable sensitivity limit (usable sensitivity -104.6 dBm). 71 dB
Blocking, ±10 MHz 1% BER. Wanted signal 3 dB above usable sensitivity limit (usable sensitivity -104.6 dBm). 85 dB
802.15.4, 50 kbps, ±25 kHz Deviation, 2-GFSK, 100 kHz RX BW (Legacy)
Sensitivity BER = 10–2, 868 MHz –110 dBm
Sensitivity BER = 10–2, 915 MHz –110 dBm
Saturation limit BER = 10–2, 868 MHz 10 dBm
Selectivity, +200 kHz BER = 10–2, 868 MHz(1) 44 dB
Selectivity, -200 kHz 44 dB
Selectivity, +400 kHz 54 dB
Selectivity, -400 kHz 44 dB
Blocking, +1 MHz 57 dB
Blocking, -1 MHz 57 dB
Blocking, +2 MHz 61 dB
Blocking, -2 MHz 61 dB
Blocking, +5 MHz 67 dB
Blocking, -5 MHz 67 dB
Blocking, +10 MHz 76 dB
Blocking, -10 MHz 76 dB
Selectivity, +200 kHz BER = 10–2, 868 MHz. Wanted signal 3 dB above sensitivity limit. 45 dB
Selectivity, -200 kHz 45 dB
Selectivity, +400 kHz 51 dB
Selectivity, -400 kHz 45 dB
Blocking, +1 MHz 61 dB
Blocking, -1 MHz 61 dB
Blocking, +2 MHz 63 dB
Blocking, -2 MHz 63 dB
Blocking, +5 MHz 67 dB
Blocking, -5 MHz 67 dB
Blocking, +10 MHz 73 dB
Blocking, -10 MHz 73 dB
Blocking + 5% Fc. (43.42 MHz) BER = 10–2, 868 MHz
802.15.4g mandatory mode, wanted signal -94 dBm. 3 dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97 dBm). Limit is Cat 1.5 requirement. 		-15 dBm
Blocking - 5% Fc. (-43.42 MHz) -15 dBm
Image rejection (image compensation enabled) BER = 10–2, 868 MHz. Wanted signal 3 dB above sensitivity limit. 39 dB
Image rejection (image compensation enabled) BER = 10–2, 868 MHz(1) 39 dB
Image rejection (image compensation enabled) -40 to 125℃.  BER = 10–2, 868 MHz 41 dB
RSSI dynamic range Starting from the sensitivity limit  95 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Frequency error tolerance (ppm) 1% BER, measured at -100 dBm (10 dB above sensitivity level). Negative offset -30 ppm
Frequency error tolerance (ppm) 1% BER, measured at -100 dBm (10 dB above sensitivity level). Positive offset 25 ppm
Symbol rate error tolerance (ppm) 1% BER, measured at-100 dBm (10 dB above sensitivity level).
Negative offset 		-2000 ppm
Symbol rate error tolerance (ppm) 1% BER, measured at-100 dBm (10 dB above sensitivity level)
Positive offset 		2000 ppm
802.15.4, 100 kbps, ±25 kHz deviation, 2-GFSK, 137 kHz RX BW
Sensitivity 100 kbps 868 MHz, 1% PER, 127 byte payload -103 dBm
Selectivity, ±200 kHz 868 MHz, 1% PER, 127 byte payload. Wanted signal at -96 dBm 38 dB
Selectivity, ±400 kHz 44 dB
Co-channel rejection 868 MHz, 1% PER, 127 byte payload. Wanted signal at -79 dBm -9 dB
Generic OOK (16.384 kbps, OOK w / Manchester encoding, 100 kHz RX BW)
Sensitivity OOK, 915.0 MHz, 1% BER -114 dBm
Sensitivity OOK, 868.8 MHz, 1% BER -113 dBm
Saturation limit 868.3 MHz 0 dBm
Selectivity, +200 kHz 868.3 MHz(1) 52 dB
Selectivity, -200 kHz 48 dB
Selectivity, +400 kHz 68 dB
Selectivity, -400 kHz 64 dB
Blocking, +1 MHz 64 dB
Blocking, -1 MHz 59 dB
Blocking, +2 MHz 64 dB
Blocking, -2 MHz 59 dB
Blocking, +5 MHz 72 dB
Blocking, -5 MHz 73 dB
Blocking, +10 MHz 64 dB
Blocking, -10 MHz 58 dB
Selectivity, +200 kHz 868.3 MHz. Wanted signal 3 dB above sensitivity level. 52 dB
Selectivity, -200 kHz 47 dB
Selectivity, +400 kHz 42 dB
Selectivity, -400 kHz 42 dB
Blocking, +1 MHz 68 dB
Blocking, -1 MHz 64 dB
Blocking, +2 MHz 68 dB
Blocking, -2 MHz 64 dB
Blocking, +5 MHz 74 dB
Blocking, -5 MHz 73 dB
Blocking, +10 MHz 68 dB
Blocking, -10 MHz 64 dB
RSSI dynamic range Starting from the sensitivity limit  95 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Frequency error tolerance (ppm) Measured at  10 dB above sensitivity level. Negative offset -40 ppm
Frequency error tolerance (ppm) Measured at 10 dB above sensitivity level. Positive offset 40 ppm
Symbol rate error tolerance (ppm) Measured at 10 dB above sensitivity level.
Negative offset		 -2000 ppm
Symbol rate error tolerance (ppm) Measured at 10 dB above sensitivity level
Positive offset		 2000 ppm
(1) Wanted signal 3 dB above usable sensitivity limit according to ETSI EN 300 220 v. 3.1.1.