JAJSFP2D August   2016  – September 2023 DS90UB960-Q1

PRODUCTION DATA  

  1.   1
  2. 特長
  3. アプリケーション
  4. 概要
  5. Revision History
  6. Pin Configuration and Functions
    1.     Pin Functions
  7. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  DC Electrical Characteristics
    6. 6.6  AC Electrical Characteristics
    7. 6.7  CSI-2 Timing Specifications
    8. 6.8  Recommended Timing for the Serial Control Bus
    9. 6.9  Timing Diagrams
    10. 6.10 Typical Characteristics
  8. Detailed Description
    1. 7.1 Overview
      1. 7.1.1 Functional Description
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
    4. 7.4 Device Functional Modes
      1. 7.4.1  CSI-2 Mode
      2. 7.4.2  RAW Mode
      3. 7.4.3  MODE Pin
      4. 7.4.4  REFCLK
      5. 7.4.5  Receiver Port Control
        1. 7.4.5.1 Video Stream Forwarding
      6. 7.4.6  Input Jitter Tolerance
      7. 7.4.7  Adaptive Equalizer
        1. 7.4.7.1 Transmission Distance
        2. 7.4.7.2 Channel Requirements
        3. 7.4.7.3 Adaptive Equalizer Algorithm
        4. 7.4.7.4 AEQ Settings
          1. 7.4.7.4.1 AEQ Start-Up and Initialization
          2. 7.4.7.4.2 AEQ Range
          3. 7.4.7.4.3 AEQ Timing
          4. 7.4.7.4.4 AEQ Threshold
      8. 7.4.8  Channel Monitor Loop-Through Output Driver
        1. 7.4.8.1 Code Example for CMLOUT FPD3 RX Port 0:
      9. 7.4.9  RX Port Status
        1. 7.4.9.1 RX Parity Status
        2. 7.4.9.2 FPD-Link Decoder Status
        3. 7.4.9.3 RX Port Input Signal Detection
        4. 7.4.9.4 Line Counter
        5. 7.4.9.5 Line Length
      10. 7.4.10 Sensor Status
      11. 7.4.11 GPIO Support
        1. 7.4.11.1 GPIO Input Control and Status
        2. 7.4.11.2 GPIO Output Pin Control
        3. 7.4.11.3 Forward Channel GPIO
        4. 7.4.11.4 Back Channel GPIO
        5. 7.4.11.5 GPIO Pin Status
        6. 7.4.11.6 Other GPIO Pin Controls
      12. 7.4.12 RAW Mode LV / FV Controls
      13. 7.4.13 CSI-2 Protocol Layer
      14. 7.4.14 CSI-2 Short Packet
      15. 7.4.15 CSI-2 Long Packet
      16. 7.4.16 CSI-2 Data Identifier
      17. 7.4.17 Virtual Channel and Context
      18. 7.4.18 CSI-2 Mode Virtual Channel Mapping
        1. 7.4.18.1 Example 1
        2. 7.4.18.2 Example 2:
      19. 7.4.19 CSI-2 Transmitter Frequency
      20. 7.4.20 CSI-2 Output Bandwidth
        1. 7.4.20.1 CSI-2 Output Bandwidth Calculation Example
      21. 7.4.21 CSI-2 Transmitter Status
      22. 7.4.22 Video Buffers
      23. 7.4.23 CSI-2 Line Count and Line Length
      24. 7.4.24 FrameSync Operation
        1. 7.4.24.1 External FrameSync Control
        2. 7.4.24.2 Internally Generated FrameSync
          1. 7.4.24.2.1 Code Example for Internally Generated FrameSync
      25. 7.4.25 CSI-2 Forwarding
