JAJSM23G December   2012  – May 2021 LM25018

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Characteristics
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Control Overview
      2. 7.3.2  VCC Regulator
      3. 7.3.3  Regulation Comparator
      4. 7.3.4  Overvoltage Comparator
      5. 7.3.5  On-Time Generator
      6. 7.3.6  Current Limit
      7. 7.3.7  N-Channel Buck Switch and Driver
      8. 7.3.8  Synchronous Rectifier
      9. 7.3.9  Undervoltage Detector
      10. 7.3.10 Thermal Protection
      11. 7.3.11 Ripple Configuration
      12. 7.3.12 Soft Start
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Application Circuit: 12.5-V to 48-V Input and 10-V, 325-mA Output Buck Converter
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Custom Design With WEBENCH® Tools
          2. 8.2.1.2.2 RFB1, RFB2
          3. 8.2.1.2.3 Frequency Selection
          4. 8.2.1.2.4 Inductor Selection
          5. 8.2.1.2.5 Output Capacitor
          6. 8.2.1.2.6 Type III Ripple Circuit
          7. 8.2.1.2.7 VCC and Bootstrap Capacitor
          8. 8.2.1.2.8 Input Capacitor
          9. 8.2.1.2.9 UVLO Resistors
      2. 8.2.2 Application Curves
      3. 8.2.3 Typical Isolated DC-DC Converter Using LM25018
        1. 8.2.3.1 Design Requirements
        2. 8.2.3.2 Detailed Design Procedure
          1. 8.2.3.2.1  Transformer Turns Ratio
          2. 8.2.3.2.2  Total IOUT
          3. 8.2.3.2.3  RFB1, RFB2
          4. 8.2.3.2.4  Frequency Selection
          5. 8.2.3.2.5  Transformer Selection
          6. 8.2.3.2.6  Primary Output Capacitor
          7. 8.2.3.2.7  Secondary Output Capacitor
          8. 8.2.3.2.8  Type III Feedback Ripple Circuit
          9. 8.2.3.2.9  Secondary Diode
          10. 8.2.3.2.10 VCC and Bootstrap Capacitor
          11. 8.2.3.2.11 Input Capacitor
          12. 8.2.3.2.12 UVLO Resistors
          13. 8.2.3.2.13 VCC Diode
        3. 8.2.3.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 Development Support
        1. 11.1.2.1 Custom Design With WEBENCH® Tools
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 サポート・リソース
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報
8.2.3.2.11 Input Capacitor

The input capacitor is typically a combination of a smaller bypass capacitor located near the regulator IC and a larger bulk capacitor. The total input capacitance must be large enough to limit the input voltage ripple to a desired amplitude. For input ripple voltage ΔVIN, CIN can be calculated using Equation 32.

Equation 32. GUID-AA5EA905-4035-444B-B21D-F65F4FF201A4-low.gif

Choosing a ΔVIN of 0.5 V gives a minimum CIN of 0.3 μF. A standard value of 0.47 μF is selected for CBYP in this design. A bulk capacitor of higher value reduces voltage spikes due to parasitic inductance between the power source to the converter. A standard value of 2.2 μF is selected for for CIN in this design. The voltage ratings of the two input capacitors must be greater than the maximum input voltage under all conditions.