JAJSG72F September   2010  – September 2018 MSP430F5304 , MSP430F5308 , MSP430F5309 , MSP430F5310

PRODUCTION DATA.  

  1. 1デバイスの概要
    1. 1.1 特長
    2. 1.2 アプリケーション
    3. 1.3 概要
    4. 1.4 機能ブロック図
  2. 2改訂履歴
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagrams
    2. 4.2 Signal Descriptions
      1. Table 4-1 Signal Descriptions
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Active Mode Supply Current Into VCC Excluding External Current
    5. 5.5  Low-Power Mode Supply Currents (Into VCC) Excluding External Current
    6. 5.6  Thermal Resistance Characteristics
    7. 5.7  Schmitt-Trigger Inputs – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7) (P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3, RST/NMI)
    8. 5.8  Inputs – Ports P1 and P2 (P1.0 to P1.7, P2.0 to P2.7)
    9. 5.9  Leakage Current – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7) (P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3, RST/NMI)
    10. 5.10 Outputs – General-Purpose I/O (Full Drive Strength) (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
    11. 5.11 Outputs – General-Purpose I/O (Reduced Drive Strength) (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
    12. 5.12 Output Frequency – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
    13. 5.13 Typical Characteristics – Outputs, Reduced Drive Strength (PxDS.y = 0)
    14. 5.14 Crystal Oscillator, XT1, Low-Frequency Mode
    15. 5.15 Crystal Oscillator, XT2
    16. 5.16 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
    17. 5.17 Internal Reference, Low-Frequency Oscillator (REFO)
    18. 5.18 DCO Frequency
    19. 5.19 PMM, Brownout Reset (BOR)
    20. 5.20 PMM, Core Voltage
    21. 5.21 PMM, SVS High Side
    22. 5.22 PMM, SVM High Side
    23. 5.23 PMM, SVS Low Side
    24. 5.24 PMM, SVM Low Side
    25. 5.25 Wake-up Times From Low-Power Modes and Reset
    26. 5.26 Timer_A
    27. 5.27 Timer_B
    28. 5.28 USCI (UART Mode) Clock Frequency
    29. 5.29 USCI (UART Mode)
    30. 5.30 USCI (SPI Master Mode) Clock Frequency
    31. 5.31 USCI (SPI Master Mode)
    32. 5.32 USCI (SPI Slave Mode)
    33. 5.33 USCI (I2C Mode)
    34. 5.34 10-Bit ADC, Power Supply and Input Range Conditions
    35. 5.35 10-Bit ADC, Timing Parameters
    36. 5.36 10-Bit ADC, Linearity Parameters
    37. 5.37 REF, External Reference
    38. 5.38 REF, Built-In Reference
    39. 5.39 Comparator_B
    40. 5.40 Ports PU.0 and PU.1
    41. 5.41 LDO-PWR (LDO Power System)
    42. 5.42 Flash Memory
    43. 5.43 JTAG and Spy-Bi-Wire Interface
  6. 6Detailed Description
    1. 6.1  CPU (Link to User's Guide)
    2. 6.2  Operating Modes
    3. 6.3  Interrupt Vector Addresses
    4. 6.4  Memory Organization
    5. 6.5  Bootloader (BSL)
    6. 6.6  JTAG Operation
      1. 6.6.1 JTAG Standard Interface
      2. 6.6.2 Spy-Bi-Wire Interface
    7. 6.7  Flash Memory (Link to User's Guide)
    8. 6.8  RAM (Link to User's Guide)
    9. 6.9  Peripherals
      1. 6.9.1  Digital I/O (Link to User's Guide)
      2. 6.9.2  Port Mapping Controller (Link to User's Guide)
      3. 6.9.3  Oscillator and System Clock (Link to User's Guide)
      4. 6.9.4  Power-Management Module (PMM) (Link to User's Guide)
      5. 6.9.5  Hardware Multiplier (Link to User's Guide)
      6. 6.9.6  Real-Time Clock (RTC_A) (Link to User's Guide)
      7. 6.9.7  Watchdog Timer (WDT_A) (Link to User's Guide)
      8. 6.9.8  System Module (SYS) (Link to User's Guide)
      9. 6.9.9  DMA Controller (Link to User's Guide)
      10. 6.9.10 Universal Serial Communication Interface (USCI) (Links to User's Guide: UART Mode, SPI Mode, I2C Mode)
      11. 6.9.11 TA0 (Link to User's Guide)
      12. 6.9.12 TA1 (Link to User's Guide)
      13. 6.9.13 TA2 (Link to User's Guide)
      14. 6.9.14 TB0 (Link to User's Guide)
      15. 6.9.15 Comparator_B (Link to User's Guide)
      16. 6.9.16 ADC10_A (Link to User's Guide)
      17. 6.9.17 CRC16 (Link to User's Guide)
      18. 6.9.18 Reference (REF) Module Voltage Reference (Link to User's Guide)
      19. 6.9.19 LDO and Port U
      20. 6.9.20 Embedded Emulation Module (EEM) (S Version) (Link to User's Guide)
    10. 6.10 Peripheral File Map
    11. 6.11 Input/Output Diagrams
      1. 6.11.1  Port P1 (P1.0 to P1.7) Input/Output With Schmitt Trigger
      2. 6.11.2  Port P2 (P2.0 to P2.7) Input/Output With Schmitt Trigger
      3. 6.11.3  Port P3 (P3.0 to P3.4) Input/Output With Schmitt Trigger
      4. 6.11.4  Port P4 (P4.0 to P4.7) Input/Output With Schmitt Trigger
      5. 6.11.5  Port P5 (P5.0 and P5.1) Input/Output With Schmitt Trigger
      6. 6.11.6  Port P5 (P5.2) Input/Output With Schmitt Trigger
      7. 6.11.7  Port P5 (P5.3) Input/Output With Schmitt Trigger
      8. 6.11.8  Port P5 (P5.4 and P5.5) Input/Output With Schmitt Trigger
      9. 6.11.9  Port P6 (P6.0 to P6.7) Input/Output With Schmitt Trigger
      10. 6.11.10 Port U (PU.0 and PU.1) Input/Output
      11. 6.11.11 Port J (PJ.0) JTAG Pin TDO, Input/Output With Schmitt Trigger or Output
      12. 6.11.12 Port J (PJ.1 to PJ.3) JTAG Pins TMS, TCK, TDI/TCLK, Input/Output With Schmitt Trigger or Output
    12. 6.12 Device Descriptors
  7. 7デバイスおよびドキュメントのサポート
    1. 7.1 使い始めと次の手順
    2. 7.2 Device Nomenclature
    3. 7.3 ツールとソフトウェア
    4. 7.4 ドキュメントのサポート
    5. 7.5 関連リンク
    6. 7.6 Community Resources
    7. 7.7 商標
    8. 7.8 静電気放電に関する注意事項
    9. 7.9 Glossary
  8. 8メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.10 Peripheral File Map