        1. 7.4.25.1 Best-Effort Round Robin CSI-2 Forwarding
        2. 7.4.25.2 Synchronized CSI-2 Forwarding
        3. 7.4.25.3 Basic Synchronized CSI-2 Forwarding
          1. 7.4.25.3.1 Code Example for Basic Synchronized CSI-2 Forwarding
        4. 7.4.25.4 Line-Interleaved CSI-2 Forwarding
          1. 7.4.25.4.1 Code Example for Line-Interleaved CSI-2 Forwarding
        5. 7.4.25.5 Line-Concatenated CSI-2 Forwarding
          1. 7.4.25.5.1 Code Example for Line-Concatenated CSI-2 Forwarding
        6. 7.4.25.6 CSI-2 Replicate Mode
        7. 7.4.25.7 CSI-2 Transmitter Output Control
        8. 7.4.25.8 Enabling and Disabling CSI-2 Transmitters
    5. 7.5 Programming
      1. 7.5.1  Serial Control Bus
      2. 7.5.2  Second I2C Port
      3. 7.5.3  I2C Target Operation
      4. 7.5.4  Remote Target Operation
      5. 7.5.5  Remote Target Addressing
      6. 7.5.6  Broadcast Write to Remote Devices
        1. 7.5.6.1 Code Example for Broadcast Write
      7. 7.5.7  I2C Controller Proxy
      8. 7.5.8  I2C Controller Proxy Timing
        1. 7.5.8.1 Code Example for Configuring Fast-Mode Plus I2C Operation
      9. 7.5.9  Interrupt Support
        1. 7.5.9.1 Code Example to Enable Interrupts
        2. 7.5.9.2 FPD-Link III Receive Port Interrupts
        3. 7.5.9.3 Interrupts on Forward Channel GPIO
        4. 7.5.9.4 Interrupts on Change in Sensor Status
        5. 7.5.9.5 Code Example to Readback Interrupts
        6. 7.5.9.6 CSI-2 Transmit Port Interrupts
      10. 7.5.10 Error Handling
        1. 7.5.10.1 Receive Frame Threshold
        2. 7.5.10.2 Port PASS Control
      11. 7.5.11 Timestamp – Video Skew Detection
      12. 7.5.12 Pattern Generation
        1. 7.5.12.1 Reference Color Bar Pattern
        2. 7.5.12.2 Fixed Color Patterns
        3. 7.5.12.3 Pattern Generator Programming
          1. 7.5.12.3.1 Determining Color Bar Size
        4. 7.5.12.4 Code Example for Pattern Generator
      13. 7.5.13 FPD-Link BIST Mode
        1. 7.5.13.1 BIST Operation
    6. 7.6 Register Maps
      1. 7.6.1 Main Registers
      2. 7.6.2 Indirect Access Registers
        1. 7.6.2.1 PATGEN_And_CSI-2 Registers
  9. Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Power Over Coax
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 System Examples
    4. 8.4 Power Supply Recommendations
      1. 8.4.1 VDD Power Supply
      2. 8.4.2 Power-Up Sequencing
        1. 8.4.2.1 PDB Pin
        2. 8.4.2.2 System Initialization
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
        1. 8.5.1.1 Ground
        2. 8.5.1.2 Routing FPD-Link III Signal Traces and PoC Filter
        3. 8.5.1.3 CSI-2 Guidelines
      2. 8.5.2 Layout Example
  10. Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Revision History

