JAJSF48 March   2018 LP87561-Q1 , LP87562-Q1 , LP87563-Q1 , LP87564-Q1 , LP87565-Q1

PRODUCTION DATA.  

  1. 特長
  2. アプリケーション
  3. 概要
    1.     効率と出力電流との関係
  4. 改訂履歴
  5. Device Comparison Table
  6. Pin Configuration and Functions
    1.     Pin Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 I2C Serial Bus Timing Requirements
    7. 7.7 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Descriptions
      1. 8.3.1 Multi-Phase DC/DC Converters
        1. 8.3.1.1 Overview
        2. 8.3.1.2 Multiphase Operation, Phase Adding, and Phase-Shedding
        3. 8.3.1.3 Transition Between PWM and PFM Modes
        4. 8.3.1.4 Multiphase Switcher Configurations
        5. 8.3.1.5 Buck Converter Load-Current Measurement
        6. 8.3.1.6 Spread-Spectrum Mode
      2. 8.3.2 Sync Clock Functionality
      3. 8.3.3 Power-Up
      4. 8.3.4 Regulator Control
        1. 8.3.4.1 Enabling and Disabling Regulators
        2. 8.3.4.2 Changing Output Voltage
      5. 8.3.5 Enable and Disable Sequences
      6. 8.3.6 Device Reset Scenarios
      7. 8.3.7 Diagnosis and Protection Features
        1. 8.3.7.1 Power-Good Information (PGOOD Pin)
        2. 8.3.7.2 Warnings for Diagnosis (Interrupt)
          1. 8.3.7.2.1 Output Power Limit
          2. 8.3.7.2.2 Thermal Warning
        3. 8.3.7.3 Protection (Regulator Disable)
          1. 8.3.7.3.1 Short-Circuit and Overload Protection
          2. 8.3.7.3.2 Overvoltage Protection
          3. 8.3.7.3.3 Thermal Shutdown
        4. 8.3.7.4 Fault (Power Down)
          1. 8.3.7.4.1 Undervoltage Lockout
      8. 8.3.8 GPIO Signal Operation
      9. 8.3.9 Digital Signal Filtering
    4. 8.4 Device Functional Modes
      1. 8.4.1 Modes of Operation
    5. 8.5 Programming
      1. 8.5.1 I2C-Compatible Interface
        1. 8.5.1.1 Data Validity
        2. 8.5.1.2 Start and Stop Conditions
        3. 8.5.1.3 Transferring Data
        4. 8.5.1.4 I2C-Compatible Chip Address
        5. 8.5.1.5 Auto-Increment Feature
    6. 8.6 Register Maps
      1. 8.6.1 Register Descriptions
        1. 8.6.1.1  OTP_REV
        2. 8.6.1.2  BUCK0_CTRL1
        3. 8.6.1.3  BUCK0_CTRL2
        4. 8.6.1.4  BUCK1_CTRL1
        5. 8.6.1.5  BUCK1_CTRL2
        6. 8.6.1.6  BUCK2_CTRL1
        7. 8.6.1.7  BUCK2_CTRL2
        8. 8.6.1.8  BUCK3_CTRL1
        9. 8.6.1.9  BUCK3_CTRL2
        10. 8.6.1.10 BUCK0_VOUT
        11. 8.6.1.11 BUCK0_FLOOR_VOUT
        12. 8.6.1.12 BUCK1_VOUT
        13. 8.6.1.13 BUCK1_FLOOR_VOUT
        14. 8.6.1.14 BUCK2_VOUT
        15. 8.6.1.15 BUCK2_FLOOR_VOUT
        16. 8.6.1.16 BUCK3_VOUT
        17. 8.6.1.17 BUCK3_FLOOR_VOUT
        18. 8.6.1.18 BUCK0_DELAY
        19. 8.6.1.19 BUCK1_DELAY
        20. 8.6.1.20 BUCK2_DELAY
        21. 8.6.1.21 BUCK3_DELAY
        22. 8.6.1.22 GPIO2_DELAY
        23. 8.6.1.23 GPIO3_DELAY
        24. 8.6.1.24 RESET
        25. 8.6.1.25 CONFIG
        26. 8.6.1.26 INT_TOP1
        27. 8.6.1.27 INT_TOP2
        28. 8.6.1.28 INT_BUCK_0_1
        29. 8.6.1.29 INT_BUCK_2_3
        30. 8.6.1.30 TOP_STAT
        31. 8.6.1.31 BUCK_0_1_STAT
        32. 8.6.1.32 BUCK_2_3_STAT
        33. 8.6.1.33 TOP_MASK1
        34. 8.6.1.34 TOP_MASK2
        35. 8.6.1.35 BUCK_0_1_MASK
        36. 8.6.1.36 BUCK_2_3_MASK
        37. 8.6.1.37 SEL_I_LOAD
        38. 8.6.1.38 I_LOAD_2
        39. 8.6.1.39 I_LOAD_1
        40. 8.6.1.40 PGOOD_CTRL1
        41. 8.6.1.41 PGOOD_CTRL2
        42. 8.6.1.42 PGOOD_FLT
        43. 8.6.1.43 PLL_CTRL
        44. 8.6.1.44 PIN_FUNCTION
        45. 8.6.1.45 GPIO_CONFIG
        46. 8.6.1.46 GPIO_IN
        47. 8.6.1.47 GPIO_OUT
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Inductor Selection
        2. 9.2.1.2 Input Capacitor Selection
        3. 9.2.1.3 Output Capacitor Selection
        4. 9.2.1.4 Snubber Components
        5. 9.2.1.5 Supply Filtering Components
        6. 9.2.1.6 Current Limit vs. Maximum Output Current
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デベロッパー・ネットワークの製品に関する免責事項
    2. 12.2 ドキュメントのサポート
    3. 12.3 関連リンク
    4. 12.4 ドキュメントの更新通知を受け取る方法
    5. 12.5 コミュニティ・リソース
    6. 12.6 商標
    7. 12.7 静電気放電に関する注意事項
    8. 12.8 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • RNF|26
サーマルパッド・メカニカル・データ
発注情報

