JAJSKQ9B December   2021  – December 2022 LM5123-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 概要 (続き)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Device Enable/Disable (EN, VH Pin)
      2. 8.3.2  High Voltage VCC Regulator (BIAS, VCC Pin)
      3. 8.3.3  Light Load Switching Mode Selection (MODE Pin)
      4. 8.3.4  VOUT Range Selection (RANGE Pin)
      5. 8.3.5  Line Undervoltage Lockout (UVLO Pin)
      6. 8.3.6  Fast Restart using VCC HOLD (VH Pin)
      7. 8.3.7  Adjustable Output Regulation Target (VOUT, TRK, VREF Pin)
      8. 8.3.8  Overvoltage Protection (VOUT Pin)
      9. 8.3.9  Power Good Indicator (PGOOD Pin)
      10. 8.3.10 Dynamically Programmable Switching Frequency (RT)
      11. 8.3.11 External Clock Synchronization (SYNC Pin)
      12. 8.3.12 Programmable Spread Spectrum (DITHER Pin)
      13. 8.3.13 Programmable Soft Start (SS Pin)
      14. 8.3.14 Wide Bandwidth Transconductance Error Amplifier and PWM (TRK, COMP Pin)
      15. 8.3.15 Current Sensing and Slope Compensation (CSP, CSN Pin)
      16. 8.3.16 Constant Peak Current Limit (CSP, CSN Pin)
      17. 8.3.17 Maximum Duty Cycle and Minimum Controllable On-Time Limits
      18. 8.3.18 Deep Sleep Mode and Bypass Operation (HO, CP Pin)
      19. 8.3.19 MOSFET Drivers, Integrated Boot Diode, and Hiccup Mode Fault Protection (LO, HO, HB Pin)
      20. 8.3.20 Thermal Shutdown Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Device Status
        1. 8.4.1.1 Shutdown Mode
        2. 8.4.1.2 Configuration Mode
        3. 8.4.1.3 Active Mode
        4. 8.4.1.4 Sleep Mode
        5. 8.4.1.5 Deep Sleep Mode
      2. 8.4.2 Light Load Switching Mode
        1. 8.4.2.1 Forced PWM (FPWM) Mode
        2. 8.4.2.2 Diode Emulation (DE) Mode
        3. 8.4.2.3 Forced Diode Emulation Operation in FPWM Mode
        4. 8.4.2.4 Skip Mode
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Application Ideas
      3. 9.2.3 Application Curves
    3. 9.3 System Example
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 サポート・リソース
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • RGR|20
サーマルパッド・メカニカル・データ
発注情報

8.4.1.5 Deep Sleep Mode

When SS is greater than 1.5 V, the device enters deep sleep mode after four cycles in OVP status. During deep sleep mode, the device stops the internal oscillator to reduce the operating current, disables UVLO comparator, disables the error amplifier, and parks the COMP pin at 0.25 V.

In FPWM or DE mode, the device re-enters active mode if VOUT falls down below VOVTH. In skip mode, the device re-enters active mode if VOUT falls down below VOVTH, then immediately enters sleep mode after 16 consecutive cycles of pulse skipping.