JAJSLD1C May   2021  – November 2022 DLPC6540

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Electrical Characteristics
    6. 6.6  Pin Electrical Characteristics
    7. 6.7  DMD HSSI Electrical Characteristics
    8. 6.8  DMD Low-Speed LVDS Electrical Characteristics
    9. 6.9  V-by-One Interface Electrical Characteristics
    10. 6.10 USB Electrical Characteristics
    11. 6.11 System Oscillator Timing Requirements
    12. 6.12 Power Supply and Reset Timing Requirements
    13. 6.13 DMD HSSI Timing Requirements
    14. 6.14 DMD Low-Speed LVDS Timing Requirements
    15. 6.15 V-by-One Interface General Timing Requirements
    16. 6.16 Source Frame Timing Requirements
    17. 6.17 Synchronous Serial Port Interface Timing Requirements
    18. 6.18 Master and Slave I2C Interface Timing Requirements
    19. 6.19 Programmable Output Clock Timing Requirements
    20. 6.20 JTAG Boundary Scan Interface Timing Requirements (Debug Only)
    21. 6.21 JTAG ARM Multi-Ice Interface Timing Requirements (Debug Only)
    22. 6.22 Multi-Trace ETM Interface Timing Requirements
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Input Sources
      2. 7.3.2 Processing Delays
      3. 7.3.3 V-by-One Interface
      4. 7.3.4 DMD (HSSI) Interface
      5. 7.3.5 Program Memory Flash Interface
      6. 7.3.6 GPIO Supported Functionality
      7. 7.3.7 Debug Support
    4. 7.4 Device Operational Modes
      1. 7.4.1 Standby Mode
      2. 7.4.2 Active Mode
        1. 7.4.2.1 Normal Configuration
  8. 8 Power Supply Recommendations
    1. 8.1 Power Supply Management
    2. 8.2 Hot Plug Usage
    3. 8.3 Power Supplies for Unused Input Source Interfaces
    4. 8.4 Power Supplies
      1. 8.4.1 1.15-V Power Supplies
      2. 8.4.2 1.21V Power Supply
      3. 8.4.3 1.8-V Power Supplies
      4. 8.4.4 3.3-V Power Supplies
  9. 9 Layout
    1. 9.1 Layout Guidelines
      1. 9.1.1 General Layout Guidelines
      2. 9.1.2 Power Supply Layout Guidelines
      3. 9.1.3 Layout Guidelines for Internal Controller PLL Power
      4. 9.1.4 Layout Guideline for DLPC6540 Reference Clock
        1. 9.1.4.1 Recommended Crystal Oscillator Configuration
      5. 9.1.5 V-by-One Interface Layout Considerations
      6. 9.1.6 USB Interface Layout Considerations
      7. 9.1.7 DMD Interface Layout Considerations
      8. 9.1.8 General Handling Guidelines for Unused CMOS-Type Pins
      9. 9.1.9 Maximum Pin-to-Pin, PCB Interconnects Etch Lengths
    2. 9.2 Thermal Considerations
  10. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Device Nomenclature
        1. 10.1.2.1 Device Markings
        2. 10.1.2.2 Package Data
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
      1. 10.6.1 Video Timing Parameter Definitions
  11. 11Mechanical, Packaging, and Orderable Information
    1.     79

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.7 Debug Support

The DLPC6540 contains a test point output port, TSTPT_(7:0), which provides the Host with the ability to provide for Controller debug support. For initial debug operation, the four signals (TSTPT(3:0)) are sampled as inputs approximately 1.5 µs after PWRGOOD goes high (or after a system reset). Once their input state has been sampled and captured, this information is used to setup the initial test mode output state of the TSTPT_(7:0) bus. Table 7-19 defines the test mode selection for a few programmable output states for TSTPT_(7:0). Use the default state of 0000 (defined by the required external pulldown resistors) for normal operation (that is, no debug required).

To allow TI to make use of this debug capability, providing for the option of a jumper to an external pullup is recommended for TSTPT(3:0), as well as providing access to allow observation of the TSTPT bus outputs.

Table 7-19 Examples of Test Mode Selection Outputs Defined by TSTPT(3:0)(1)
TSTPT_(7:0) OUTPUTTSTPT(3:0) CAPTURED VALUES
0000 (DEFAULT)
(NO SWITCHING ACTIVITY)		0101
CLOCK DEBUG		1000
SYSTEM CALIBRATION
TSTPT(0)0HIGHVertical Sync
TSTPT(1)0166.25 MHzDelayed CW Index
TSTPT(2)083.13 MHzSequence Index
TSTPT(3)041.56 MHzCW Spoke Test Point
TSTPT(4)010.39 MHzCW Revolution Test Point
TSTPT(5)025.16 MHzReset Sequence Aux Bit 0
TSTPT(6)0133.00 MHzReset Sequence Aux Bit 1
TSTPT(7)0HIGHReset Sequence Aux Bit 2
(1) These are only the default output selections. Software can reprogram the selection at any time.