SNOSB31J July   2009  – December 2014 LMX2541

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
      1. 7.7.1 Not Ensured Characteristics
      2. 7.7.2 Output Power in Bypass Mode
      3. 7.7.3 Output Power in Divided Mode
      4. 7.7.4 RFout Output Impedance
        1. 7.7.4.1 OSCin and Fin Sensitivity
  8. Parameter Measurement Information
    1. 8.1 Bench Test Setups
      1. 8.1.1 Charge Pump Current Measurements
      2. 8.1.2 Charge Pump Current Definitions
        1. 8.1.2.1 Charge Pump Current Definitions
        2. 8.1.2.2 Variation of Charge Pump Current Magnitude vs. Charge Pump Voltage
        3. 8.1.2.3 Variation of Charge Pump Current Magnitude vs. Temperature
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Feature Description
      1. 9.3.1  PLL Reference Oscillator Input Pins
      2. 9.3.2  PLL R Divider
      3. 9.3.3  PLL Phase Detector and Charge Pump
      4. 9.3.4  PLL N Divider and Fractional Circuitry
      5. 9.3.5  Partially Integrated Loop Filter
      6. 9.3.6  Low Noise, Fully Integrated VCO
      7. 9.3.7  Programmable VCO Divider
      8. 9.3.8  Programmable RF Output Buffer
      9. 9.3.9  Powerdown Modes
      10. 9.3.10 Fastlock
      11. 9.3.11 Lock Detect
      12. 9.3.12 Current Consumption
      13. 9.3.13 Fractional Spurs
        1. 9.3.13.1 Primary Fractional Spurs
        2. 9.3.13.2 Sub-Fractional Spurs
      14. 9.3.14 Impact of VCO_DIV on Fractional Spurs
      15. 9.3.15 PLL Phase Noise
        1. 9.3.15.1 , LMX2541SQ3740E Raw Phase Noise Measurement Plot Description
        2. 9.3.15.2 , LMX2541SQ2690 System Phase Noise Plot Description
        3. 9.3.15.3 Phase Noise of PLL
      16. 9.3.16 Impact of Modulator Order, Dithering, and Larger Equivalent Fractions on Spurs and Phase Noise
      17. 9.3.17 Modulator Order
      18. 9.3.18 Programmable Output Power with On/Off
      19. 9.3.19 Loop Filter
      20. 9.3.20 Internal VCO Digital Calibration Time
    4. 9.4 Device Functional Modes
      1. 9.4.1 External VCO Mode
      2. 9.4.2 Digital FSK Mode
    5. 9.5 Programming
      1. 9.5.1 General Programming Information
    6. 9.6 Register Maps
      1. 9.6.1 Register R7
        1. 9.6.1.1  Register R13
          1. 9.6.1.1.1 VCO_DIV_OPT[2:0]
        2. 9.6.1.2  Register R12
        3. 9.6.1.3  Register R9
        4. 9.6.1.4  Register R8
          1. 9.6.1.4.1 AC_TEMP_COMP[4:0]
        5. 9.6.1.5  Register R6
          1. 9.6.1.5.1 RFOUT[1:0] - RFout enable pin
          2. 9.6.1.5.2 DIVGAIN[3:0], VCOGAIN[3:0], and OUTTERM[3:0] - Power Controls for RFout
        6. 9.6.1.6  Register R5
          1. 9.6.1.6.1 FL_TOC[13:0] -- Time Out Counter for FastLock
          2. 9.6.1.6.2 FL_R3_LF[2:0] -- Value for Internal Loop Filter Resistor R3 During Fastlock
          3. 9.6.1.6.3 FL_R4_LF[2:0] -- Value for Internal Loop Filter Resistor R4 During Fastlock
          4. 9.6.1.6.4 FL_CPG[4:0] -- Charge Pump Current for Fastlock
        7. 9.6.1.7  Register R4
          1. 9.6.1.7.1 OSC_FREQ [7:0] -- OSCin Frequency for VCO Calibration Clocking
          2. 9.6.1.7.2 VCO_DIV[5:0] - VCO Divider
          3. 9.6.1.7.3 R3_LF[2:0] -- Value for Internal Loop Filter Resistor R3
          4. 9.6.1.7.4 R4_LF[2:0] -- Value for Internal Loop Filter Resistor R4
          5. 9.6.1.7.5 C3_LF[3:0] -- Value for C3 in the Internal Loop Filter
          6. 9.6.1.7.6 C4_LF[3:0] -- Value for C4 in the Internal Loop Filter
        8. 9.6.1.8  Register R3
          1. 9.6.1.8.1  MODE[1:0] -- Operational Mode
          2. 9.6.1.8.2  Powerdown -- Powerdown Bit
          3. 9.6.1.8.3  XO - Crystal Oscillator Mode Select
          4. 9.6.1.8.4  CPG[4:0] -- Charge Pump Current
          5. 9.6.1.8.5  MUX[3:0] -- Multiplexed Output for Ftest/LD Pin
          6. 9.6.1.8.6  CPP - Charge Pump Polarity
          7. 9.6.1.8.7  OSC2X-- OSCin Frequency Doubler
          8. 9.6.1.8.8  FDM - Extended Fractional Denominator Mode Enable
          9. 9.6.1.8.9  ORDER[2:0] -- Delta-Sigma Modulator Order
          10. 9.6.1.8.10 DITH[1:0] -- Dithering
          11. 9.6.1.8.11 CPT - Charge Pump TRI-STATE
          12. 9.6.1.8.12 DLOCK[2:0] - Controls for Digital Lock Detect
          13. 9.6.1.8.13 FSK - Frequency Shift Keying
        9. 9.6.1.9  Register R2
          1. 9.6.1.9.1 PLL_DEN[21:0] -- Fractional Denominator
        10. 9.6.1.10 Registers R1 and R0
          1. 9.6.1.10.1 PLL_R[11:0] -- PLL R Divider Value
          2. 9.6.1.10.2 PLL_N[17:0] PLL N Divider Value
          3. 9.6.1.10.3 PLL_NUM[21:0] -- Fractional Numerator
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Determining the Best Frequency Option of the LMX2541 to Use
      2. 10.1.2 RFout Output Power Test Setup
      3. 10.1.3 Phase Noise Measurement Test Setup
        1. 10.1.3.1 PLL Phase Noise Measurement
          1. 10.1.3.1.1 PLL Phase Noise Measurement - 1/f Noise
          2. 10.1.3.1.2 PLL Phase Noise Measurement - Flat Noise
        2. 10.1.3.2 VCO Phase Noise Measurement
        3. 10.1.3.3 Divider Phase Noise Measurement
      4. 10.1.4 Input and Output Impedance Test Setup
        1. 10.1.4.1 OSCin Input Impedance Measurement
        2. 10.1.4.2 ExtVCOin Input Impedance Measurement
        3. 10.1.4.3 RFout Output Impedance Measurement
      5. 10.1.5 ExtVCOin (NOT OSCin) Input Sensitivity Test Setup
      6. 10.1.6 OSCin Input Sensitivity Test Setup
        1. 10.1.6.1 Input Sensitivity Test Procedure
        2. 10.1.6.2 OSCin Slew Rate Tests
      7. 10.1.7 Typical Connections
        1. 10.1.7.1 Full Chip Mode, Differential OSCin
        2. 10.1.7.2 External VCO Mode, Single-Ended OSCin, RFout Pin not Used
        3. 10.1.7.3 OSCin/OSCin* Connections
          1. 10.1.7.3.1 Single-Ended Operation
          2. 10.1.7.3.2 Differential Operation
          3. 10.1.7.3.3 Crystal Mode Operation
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Configuring the LMX2541 for Optimal Performance
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
    2. 13.2 Trademarks
    3. 13.3 Electrostatic Discharge Caution
    4. 13.4 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • NJK|36
サーマルパッド・メカニカル・データ
発注情報

