JAJSJ40M June 2007 – March 2022 MSP430F2416 , MSP430F2417 , MSP430F2418 , MSP430F2419 , MSP430F2616 , MSP430F2617 , MSP430F2618 , MSP430F2619
PRODUCTION DATA
- 1 特長
- 2 アプリケーション
- 3 概要
- 4 機能ブロック図
- 5 Revision History
- 6 Device Comparison
- 7 Terminal Configuration and Functions
-
8 Specifications
- 8.1 Absolute Maximum Ratings
- 8.2 ESD Ratings
- 8.3 Recommended Operating Conditions
- 8.4 Active Mode Supply Current Into VCC Excluding External Current
- 8.5 Typical Characteristics – Active Mode Supply Current (Into VCC)
- 8.6 Low-Power Mode Supply Currents (Into VCC) Excluding External Current
- 8.7 Typical Characteristics – LPM4 Current
- 8.8 Schmitt-Trigger Inputs (Ports P1 to P8, RST/NMI, JTAG, XIN, and XT2IN)
- 8.9 Inputs (Ports P1 and P2)
- 8.10 Leakage Current (Ports P1 to P8)
- 8.11 Standard Inputs ( RST/NMI)
- 8.12 Outputs (Ports P1 to P8)
- 8.13 Output Frequency (Ports P1 to P8)
- 8.14 Typical Characteristics – Outputs
- 8.15 POR and Brownout Reset (BOR)
- 8.16 Typical Characteristics – POR and BOR
- 8.17 Supply Voltage Supervisor (SVS), Supply Voltage Monitor (SVM)
- 8.18 Main DCO Characteristics
- 8.19 DCO Frequency
- 8.20 Calibrated DCO Frequencies – Tolerance at Calibration
- 8.21 Calibrated DCO Frequencies – Tolerance Over Temperature 0°C to 85°C
- 8.22 Calibrated DCO Frequencies – Tolerance Over Supply Voltage VCC
- 8.23 Calibrated DCO Frequencies – Overall Tolerance
- 8.24 Typical Characteristics – Calibrated DCO Frequency
- 8.25 Wake-up Times From Lower-Power Modes (LPM3, LPM4)
- 8.26 Typical Characteristics – DCO Clock Wake-up Time From LPM3 or LPM4
- 8.27 DCO With External Resistor ROSC
- 8.28 Typical Characteristics – DCO With External Resistor ROSC
- 8.29 Crystal Oscillator LFXT1, Low-Frequency Mode
- 8.30 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
- 8.31 Crystal Oscillator LFXT1, High-Frequency Mode
- 8.32 Typical Characteristics – LFXT1 Oscillator in HF Mode (XTS = 1)
- 8.33 Crystal Oscillator XT2
- 8.34 Typical Characteristics – XT2 Oscillator
- 8.35 Timer_A
- 8.36 Timer_B
- 8.37 USCI (UART Mode)
- 8.38 USCI (SPI Master Mode)
- 8.39 USCI (SPI Slave Mode)
- 8.40 USCI (I2C Mode)
- 8.41 Comparator_A+
- 8.42 Typical Characteristics – Comparator_A+
- 8.43 12-Bit ADC Power Supply and Input Range Conditions
- 8.44 12-Bit ADC External Reference
- 8.45 12-Bit ADC Built-In Reference
- 8.46 12-Bit ADC Timing Parameters
- 8.47 12-Bit ADC Linearity Parameters
- 8.48 12-Bit ADC Temperature Sensor and Built-In VMID
- 8.49 12-Bit DAC Supply Specifications
- 8.50 12-Bit DAC Linearity Specifications
- 8.51 Typical Characteristics, 12-Bit DAC Linearity Specifications
- 8.52 12-Bit DAC Output Specifications
- 8.53 12-Bit DAC Reference Input Specifications
- 8.54 12-Bit DAC Dynamic Specifications
- 8.55 Flash Memory
- 8.56 RAM
- 8.57 JTAG Interface
- 8.58 JTAG Fuse
-
9 Detailed Description
- 9.1 CPU
- 9.2 Instruction Set
- 9.3 Operating Modes
- 9.4 Interrupt Vector Addresses