Table 6-14 lists the register base address for all supported peripherals.

Table 6-14 Peripherals

MODULE NAME BASE ADDRESS OFFSET ADDRESS RANGE
Special Functions (see Table 6-15) 0100h 000h to 01Fh
PMM (see Table 6-16) 0120h 000h to 01Fh
Flash Control (see Table 6-17) 0140h 000h to 00Fh
CRC16 (see Table 6-18) 0150h 000h to 007h
RAM Control (see Table 6-19) 0158h 000h to 001h
Watchdog (see Table 6-20) 015Ch 000h to 001h
UCS (see Table 6-21) 0160h 000h to 01Fh
SYS (see Table 6-22) 0180h 000h to 01Fh
Shared Reference (see Table 6-23) 01B0h 000h to 001h
Port Mapping Control (see Table 6-24) 01C0h 000h to 002h
Port Mapping Port P4 (see Table 6-24) 01E0h 000h to 007h
Port P1, P2 (see Table 6-25) 0200h 000h to 01Fh
Port P3, P4 (see Table 6-26) 0220h 000h to 00Bh
Port P5, P6 (see Table 6-27) 0240h 000h to 00Bh
Port PJ (see Table 6-28) 0320h 000h to 01Fh
TA0 (see Table 6-29) 0340h 000h to 02Eh
TA1 (see Table 6-30) 0380h 000h to 02Eh
TB0 (see Table 6-31) 03C0h 000h to 02Eh
TA2 (see Table 6-32) 0400h 000h to 02Eh
Real-Time Clock (RTC_A) (see Table 6-33) 04A0h 000h to 01Bh
32-Bit Hardware Multiplier (see Table 6-34) 04C0h 000h to 02Fh
DMA General Control (see Table 6-35) 0500h 000h to 00Fh
DMA Channel 0 (see Table 6-35) 0510h 000h to 00Ah
DMA Channel 1 (see Table 6-35) 0520h 000h to 00Ah
DMA Channel 2 (see Table 6-35) 0530h 000h to 00Ah
USCI_A0 (see Table 6-36) 05C0h 000h to 01Fh
USCI_B0 (see Table 6-37) 05E0h 000h to 01Fh
USCI_A1 (see Table 6-38) 0600h 000h to 01Fh
USCI_B1 (see Table 6-39) 0620h 000h to 01Fh
ADC10_A (see Table 6-40) 0740h 000h to 01Fh
Comparator_B (see Table 6-41) 08C0h 000h to 00Fh
LDO-PWR and Port U Configuration
(see Table 6-42)		 0900h 000h to 014h