I2C Serial Bus Timing Requirements

These specifications are ensured by design. VIN_Bx = 3.7 V, unless otherwise noted.
MIN MAX UNIT
ƒSCL Serial clock frequency Standard mode 100 kHz
Fast mode 400
Fast mode+ 1 MHz
High-speed mode, Cb = 100 pF 3.4
High-speed mode, Cb = 400 pF 1.7
tLOW SCL low time Standard mode 4.7 µs
Fast mode 1.3
Fast mode+ 0.5
High-speed mode, Cb = 100 pF 160 ns
High-speed mode, Cb = 400 pF 320
tHIGH SCL high time Standard mode 4 µs
Fast mode 0.6
Fast mode+ 0.26
High-speed mode, Cb = 100 pF 60 ns
High-speed mode, Cb = 400 pF 120
tSU;DAT Data setup time Standard mode 250 ns
Fast mode 100
Fast mode+ 50
High-speed mode 10
tHD;DAT Data hold time Standard mode 10 3450 ns
Fast mode 10 900
Fast mode+ 10
High-speed mode, Cb = 100 pF 10 70 ns
High-speed mode, Cb = 400 pF 10 150
tSU;STA Setup time for a start or a repeated start condition Standard mode 4.7 µs
Fast mode 0.6
Fast mode+ 0.26
High-speed mode 160 ns
tHD;STA Hold time for a start or a repeated start condition Standard mode 4 µs
Fast mode 0.6
Fast mode+ 0.26
High-speed mode 160 ns
tBUF Bus free time between a stop and start condition Standard mode 4.7 µs
Fast mode 1.3
Fast mode+ 0.5
tSU;STO Setup time for a stop condition Standard mode 4 µs
Fast mode 0.6
Fast mode+ 0.26
High-speed mode 160 ns
trDA Rise time of SDA signal Standard mode 1000 ns
Fast mode 20 300
Fast mode+ 120
High-speed mode, Cb = 100 pF 10 80
High-speed mode, Cb = 400 pF 20 160
tfDA Fall time of SDA signal Standard mode 300 ns
Fast mode 20 × (VDD / 5.5 V) 300
Fast mode+ 20 × (VDD / 5.5 V) 120
High-speed mode, Cb = 100 pF 10 80
High-speed mode, Cb = 400 pF 30 160
trCL Rise time of SCL signal Standard mode 1000 ns
Fast mode 20 300
Fast mode+ 120
High-speed mode, Cb = 100 pF 10 40
High-speed mode, Cb = 400 pF 20 80
trCL1 Rise time of SCL signal after a repeated start condition and after an acknowledge bit High-speed mode, Cb = 100 pF 10 80 ns
High-speed mode, Cb = 400 pF 20 160
tfCL Fall time of a SCL signal Standard mode 300 ns
Fast mode 20 × (VDD / 5.5 V) 300
Fast mode+ 20 × (VDD / 5.5 V) 120
High-speed mode, Cb = 100 pF 10 40
High-speed mode, Cb = 400 pF 20 80
Cb Capacitive load for each bus line (SCL and SDA) 400 pF
tSP Pulse width of spike suppressed (SCL and SDA spikes that are less than the indicated width are suppressed) Standard mode, fast mode and fast mode+ 50 ns
High-speed mode 10
LP87561-Q1 LP87562-Q1 LP87563-Q1 LP87564-Q1 LP87565-Q1 30190619.gifFigure 1. I2C Timing