Changes from Revision C (December 2020) to Revision D (September 2023)

  • 文書全体にわたってスペルミスと小さな書式の問題を修正Go
  • Fixed spelling errors and minor format issues throughout the document Go
  • Updated I2C pull-up resistor recommendationsGo
  • Updated Legend for Pin Functions TableGo
  • Removed the tCLK-MISS specification from the CSI-2 Timing Specifications tableGo
  • Updated Timing Diagrams section figure titles to align with the figuresGo
  • Removed obstructions in CSI-2 General Frame Format figure to make text clearerGo
  • Updated the title of the section with timing figures to Timing DiagramsGo
  • Clarified the clock speed and the configuration settings of non-synchronous clock modeGo
  • Added information about YUV supportGo
  • Added clarification that MODE pin option 0 straps the device to CSI-2 Non-Synchronous back channel and MODE pin option 4 straps the device to CSI-2 Synchronous back channelGo
  • Changed I2C terminology to "Controller" and "Target"Go
  • Updated the transmission channel requirements for Coaxial and STP/STQ Cable ApplicationsGo
  • Fixed spelling errors throughout the documentGo
  • Fixed spelling errors throughout the documentGo
  • Added information about YUV supportGo
  • Removed mention of older siliconGo
  • Added cross-links in the CSI-2 Output Bandwidth section to relevant figures in the Timing Diagrams sectionGo
  • Fixed spelling errors throughout the documentGo
  • Clarified that CSI-2 forwarding should be disabled before CSI-2 replicate mode is enabledGo
  • Added a sentence to clarify that VI2C must match the voltage applied to VDDIOGo
  • Reworded the Serial Control Bus section to reference VI2C instead of VDDIOGo
  • Added register addresses for the RX Port ID registersGo
  • Removed information suggesting that the Rx Port intended for messaging must always be selected with Register 0x4C when communicating with a remote target deviceGo
  • Corrected the total number of TargetID and TargetAlias pairs of registers for the deviceGo
  • Clarified that the write enable bit in register 0x4C needs to be set before configuring remote target addressesGo
  • Added additional information about how to configure a broadcast write to remote devicesGo
  • Removed unnecessary register writes in the Code Example for Broadcast WriteGo
  • Updated the I2C Controller Proxy descriptionGo
  • Fixed register address errors in the Typical I2C Timing Register Settings tableGo
  • Removed details about the internal reference clockGo
  • Replaced CABLE_FAULT with NO_FPD3_CLK in the interrupt readback example script to match the register bit nameGo
  • Clarified instructions for how to configure Pattern Generation on the CSI-2 PortsGo
  • Removed all RESERVED registers from the datasheetGo
  • Made register bits 0x34[5:4] public and updated the description of register bit 0x34[1]Go
  • Corrected a bit description typo for bit 4 of register 0x4AGo
  • Updated the description of register bit 0x4E[1] to clarify functionalityGo
  • Updated the description sections of registers 0x51-0x54Go
  • Fixed typos in the description for registers 0x90-0x9FGo
  • Removed RESERVED indirect register pages in the description of register bits 0xB0[5:2]Go
  • Made register 0xB6 publicGo
  • Updated the bit description of 0xB9[3:0]Go
  • Updated the name of Indirect Register Page 0 to PATGEN_AND_CSI-2Go
  • Updated the PoC descriptionGo
  • Updated all typical connection diagrams to include a reference to App Note SLVA689Go
  • Added clarification for the recommended ferrite bead characteristics on the power supply railsGo
  • Removed optional 10 kΩ pulldown resistor on Pin 4 in the Typical Connection DiagramGo
  • Updated MIPI CSI-2 D-PHY layout recommendationsGo

Changes from Revision B (Febrary 2018) to Revision C (December 2020)

  • 「特長」の箇条書き項目に「機能安全対応」を追加Go
  • Changed ESD HBM other pins to +/- 3000VGo

Changes from Revision A (Feburary 2018) to Revision B (July 2018)

  • デバイスとデータシートのステータスを制限付き「事前情報」から公開の「量産データ」に変更Go

Changes from Revision * (September 2016) to Revision A (Feburary 2018)

  • デバイスのステータスを「量産データ」から「事前情報」に変更Go
  • 動作時周囲温度範囲を-40℃~+115℃から-40℃~+105℃に変更Go
  • Combined the ESD Ratings - JEDEC and ESD Ratings - IEC and ISO tables into one tableGo
  • Removed I2C pullup voltage and maximum allowable POC noise parameter from the Recommended Operating Conditions tableGo
  • Changed the maximum operating free-air temperature from: 115℃ to: 105℃Go
  • Added a maximum value for the reference clock frequencyGo
  • Added test conditions for the total power consumption in operation modeGo
  • Changed the IDDT1 and IDDT2 parameters and added the IDDT3 parameterGo
  • Changed test conditions for the high and low level output voltagesGo
  • Removed table note for the Recommended Timing for the Serial Control Bus tableGo