JAJSF96C April   2018  – October 2021 LM5036

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  High-Voltage Start-Up Regulator
      2. 7.3.2  Undervoltage Lockout (UVLO)
      3. 7.3.3  Reference Regulator
      4. 7.3.4  Oscillator, Synchronized Input
      5. 7.3.5  Voltage-Mode Control
      6. 7.3.6  Primary-Side Gate Driver Outputs (LSG and HSG)
      7. 7.3.7  Half-Bridge PWM Scheme
      8. 7.3.8  Maximum Duty Cycle Operation
      9. 7.3.9  Pre-Biased Start-Up Process
        1. 7.3.9.1 Primary FETs Soft-Start Process
        2. 7.3.9.2 Synchronous Rectifier (SR) Soft-Start Process
      10. 7.3.10 Zero Duty Cycle Operation
      11. 7.3.11 Enhanced Cycle-by-Cycle Current Limiting with Pulse Matching
      12. 7.3.12 Reverse Current Protection
      13. 7.3.13 CBC Threshold Accuracy
      14. 7.3.14 Hiccup Mode Protection
      15. 7.3.15 Hiccup Mode Blanking
      16. 7.3.16 Over-Temperature Protection (OTP)
      17. 7.3.17 Over-Voltage / Latch (ON_OFF Pin)
      18. 7.3.18 Auxiliary Constant On-Time Control
      19. 7.3.19 Auxiliary On-Time Generator
      20. 7.3.20 Auxiliary Supply Current Limiting
      21. 7.3.21 Auxiliary Primary Output Capacitor Ripple
      22. 7.3.22 Auxiliary Ripple Configuration and Control
      23. 7.3.23 Asynchronous Mode Operation of Auxiliary Supply
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Custom Design With WEBENCH® Tools
        2. 8.2.2.2  Input Transient Protection
        3. 8.2.2.3  Level-Shift Detection Circuit
        4. 8.2.2.4  Applications with VIN > 100-V
        5. 8.2.2.5  Applications without Pre-Biased Start-Up Requirement
        6. 8.2.2.6  UVLO Voltage Divider Selection
        7. 8.2.2.7  Over Voltage, Latch (ON_OFF Pin) Voltage Divider Selection
        8. 8.2.2.8  SS Capacitor
        9. 8.2.2.9  SSSR Capacitor
        10. 8.2.2.10 Half-Bridge Power Stage Design
        11. 8.2.2.11 Current Limit
        12. 8.2.2.12 Auxiliary Transformer
        13. 8.2.2.13 Auxiliary Feedback Resistors
        14. 8.2.2.14 RON Resistor
        15. 8.2.2.15 VIN Pin Capacitor
        16. 8.2.2.16 Auxiliary Primary Output Capacitor
        17. 8.2.2.17 Auxiliary Secondary Output Capacitor
        18. 8.2.2.18 Auxiliary Feedback Ripple Circuit
        19. 8.2.2.19 Auxiliary Secondary Diode
        20. 8.2.2.20 VCC Diode
        21. 8.2.2.21 Opto-Coupler Interface
        22. 8.2.2.22 Full-Bridge Converter Applications
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Custom Design With WEBENCH® Tools
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
        1. 11.2.1.1 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.2.2.7 Over Voltage, Latch (ON_OFF Pin) Voltage Divider Selection

As described in Section 7.3.17, the ON_OFF pin can be configured as a latch pin or an OVP pin. Figure 7-20 shows the latch configuration. The ON_OFF pin is latched when the pin voltage reaches IOVL × RL when any of the internal faults is detected. The latch diode is reverse-biased during latch operation. Select the latch resistor RL value such that IOVL × RL > VON_OFF. This design example uses an RL value of 49.9 kΩ. If the latch threshold is 80 V, use an ROV1 value of 40 kΩ, and use an ROV2 value of 710 Ω.

If the ON_OFF pin is configured as an OVP pin, two resistors can be used to program the maximum operating input voltage for the half-bridge converter, as illustrated in Figure 7-21. When the ON_OFF pin voltage rises above the VON_OFF threshold, an internal current source IOVL is enabled to raise the ON_OFF pin voltage, thus providing the threshold hysteresis. Use Equation 29 and Equation 30 to determine resistance values for ROV1 and ROV2. If the LM5036 controller is to be disabled when VIN rises above 80 V and enabled when it falls below 78 V. Use an ROV1 value of 40-kΩ, and an ROV2 value of 635-Ω. The ON_OFF pin can also be used for external thermal protection with a thermistor.