JAJSF96C April   2018  – October 2021 LM5036

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  High-Voltage Start-Up Regulator
      2. 7.3.2  Undervoltage Lockout (UVLO)
      3. 7.3.3  Reference Regulator
      4. 7.3.4  Oscillator, Synchronized Input
      5. 7.3.5  Voltage-Mode Control
      6. 7.3.6  Primary-Side Gate Driver Outputs (LSG and HSG)
      7. 7.3.7  Half-Bridge PWM Scheme
      8. 7.3.8  Maximum Duty Cycle Operation
      9. 7.3.9  Pre-Biased Start-Up Process
        1. 7.3.9.1 Primary FETs Soft-Start Process
        2. 7.3.9.2 Synchronous Rectifier (SR) Soft-Start Process
      10. 7.3.10 Zero Duty Cycle Operation
      11. 7.3.11 Enhanced Cycle-by-Cycle Current Limiting with Pulse Matching
      12. 7.3.12 Reverse Current Protection
      13. 7.3.13 CBC Threshold Accuracy
      14. 7.3.14 Hiccup Mode Protection
      15. 7.3.15 Hiccup Mode Blanking
      16. 7.3.16 Over-Temperature Protection (OTP)
      17. 7.3.17 Over-Voltage / Latch (ON_OFF Pin)
      18. 7.3.18 Auxiliary Constant On-Time Control
      19. 7.3.19 Auxiliary On-Time Generator
      20. 7.3.20 Auxiliary Supply Current Limiting
      21. 7.3.21 Auxiliary Primary Output Capacitor Ripple
      22. 7.3.22 Auxiliary Ripple Configuration and Control
      23. 7.3.23 Asynchronous Mode Operation of Auxiliary Supply
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Custom Design With WEBENCH® Tools
        2. 8.2.2.2  Input Transient Protection
        3. 8.2.2.3  Level-Shift Detection Circuit
        4. 8.2.2.4  Applications with VIN > 100-V
        5. 8.2.2.5  Applications without Pre-Biased Start-Up Requirement
        6. 8.2.2.6  UVLO Voltage Divider Selection
        7. 8.2.2.7  Over Voltage, Latch (ON_OFF Pin) Voltage Divider Selection
        8. 8.2.2.8  SS Capacitor
        9. 8.2.2.9  SSSR Capacitor
        10. 8.2.2.10 Half-Bridge Power Stage Design
        11. 8.2.2.11 Current Limit
        12. 8.2.2.12 Auxiliary Transformer
        13. 8.2.2.13 Auxiliary Feedback Resistors
        14. 8.2.2.14 RON Resistor
        15. 8.2.2.15 VIN Pin Capacitor
        16. 8.2.2.16 Auxiliary Primary Output Capacitor
        17. 8.2.2.17 Auxiliary Secondary Output Capacitor
        18. 8.2.2.18 Auxiliary Feedback Ripple Circuit
        19. 8.2.2.19 Auxiliary Secondary Diode
        20. 8.2.2.20 VCC Diode
        21. 8.2.2.21 Opto-Coupler Interface
        22. 8.2.2.22 Full-Bridge Converter Applications
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Custom Design With WEBENCH® Tools
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
        1. 11.2.1.1 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.12 Reverse Current Protection

In addition to the CBC current limit, a negative current limit, which is set to be half of the positive current limit as shown in Figure 7-15. This is used to prevent excessive reverse current which could cause significant output voltage dip and potentially damage the power converter. When the negative current limit is exceeded twice, the SSSR capacitor will be clamped to ground so the controller enters the SR SYNC mode where the SR pulses are synchronized to the respective primary FET pulses. Therefore, the SR freewheeling pulses are turned off. The negative current limit event counter will be reset if the number of negative current limit events detected within four switching periods is less than two.

GUID-5F825E16-3E41-4F72-8E42-FEC985859081-low.gifFigure 7-15 Reverse Current Protection Circuit

At the trip threshold of the NEG comparator both inputs are at the same potential. In this case the voltage on the CS_NEG pin is expressed by Equation 15.

Equation 15. GUID-D55E89EE-5446-40F3-B64C-483B699A7177-low.gif

The voltage across the CS resistor at the trip threshold of the NEG comparator can therefore be determined by combining Equation 9, Equation 11 and Equation 15.

Equation 16. GUID-594E2C94-7AC3-4ADC-A585-84D896FB2AB0-low.gif

Notice that the inductor current has its most negative value at the start of the LSG on period. The NEG comparator trip will occur immediately after the blanking period (tCSBLK) has expired.

The Excel Calculator Tool predicts both the positive and negative output current limit levels as a function of input voltage for a given set of resistor values.