JAJSD22B March   2017  – December 2018 DRV8702D-Q1 , DRV8703D-Q1

PRODUCTION DATA.  

  1. 特長
  2. アプリケーション
  3. 概要
    1.     Device Images
      1.      概略回路図
  4. 改訂履歴
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SPI Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Bridge Control
        1. 7.3.1.1 Logic Tables
      2. 7.3.2  MODE Pin
      3. 7.3.3  nFAULT Pin
      4. 7.3.4  Current Regulation
      5. 7.3.5  Amplifier Output (SO)
        1. 7.3.5.1 SO Sample and Hold Operation
      6. 7.3.6  PWM Motor Gate Drivers
        1. 7.3.6.1 Miller Charge (QGD)
      7. 7.3.7  IDRIVE Pin (DRV8702D-Q1 Only)
      8. 7.3.8  Dead Time
      9. 7.3.9  Propagation Delay
      10. 7.3.10 Overcurrent VDS Monitor
      11. 7.3.11 VDS Pin (DRV8702D-Q1 Only)
      12. 7.3.12 Charge Pump
      13. 7.3.13 Gate Drive Clamp
      14. 7.3.14 Protection Circuits
        1. 7.3.14.1 VM Undervoltage Lockout (UVLO2)
        2. 7.3.14.2 Logic Undervoltage (UVLO1)
        3. 7.3.14.3 VCP Undervoltage Lockout (CPUV)
        4. 7.3.14.4 Overcurrent Protection (OCP)
        5. 7.3.14.5 Gate Driver Fault (GDF)
        6. 7.3.14.6 Thermal Shutdown (TSD)
        7. 7.3.14.7 Watchdog Fault (WDFLT, DRV8703D-Q1 Only)
        8. 7.3.14.8 Reverse Supply Protection
      15. 7.3.15 Hardware Interface
        1. 7.3.15.1 IDRIVE (6-level input)
        2. 7.3.15.2 VDS (6-Level Input)
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1 SPI Communication
        1. 7.5.1.1 Serial Peripheral Interface (SPI)
        2. 7.5.1.2 SPI Format
    6. 7.6 Register Maps
      1. 7.6.1 DRV8703D-Q1 Memory Map
      2. 7.6.2 Status Registers
        1. 7.6.2.1 FAULT Status Register (address = 0x00h)
          1. Table 15. FAULT Status Field Descriptions
        2. 7.6.2.2 VDS and GDF Status Register Name (address = 0x01h)
          1. Table 16. VDS and GDF Status Field Descriptions
      3. 7.6.3 Control Registers
        1. 7.6.3.1 Main Control Register Name (address = 0x02h)
          1. Table 18. Main Control Field Descriptions
        2. 7.6.3.2 IDRIVE and WD Control Register Name (address = 0x03h)
          1. Table 19. IDRIVE and WD Field Descriptions
        3. 7.6.3.3 VDS Control Register Name (address = 0x04h)
          1. Table 21. VDS Control Field Descriptions
        4. 7.6.3.4 Config Control Register Name (address = 0x05h)
          1. Table 22. Config Control Field Descriptions
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 External FET Selection
        2. 8.2.2.2 IDRIVE Configuration
        3. 8.2.2.3 VDS Configuration
        4. 8.2.2.4 Current Chopping Configuration
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
    1. 9.1 Bulk Capacitance Sizing
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11デバイスおよびドキュメントのサポート
    1. 11.1 ドキュメントのサポート
      1. 11.1.1 関連資料
    2. 11.2 関連リンク
    3. 11.3 ドキュメントの更新通知を受け取る方法
    4. 11.4 コミュニティ・リソース
    5. 11.5 商標
    6. 11.6 静電気放電に関する注意事項
    7. 11.7 Glossary
  12. 12メカニカル、パッケージ、および注文情報

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • RHB|32
サーマルパッド・メカニカル・データ
発注情報

IDRIVE Pin (DRV8702D-Q1 Only)

The rise and fall times of the half-bridge output (SH pin) can be adjusted by setting the IDRIVE resistor value or forcing a voltage onto the IDRIVE pin. The FET gate voltage ramps faster if a higher IDRIVE setting is selected. The ramp of the FET gate directly affects the rise and fall times of the half-bridge output.

Tying the IDRIVE pin to ground selects the lowest drive setting of 10-mA source and 20-mA sink. Leaving this pin open selects the drive setting of 155-mA high side and 130-mA low side for source current, and 265-mA high side, 260-mA low side for sink current, at a VM voltage of 13.5 V. For a detailed list of IDRIVE configurations, see Table 6.

DRV8702D-Q1 DRV8703D-Q1 Idrive_DigitalCore_slvsdr9.gifFigure 40. IDRIVE Pin Internal Circuitry

Table 6. DRV8702D-Q1 IDRIVE Settings

IDRIVE RESISTANCE IDRIVE
VOLTAGE
SOURCE CURRENT SINK CURRENT CIRCUIT
VVM = 5.5 V VVM = 13.5 V VVM = 5.5 V VVM = 13.5 V
< 1 kΩ to GND GND High-side: 10 mA
Low-side: 10 mA
High-side: 10 mA
Low-side: 10 mA
High-side: 20 mA
Low-side: 20 mA
High-side: 20 mA
Low-side: 20 mA
DRV8702D-Q1 DRV8703D-Q1 idrive_10_20mA_slvsdr9.gif
33 kΩ ± 5% to GND 0.7 V ± 5% High-side: 20 mA
Low-side: 20 mA
High-side: 20 mA
Low-side: 20 mA
High-side: 40 mA
Low-side: 40 mA
High-side: 40 mA
Low-side: 40 mA
DRV8702D-Q1 DRV8703D-Q1 idrivepin_20_40mA_slvsdr9.gif
200 kΩ ± 5% to GND 2 V ± 5% High-side: 50 mA
Low-side: 40 mA
High-side: 50 mA
Low-side: 45 mA
High-side: 90 mA
Low-side: 85 mA
High-side: 95 mA
Low-side: 95 mA
DRV8702D-Q1 DRV8703D-Q1 idrivepin_20_40mA_slvsdr9.gif
> 2 MΩ to GND, Hi-Z 3 V ± 5% High-side: 145 mA
Low-side: 115 mA
High-side: 155 mA
Low-side: 130 mA
High-side: 250 mA
Low-side: 235 mA
High-side: 265 mA
Low-side: 260 mA
DRV8702D-Q1 DRV8703D-Q1 idrivepin_150_300mA_slvsdr9.gif
68 kΩ ± 5% to AVDD 4 V ± 5% High-side: 190 mA
Low-side: 145 mA
High-side: 210 mA
Low-side: 180 mA
High-side: 330 mA
Low-side: 300 mA
High-side: 350 mA
Low-side: 350 mA
DRV8702D-Q1 DRV8703D-Q1 idrivepin_200_400mA_slvsdr9.gif
< 1 kΩ to AVDD AVDD High-side: 240 mA
Low-side: 190 mA
High-side: 260 mA
Low-side: 225 mA
High-side: 420 mA
Low-side: 360 mA
High-side: 440 mA
Low-side:430 mA
DRV8702D-Q1 DRV8703D-Q1 idrivepin_250_500mA_slvsdr9.gif