JAJSLD1C May   2021  – November 2022 DLPC6540

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Electrical Characteristics
    6. 6.6  Pin Electrical Characteristics
    7. 6.7  DMD HSSI Electrical Characteristics
    8. 6.8  DMD Low-Speed LVDS Electrical Characteristics
    9. 6.9  V-by-One Interface Electrical Characteristics
    10. 6.10 USB Electrical Characteristics
    11. 6.11 System Oscillator Timing Requirements
    12. 6.12 Power Supply and Reset Timing Requirements
    13. 6.13 DMD HSSI Timing Requirements
    14. 6.14 DMD Low-Speed LVDS Timing Requirements
    15. 6.15 V-by-One Interface General Timing Requirements
    16. 6.16 Source Frame Timing Requirements
    17. 6.17 Synchronous Serial Port Interface Timing Requirements
    18. 6.18 Master and Slave I2C Interface Timing Requirements
    19. 6.19 Programmable Output Clock Timing Requirements
    20. 6.20 JTAG Boundary Scan Interface Timing Requirements (Debug Only)
    21. 6.21 JTAG ARM Multi-Ice Interface Timing Requirements (Debug Only)
    22. 6.22 Multi-Trace ETM Interface Timing Requirements
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Input Sources
      2. 7.3.2 Processing Delays
      3. 7.3.3 V-by-One Interface
      4. 7.3.4 DMD (HSSI) Interface
      5. 7.3.5 Program Memory Flash Interface
      6. 7.3.6 GPIO Supported Functionality
      7. 7.3.7 Debug Support
    4. 7.4 Device Operational Modes
      1. 7.4.1 Standby Mode
      2. 7.4.2 Active Mode
        1. 7.4.2.1 Normal Configuration
  8. 8 Power Supply Recommendations
    1. 8.1 Power Supply Management
    2. 8.2 Hot Plug Usage
    3. 8.3 Power Supplies for Unused Input Source Interfaces
    4. 8.4 Power Supplies
      1. 8.4.1 1.15-V Power Supplies
      2. 8.4.2 1.21V Power Supply
      3. 8.4.3 1.8-V Power Supplies
      4. 8.4.4 3.3-V Power Supplies
  9. 9 Layout
    1. 9.1 Layout Guidelines
      1. 9.1.1 General Layout Guidelines
      2. 9.1.2 Power Supply Layout Guidelines
      3. 9.1.3 Layout Guidelines for Internal Controller PLL Power
      4. 9.1.4 Layout Guideline for DLPC6540 Reference Clock
        1. 9.1.4.1 Recommended Crystal Oscillator Configuration
      5. 9.1.5 V-by-One Interface Layout Considerations
      6. 9.1.6 USB Interface Layout Considerations
      7. 9.1.7 DMD Interface Layout Considerations
      8. 9.1.8 General Handling Guidelines for Unused CMOS-Type Pins
      9. 9.1.9 Maximum Pin-to-Pin, PCB Interconnects Etch Lengths
    2. 9.2 Thermal Considerations
  10. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Device Nomenclature
        1. 10.1.2.1 Device Markings
        2. 10.1.2.2 Package Data
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
      1. 10.6.1 Video Timing Parameter Definitions
  11. 11Mechanical, Packaging, and Orderable Information
    1.     79

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.1.1 General Layout Guidelines

In order to meet the thermal loads associated with the DLPC6540, TI recommends the following enhanced PCB design parameters.

  • A minimum of 4 power and ground planes
    • Power layers: 1-oz. copper; Ground layers: 2-oz. copper
      • Copper coverage: 90%
    • Top and bottom signal layers: minimum 0.5-oz copper
    • Internal signal layers: 1-oz copper
  • Thermal copper ground planes beneath the thermal ball array of package containing a via farm with the following attributes
    • Thermal via quantity to ground plane = 64 (as 8x8 array)
    • Thermal via size = 0.229mm - 0.25 mm (9mils - 10 mils)
    • Thermal via plating thickness = 0.025 mm (1 mil) wall thickness

For signal integrity reasons, FR370HR or equivalent high performance epoxy laminate and repreg is also recommended.