JAJSF34B November   2017  – May 2022 DLPC120-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1. 5.1 LED Driver Interface
    2. 5.2 DMD Temperature Interface
    3.     General Purpose I/O
    4. 5.3 Main Video and Data Control Interface
    5. 5.4 DMD Interface
    6. 5.5 Memory Interface
    7.     Board Level Test and Debug
    8.     Manufacturing Test Support
    9.     Test Point Interface
    10.     Power and Ground
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Electrical Characteristics for I/O
    7. 6.7  Power Supply and Reset Timing Requirements
    8. 6.8  Reference Clock PLL Timing Requirements
    9. 6.9  Parallel Interface General Timing Requirements
    10. 6.10 Parallel Interface Frame Timing Requirements
    11. 6.11 Flash Memory Interface Timing Requirements
    12. 6.12 DMD Interface Timing Requirements
    13. 6.13 JTAG Interface Timing Requirements
    14. 6.14 I2C Interface Timing Requirements
  7. 7 Parameter Measurement Information
    1. 7.1 Parallel Interface Input Source Timing
    2. 7.2 Design for Test Functions
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Serial Flash Interface
      2. 8.3.2 Serial Flash Programming
      3. 8.3.3 DDR2 Memory Interface
      4. 8.3.4 JTAG and DMD Interface Test
      5. 8.3.5 Temperature Monitor Function
      6. 8.3.6 Host Command Interface
    4. 8.4 Device Functional Modes
      1. 8.4.1 External Video Mode
      2. 8.4.2 Splash Screen Mode
      3. 8.4.3 Test Pattern Mode
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
  10. 10Power Supply Recommendations
    1. 10.1 Power Supply Filtering
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 PCB layout guidelines for internal ASIC PLL power
      2. 11.1.2 DLPC120-Q1 Reference Clock
        1. 11.1.2.1 Recommended Crystal Oscillator Configuration
      3. 11.1.3 General PCB Recommendations
      4. 11.1.4 PCB Routing Guidelines
      5. 11.1.5 Number of Layer Changes
      6. 11.1.6 Terminations
      7. 11.1.7 General Handling Guidelines for Unused CMOS-Type Pins
  12. 12Device and Documentation Support
    1. 12.1 Third-Party Products Disclaimer
    2. 12.2 Device Support
      1. 12.2.1 Device Nomenclature
        1. 12.2.1.1 Device Markings
    3. 12.3 Documentation Support
      1. 12.3.1 Related Documentation
    4. 12.4 Receiving Notification of Documentation Updates
    5. 12.5 サポート・リソース
    6. 12.6 Trademarks
    7. 12.7 Electrostatic Discharge Caution
    8. 12.8 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • ZXS|216
サーマルパッド・メカニカル・データ
発注情報

6.14 I2C Interface Timing Requirements

MINMAXUNIT
ƒsclClock frequency20400kHz
tschClock duration high0.6μs
tsclClock duration low1.3μs
tspSpike time0400ns
tsdsSetup time100(3)ns
tsdhHold time0(1)0.9(2)μs
ticrInput rise time20 + 0.1 x Cb(4)300ns
tocfOutput fall time1 + 0.1 x Cb(4)300ns
tbufBus free time between stop and start conditions1.3μs
tstsStart or repeated start condition setup0.6μs
tsthStart or repeated start condition hold0.6μs
tsphStop condition hold0.6μs
(1) A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL.
(2) The maximum tHD_DAT has only to be met if the device does not stretch the LOW period (tLOW) of the SCL signal.
(3) A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement tSU_DAT 250 ns must then be met. This is automatically the case since the device does not stretch the LOW period of the SCL signal.
(4) Cb = total capacitance of one bus line in pF.