SNVS639G December   2009  – December 2015 LM21305

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Synchronous DC-DC Switching Converter
      2. 8.3.2  Peak Current-Mode Control
      3. 8.3.3  Switching Frequency Setting and Synchronization
      4. 8.3.4  Light-Load Operation
      5. 8.3.5  Precision Enable
      6. 8.3.6  Device Enable, Soft-Start, and Pre-Bias Startup Capability
      7. 8.3.7  Peak Current Protection and Negative Current Limiting
      8. 8.3.8  PGOOD Indicator
      9. 8.3.9  Internal Bias Regulators
      10. 8.3.10 Minimum On-Time Considerations
    4. 8.4 Device Functional Modes
      1. 8.4.1 Overvoltage and Undervoltage Handling
      2. 8.4.2 Undervoltage Lockout (UVLO)
      3. 8.4.3 Thermal Protection
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1  Setting the Output Voltage
        2. 9.2.2.2  Calculating the Duty Cycle
        3. 9.2.2.3  Input Capacitors
        4. 9.2.2.4  AVIN Filter
        5. 9.2.2.5  Switching Frequency Selection
        6. 9.2.2.6  Filter Inductor
        7. 9.2.2.7  Output Capacitor
        8. 9.2.2.8  Efficiency Considerations
        9. 9.2.2.9  Load Current Derating When Duty Cycle Exceeds 50%
        10. 9.2.2.10 Control Loop Compensation
        11. 9.2.2.11 Compensation Components Selection
        12. 9.2.2.12 Plotting the Loop Gain
        13. 9.2.2.13 High Frequency Considerations
        14. 9.2.2.14 Bootstrap Capacitor
        15. 9.2.2.15 5V0 and 2V5 Capacitors
        16. 9.2.2.16 Maximum Ambient Temperature
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Compact PCB Layout for EMI Reduction
      2. 11.1.2 Ground Plane and Thermal Design Considerations
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Development Support
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
      2. 12.2.2 PCB Layout Resources
      3. 12.2.3 Resources for Thermal PCB Design
    3. 12.3 Community Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ

6 Pin Configuration and Functions

RSG Package
28-Pin WQFN with Exposed Thermal Pad
Top View
LM21305 30111102.gif

Pin Functions

PIN Type(1) DESCRIPTION
NAME NO.
2V5 21 P 2.5-V output of the internal LDO regulator. Bypass to AGND with a 0.1-µF ceramic capacitor. Loading this pin is not recommended.
5V0 25 P 5.0-V output of the internal LDO regulator. Bypass to PGND with a 1-µF ceramic capacitor. Loading this pin is not recommended.
AGND 14, 17–20, 24 G Analog ground for the internal bias circuitry and signal return connection for analog functions, including COMP network, frequency adjust resistor, and 2V5 decoupling capacitor.
AVIN 22, 23 P Analog power input. AVIN powers the internal 2.5-V and 5.0-V LDOs that provide bias current and internal driver power, respectively. AVIN can be connected to PVIN through a low-pass RC filter or can be supplied by a separate rail.
CBOOT 26 P High-side bootstrap connection to drive the high-side MOSFET. Connect a 100-nF bootstrap capacitor between the CBOOT and SW pins.
COMP 11 A Compensation node. This pin is an output voltage control loop error amplifier output. Connect an external compensation network to ensure stability.
EN 15 I Precision enable pin. Use an external divider to set the device turn-on threshold. If not used, connect the EN pin to AVIN.
FB 13 A Voltage feedback pin. Connect this pin to the output voltage directly or through a resistor divider to set the output voltage range.
FREQ 16 A Frequency adjust pin. Connect a resistor from FREQ to AGND to set the internal oscillator frequency. Connect FREQ to an external clock source via a coupling capacitor to synchronize to the external clock frequency.
PVIN 1, 2, 27, 28 P Input voltage to the power MOSFETs inside the device.
SW 3-6 P Switch node output of the power MOSFETs. Voltage swings from PVIN to GND on this pin. SW also delivers current to the external inductor.
PGND 7–10 G Power ground connection for the internal power switches.
PGOOD 12 OD Open-drain output with 16 μs of built-in deglitch time. If high, this status pin indicates that the output voltage is regulated within tolerance. Connect a 10-kΩ to 100-kΩ resistor to a pullup voltage source, for example the 5V0 rail or auxiliary system voltage rail.
PAD PAD — Exposed pad at the back of the device. Connect PAD to PGND, but PAD cannot be used as the primary ground connection. Use multiple vias under PAD to connect to the system ground plane for optimal thermal performance.
(1) P: Power, A: Analog, I: Digital Input, OD: Open Drain, G: Ground.