Table 6-15 Special Function Registers (Base Address: 0100h)

REGISTER DESCRIPTION REGISTER OFFSET
SFR interrupt enable SFRIE1 00h
SFR interrupt flag SFRIFG1 02h
SFR reset pin control SFRRPCR 04h

Table 6-16 PMM Registers (Base Address: 0120h)

REGISTER DESCRIPTION REGISTER OFFSET
PMM control 0 PMMCTL0 00h
PMM control 1 PMMCTL1 02h
SVS high-side control SVSMHCTL 04h
SVS low-side control SVSMLCTL 06h
PMM interrupt flags PMMIFG 0Ch
PMM interrupt enable PMMIE 0Eh
PMM power mode 5 control PM5CTL0 10h

Table 6-17 Flash Control Registers (Base Address: 0140h)

REGISTER DESCRIPTION REGISTER OFFSET
Flash control 1 FCTL1 00h
Flash control 3 FCTL3 04h
Flash control 4 FCTL4 06h

Table 6-18 CRC16 Registers (Base Address: 0150h)

REGISTER DESCRIPTION REGISTER OFFSET
CRC data input CRC16DI 00h
CRC data input reverse byte CRCDIRB 02h
CRC initialization and result CRCINIRES 04h
CRC result reverse byte CRCRESR 06h

Table 6-19 RAM Control Registers (Base Address: 0158h)

REGISTER DESCRIPTION REGISTER OFFSET
RAM control 0 RCCTL0 00h

Table 6-20 Watchdog Registers (Base Address: 015Ch)

REGISTER DESCRIPTION REGISTER OFFSET
Watchdog timer control WDTCTL 00h

Table 6-21 UCS Registers (Base Address: 0160h)

REGISTER DESCRIPTION REGISTER OFFSET
UCS control 0 UCSCTL0 00h
UCS control 1 UCSCTL1 02h
UCS control 2 UCSCTL2 04h
UCS control 3 UCSCTL3 06h
UCS control 4 UCSCTL4 08h
UCS control 5 UCSCTL5 0Ah
UCS control 6 UCSCTL6 0Ch
UCS control 7 UCSCTL7 0Eh
UCS control 8 UCSCTL8 10h

Table 6-22 SYS Registers (Base Address: 0180h)

REGISTER DESCRIPTION REGISTER OFFSET
System control SYSCTL 00h
Bootloader configuration area SYSBSLC 02h
JTAG mailbox control SYSJMBC 06h
JTAG mailbox input 0 SYSJMBI0 08h
JTAG mailbox input 1 SYSJMBI1 0Ah
JTAG mailbox output 0 SYSJMBO0 0Ch
JTAG mailbox output 1 SYSJMBO1 0Eh
Bus error vector generator SYSBERRIV 18h
User NMI vector generator SYSUNIV 1Ah
System NMI vector generator SYSSNIV 1Ch
Reset vector generator SYSRSTIV 1Eh

Table 6-23 Shared Reference Registers (Base Address: 01B0h)

