JAJSAQ4F January   2007  – May 2021 LM5002

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 High Voltage VCC Regulator
      2. 7.3.2 Oscillator
      3. 7.3.3 External Synchronization
      4. 7.3.4 Enable and Standby
      5. 7.3.5 Error Amplifier and PWM Comparator
      6. 7.3.6 Current Amplifier and Slope Compensation
      7. 7.3.7 Power MOSFET
    4. 7.4 Device Functional Modes
      1. 7.4.1 Thermal Protection
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 VIN
      2. 8.1.2 SW PIN
      3. 8.1.3 EN or UVLO Voltage Divider Selection
      4. 8.1.4 Soft Start
    2. 8.2 Typical Applications
      1. 8.2.1 Non-Isolated Flyback Regulator
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Switching Frequency
          2. 8.2.1.2.2 Flyback Transformer
          3. 8.2.1.2.3 Peak MOSFET Current
          4. 8.2.1.2.4 Output Capacitance
          5. 8.2.1.2.5 Output Diode Rating
          6. 8.2.1.2.6 Power Stage Analysis
          7. 8.2.1.2.7 Loop Compensation
      2. 8.2.2 Isolated Flyback Regulator
        1. 8.2.2.1 Design Requirements
      3. 8.2.3 Boost Regulator
        1. 8.2.3.1 Design Requirements
      4. 8.2.4 24-V SEPIC Regulator
        1. 8.2.4.1 Design Requirements
      5. 8.2.5 12-V Automotive SEPIC Regulator
        1. 8.2.5.1 Design Requirements
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 サポート・リソース
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報
8.2.1.2.2 Flyback Transformer

Two things require consideration when specifying a flyback transformer. First, the turns ratio to determine the duty cyle D (MOSFET on-time compared to the switching period). Second, the primary inductance (LPRI) to determine the current sense ramp for current-mode control.

To start, the primary inductance in continous current mode (CCM) is designed to provide a ramp during the MOSFET on-time of around 30% of the full load MOSFET current. This produces a good signal-to-noise ratio for current mode control.

The transfer function of a flyback power stage is Equation 4.

Equation 4. GUID-9DB2B009-3FA2-44BA-8270-4BACBCF0102F-low.gif

where:

  • VIN is the input voltage
  • VOUT is the secondary output voltage
  • D is the duty cycle of the MOSFET for one switching cycle
  • NPRI is the number of turns on the primary winding of the transformer
  • NSEC is the number of turns on the secondary winding of the transformer

The duty cycle can be derived as shown in Equation 5.

Equation 5. GUID-ADA99BAB-22ED-4B81-8E65-50CE743E0D9A-low.gif

And the approximate turns ratio is given by Equation 6.

Equation 6. GUID-B500A8DD-7B61-4E82-A20C-1B0053E1BE1A-low.gif

The primary inducance (LPRI) is calculated using Equation 7.

Equation 7. GUID-18647079-AE76-496C-859B-D1F486853513-low.gif

where:

  • LPRI is the transformer inductance referenced to the primary side
  • RR is the ripple ratio of the reflected secondary output current (ypically between 30% and 40%)

The auxillary winding turns ratio can be found with Equation 8.

Equation 8. GUID-EC23950B-91CB-4484-B752-38BE58F128CE-low.gif

where:

  • NAUX is the number of turns on the auxiliary winding of the transformer
  • VAUX is the desired VCC voltage

The CCM duty cycle can be designed for 50% with minimum input voltage. Using Equation 6, the turns ratio of the secondary winding to the primay winding can be found to be 0.313. Rounding to a whole number of turns results in a turns ratio of 0.375. The auxillary winding of the transformer can be used to supply the VCC voltage to the LM5002, resulting in better total efficiency by disabling the internal high voltage VCC regulator. To disable the VCC regulator the exteranlly supplied voltage must be greater than 7 V, thus a target voltage of 8 V is selected. The number of turns on the auxillary winding can be found with Equation 8, resulting in a turns ratio of the auxillary winding to the secondary winding of 0.6.

The primary inductance can now be solved for using Equation 7. Assuming that VIN is at the minimum specified value and the ripple ratio (RR) is 35% the primary inductance is calculated to be 217 µH. Based on avaliable transformers a 300 µH primary inductance was selected.