JAJSC41E September   2015  – February 2017 DRV3205-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 改訂履歴
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Serial Peripheral Interface Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Programming
      1. 7.3.1 SPI
        1. 7.3.1.1 Address Mode Transfer
          1. 7.3.1.1.1 SPI Address Transfer Phase
        2. 7.3.1.2 SPI Data Transfer Phase
        3. 7.3.1.3 Device Data Response
    4. 7.4 Register Maps
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Three-Phase Motor Drive-Device for Automotive Application
    3. 8.3 System Example
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11デバイスおよびドキュメントのサポート
    1. 11.1 ドキュメントのサポート
      1. 11.1.1 関連資料
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 コミュニティ・リソース
    4. 11.4 商標
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 Glossary
  12. 12メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

4 改訂履歴

Changes from D Revision (November 2016) to E Revision

  • Added the propagation delay graphs to the Typical Characteristics sectionGo
  • Changed the note on the Single 8-Bit SPI Frame/Transfer figureGo
  • Updated the Typical Application Diagram figureGo

Changes from C Revision (October 2016) to D Revision

  • Changed the maximum value for the RVSET resistor error detection parameter (4.4.31) from 1.5 to 1.4 kΩ in the Electrical Characteristics tableGo
  • Changed the units and symbol for the RVSET output voltage parameter (4.4.32–4.4.34), and fixed duplicate position number for TJ = 25°C and 125°C in the Electrical Characteristics tableGo
  • Added characterization note to parameters 5.7 and 5.29 through 5.30e in the Electrical Characteristics tableGo
  • Deleted the VS voltage range test condition from the boost output voltage parameter (6.1) in the Electrical Characteristics table Go
  • Added new test condition to the switching frequency parameter (6.3) and add new values for switching frequency at VS < 6 (6.31) in the Electrical Characteristics tableGo
  • Changed the maximum value for the input pulldown resistor at EN pin parameter (7.4) from 300 to 360 kΩ in the Electrical Characteristics tableGo
  • Changed the position number for the output high and low voltage 2 parameters in the Electrical Characteristics table Go
  • Added characterization note to parameters 13.2 through 13.11 in the Serial Peripheral Interface Timing Requirements tableGo

Changes from B Revision (October 2016) to C Revision

  • Clarified the temperature for the BOOST pin quiescent current parameters (3.6B and 3.6C) and added new temperature condition (3.62B and 3.61C) in the Recommended Operating Conditions tableGo
  • Deleted the maximum value for the input hysteresis parameters (7.3 and 7.3A) in the Electrical Characteristics tableGo
  • Changed the values for the input pullup resistance parameter (7.5) in the Electrical Characteristics tableGo

Changes from A Revision (October 2016) to B Revision

  • Changed 「特長」セクションでAEC-Q1100をAEC-Q100へGo
  • Changed the maximum value for the VCC5 and VCC3 short-to-ground current from 70 to 80 mA in the Absolute Maximum Ratings tableGo
  • Changed the minimum value for the high-side/low-side driver shutdown current parameter from 7 to 2 mA in the Electrical Characteristics tableGo

Changes from * Revision (September 2016) to A Revision

  • Changed デバイスのステータスを製品プレビューから量産データへGo