6 Pin Configuration and Functions

NJK Package
36-Pin WQFN
Top View
LMX2541 30073302.gif

Pin Functions

PIN TYPE DESCRIPTION
NAME NO.
Bypass 30 Bypass Put a cap to the VccBias pin.
CE 11 CMOS Chip Enable.
The device needs to be programmed for this pin to properly power down the device.
CLK 33 High-Z Input MICROWIRE clock input. High impedance CMOS input.
This pin is used for the digital FSK modulation feature.
CPout 16 Output Charge pump output.
DATA 32 High-Z Input MICROWIRE serial data input. High impedance CMOS input.
ExtVCOin 12 RF Input Optional input for use with an external VCO.
This pin should be AC coupled if used or left open if not used.
FLout 17 Output Fastlock output.
Ftest/LD 20 Output Software controllable multiplexed CMOS output.
Can be used to monitor PLL lock condition.
GND 0 GND The DAP pad must be grounded.
GND 1 GND
GND 10 GND
GND 27 GND
L1 4 NC Do not connect this pin.
L2 6 NC Do not connect this pin.
LE 34 High-Z Input MICROWIRE Latch Enable input. High impedance CMOS input.
Lmid 5 NC Do not connect this pin.
NC 35 NC No connect.
OSCin 21 High-Z Input Oscillator input signal. If not being used with an external crystal, this input should be AC coupled.
OSCin* 22 High-Z Input Complementary oscillator input signal. Can also be used with an external crystal. If not being used with an external crystal, this input should be AC coupled.
RFout 36 RF Output RF output. Must be AC coupled if used.
RFoutEN 24 Input Software programmable output enable pin.
VccBias 29 Supply Supply for Bias circuitry that is for the whole chip.
VccCP1 14 Supply Power supply for PLL charge pump.
VccCP2 18 Supply Power supply for PLL charge pump.
VccDig 28 Supply Supply for digital circuitry, such the MICROWIRE.
VccDiv 31 Supply Supply for the output divider
VccFRAC 25 Supply
(LDO Input)
Power Supply for the PLL fractional circuitry.
VccOSCin 23 Supply Supply for the OSCin buffer.
VccPLL1 13 Supply Power supply for PLL.
VccPLL2 19 Supply Power supply for PLL.
VccRFout 3 Supply
(LDO Input)
Supply for the RF output buffer.
VccVCO 7 Supply
(LDO Input)
Supply for the VCO.
VregFRAC 26 LDO Output Regulated power supply used for the fractional delta-sigma circuitry.
VregRFout 2 LDO Output LDO Output for RF output buffer.
VrefVCO 9 LDO Bypass LDO Bypass
VregVCO 8 LDO Output LDO Output for VCO
Vtune 15 High-Z Input Tuning voltage input to the VCO.