JAJSCZ3A March   2017  – February 2018 LM25141-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      概略回路図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  High Voltage Start-Up Regulator
      2. 8.3.2  VCC Regulator
      3. 8.3.3  Oscillator
      4. 8.3.4  Synchronization
      5. 8.3.5  Frequency Dithering (Spread Spectrum)
      6. 8.3.6  Enable
      7. 8.3.7  Power Good
      8. 8.3.8  Output Voltage
        1. 8.3.8.1 Minimum Output Voltage Adjustment
      9. 8.3.9  Current Sense
      10. 8.3.10 DCR Current Sensing
      11. 8.3.11 Error Amplifier and PWM Comparator
      12. 8.3.12 Slope Compensation
      13. 8.3.13 Hiccup Mode Current Limiting
      14. 8.3.14 Standby Mode
      15. 8.3.15 Soft Start
      16. 8.3.16 Diode Emulation
      17. 8.3.17 High- and Low-Side Drivers
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Custom Design With WEBENCH® Tools
        2. 9.2.2.2 Inductor Calculation
        3. 9.2.2.3 Current Sense Resistor
        4. 9.2.2.4 Output Capacitor
        5. 9.2.2.5 Input Filter
          1. 9.2.2.5.1 EMI Filter Design
          2. 9.2.2.5.2 MOSFET Selection
          3. 9.2.2.5.3 Driver Slew Rate Control
          4. 9.2.2.5.4 Frequency Dithering
        6. 9.2.2.6 Control Loop
          1. 9.2.2.6.1 Feedback Compensator
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Layout Procedure
    2. 11.2 Layout Examples
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 開発サポート
        1. 12.1.1.1 WEBENCH®ツールによるカスタム設計
    2. 12.2 ドキュメントのサポート
      1. 12.2.1 関連資料
        1. 12.2.1.1 PCBレイアウトについてのリソース
        2. 12.2.1.2 熱設計についてのリソース
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 コミュニティ・リソース
    5. 12.5 商標
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.2.2.5 Input Filter

A power supply input typically has a relatively high source impedance at the switching frequency. Good-quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during the buck switch on-time. When the buck switch turns on, the current drawn from the input capacitor steps from zero to the valley of the inductor current waveform, then ramps up to the peak value, and then drops to the zero at turnoff.

Average input current can be calculated from the total input power required to support the load at VOUT:

Equation 31. LM25141-Q1 equation_30_snvsaj6.gif

The efficiency (η) is assumed to be 83% for this design example, yielding a total input power:

Equation 32. LM25141-Q1 equation_31_snvsaj6.gif
Equation 33. LM25141-Q1 equation_32_snvsaj6.gif
Equation 34. LM25141-Q1 equation_33_snvsaj6.gif

The input capacitors should be selected with sufficient RMS current rating and the maximum voltage rating.

Equation 35. LM25141-Q1 equation_34_snvsaj6.gif
Equation 36. LM25141-Q1 equation_35_snvsaj6.gif