- 9.5 Special Function Registers (SFRs)
- 9.6 Memory Organization
- 9.7 Bootloader (BSL)
- 9.8 Flash Memory
- 9.9
Peripherals
- 9.9.1 DMA Controller (MSP430F261x Only)
- 9.9.2 Oscillator and System Clock
- 9.9.3 Calibration Data Stored in Information Memory Segment A
- 9.9.4 Brownout, Supply Voltage Supervisor (SVS)
- 9.9.5 Digital I/O
- 9.9.6 Watchdog Timer (WDT+)
- 9.9.7 Hardware Multiplier
- 9.9.8 Universal Serial Communication Interface (USCI)
- 9.9.9 Timer_A3
- 9.9.10 Timer_B7
- 9.9.11 Comparator_A+
- 9.9.12 ADC12
- 9.9.13 DAC12 (MSP430F261x Only)
- 9.9.14 Peripheral File Map
- 9.10
Port Diagrams
- 9.10.1 Port P1 (P1.0 to P1.7), Input/Output With Schmitt Trigger
- 9.10.2 Port P2 (P2.0 to P2.4, P2.6, and P2.7), Input/Output With Schmitt Trigger
- 9.10.3 Port P2 (P2.5), Input/Output With Schmitt Trigger
- 9.10.4 Port P3 (P3.0 to P3.7), Input/Output With Schmitt Trigger
- 9.10.5 Port P4 (P4.0 to P4.7), Input/Output With Schmitt Trigger
- 9.10.6 Port P5 (P5.0 to P5.7), Input/Output With Schmitt Trigger
- 9.10.7 Port P6 (P6.0 to P6.4), Input/Output With Schmitt Trigger
- 9.10.8 Port P6 (P6.5 and P6.6), Input/Output With Schmitt Trigger
- 9.10.9 Port P6 (P6.7), Input/Output With Schmitt Trigger
- 9.10.10 Port P7 (P7.0 to P7.7), Input/Output With Schmitt Trigger
- 9.10.11 Port P8 (P8.0 to P8.5), Input/Output With Schmitt Trigger
- 9.10.12 Port P8 (P8.6), Input/Output With Schmitt Trigger
- 9.10.13 Port P8 (P8.7), Input/Output With Schmitt Trigger
- 9.10.14 JTAG Pins (TMS, TCK, TDI/TCLK, TDO/TDI) Input/Output With Schmitt Trigger
- 9.10.15 JTAG Fuse Check Mode
- 10Device and Documentation Support
- 11Mechanical, Packaging, and Orderable Information
パッケージ・オプション
メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報
8.52 12-Bit DAC Output Specifications
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | VCC | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|---|
| VO | Output voltage range(1) (see Figure 8-44) | No Load, VeREF+ = AVCC, DAC12_xDAT = 0h, DAC12IR = 1, DAC12AMPx = 7 | 2.2 V, 3 V | 0 | 0.005 | V | |
| No Load, VeREF+ = AVCC, DAC12_xDAT = 0FFFh, DAC12IR = 1, DAC12AMPx = 7 | AVCC – 0.05 | AVCC | |||||
| RLoad = 3 kΩ, VeREF+ = AVCC, DAC12_xDAT = 0h, DAC12IR = 1, DAC12AMPx = 7 | 0 | 0.1 | |||||
| RLoad = 3 kΩ, VeREF+ = AVCC, DAC12_xDAT = 0FFFh, DAC12IR = 1, DAC12AMPx = 7 | AVCC – 0.13 | AVCC | |||||
| CL(DAC12) | Maximum DAC12 load capacitance | 2.2 V, 3 V | 100 | pF | |||
| IL(DAC12) | Maximum DAC12 load current | 2.2 V | –0.5 | 0.5 | mA | ||
| 3 V | –1 | 1 | |||||
| RO/P(DAC12) | Output resistance (see Figure 8-44) | RLoad = 3 kΩ, VO/P(DAC12) = 0 V, DAC12AMPx = 7, DAC12_xDAT = 0h | 2.2 V, 3 V | 150 | 250 | Ω | |
| RLoad = 3 kΩ, VO/P(DAC12) = AVCC, DAC12AMPx = 7, DAC12_xDAT = 0FFFh | 150 | 250 | |||||
| RLoad = 3 kΩ, 0.3 V < VO/P(DAC12) < AVCC – 0.3 V, DAC12AMPx = 7 | 1 | 4 | |||||
(1) Data is valid after the offset calibration of the output amplifier.
Figure 8-44 DAC12_x Output Resistance Tests