REGISTER DESCRIPTION REGISTER OFFSET
Shared reference control REFCTL 00h

Table 6-24 Port Mapping Registers
(Base Address of Port Mapping Control: 01C0h, Port P4: 01E0h)

REGISTER DESCRIPTION REGISTER OFFSET
Port mapping password PMAPPWD 00h
Port mapping control PMAPCTL 02h
Port P4.0 mapping P4MAP0 00h
Port P4.1 mapping P4MAP1 01h
Port P4.2 mapping P4MAP2 02h
Port P4.3 mapping P4MAP3 03h
Port P4.4 mapping P4MAP4 04h
Port P4.5 mapping P4MAP5 05h
Port P4.6 mapping P4MAP6 06h
Port P4.7 mapping P4MAP7 07h

Table 6-25 Port P1, P2 Registers (Base Address: 0200h)

REGISTER DESCRIPTION REGISTER OFFSET
Port P1 input P1IN 00h
Port P1 output P1OUT 02h
Port P1 direction P1DIR 04h
Port P1 resistor enable P1REN 06h
Port P1 drive strength P1DS 08h
Port P1 selection P1SEL 0Ah
Port P1 interrupt vector word P1IV 0Eh
Port P1 interrupt edge select P1IES 18h
Port P1 interrupt enable P1IE 1Ah
Port P1 interrupt flag P1IFG 1Ch
Port P2 input P2IN 01h
Port P2 output P2OUT 03h
Port P2 direction P2DIR 05h
Port P2 resistor enable P2REN 07h
Port P2 drive strength P2DS 09h
Port P2 selection P2SEL 0Bh
Port P2 interrupt vector word P2IV 1Eh
Port P2 interrupt edge select P2IES 19h
Port P2 interrupt enable P2IE 1Bh
Port P2 interrupt flag P2IFG 1Dh

Table 6-26 Port P3, P4 Registers (Base Address: 0220h)

REGISTER DESCRIPTION REGISTER OFFSET
Port P3 input P3IN 00h
Port P3 output P3OUT 02h
Port P3 direction P3DIR 04h
Port P3 resistor enable P3REN 06h
Port P3 drive strength P3DS 08h
Port P3 selection P3SEL 0Ah
Port P4 input P4IN 01h
Port P4 output P4OUT 03h
Port P4 direction P4DIR 05h
Port P4 resistor enable P4REN 07h
Port P4 drive strength P4DS 09h
Port P4 selection P4SEL 0Bh

Table 6-27 Port P5, P6 Registers (Base Address: 0240h)

REGISTER DESCRIPTION REGISTER OFFSET
Port P5 input P5IN 00h
Port P5 output P5OUT 02h
Port P5 direction P5DIR 04h
Port P5 resistor enable P5REN 06h
Port P5 drive strength P5DS 08h
Port P5 selection P5SEL 0Ah
Port P6 input P6IN 01h
Port P6 output P6OUT 03h
Port P6 direction P6DIR 05h
Port P6 resistor enable P6REN 07h
Port P6 drive strength P6DS 09h
Port P6 selection P6SEL 0Bh

Table 6-28 Port J Registers (Base Address: 0320h)

REGISTER DESCRIPTION REGISTER OFFSET
Port PJ input PJIN 00h
Port PJ output PJOUT 02h
Port PJ direction PJDIR 04h
Port PJ resistor enable PJREN 06h
Port PJ drive strength PJDS 08h

Table 6-29 TA0 Registers (Base Address: 0340h)

REGISTER DESCRIPTION REGISTER OFFSET
TA0 control TA0CTL 00h
Capture/compare control 0 TA0CCTL0 02h
Capture/compare control 1 TA0CCTL1 04h
Capture/compare control 2 TA0CCTL2 06h
Capture/compare control 3 TA0CCTL3 08h
Capture/compare control 4 TA0CCTL4 0Ah
TA0 counter TA0R 10h
Capture/compare 0 TA0CCR0 12h
Capture/compare 1 TA0CCR1 14h
Capture/compare 2 TA0CCR2 16h
Capture/compare 3 TA0CCR3 18h
Capture/compare 4 TA0CCR4 1Ah
TA0 expansion 0 TA0EX0 20h
TA0 interrupt vector TA0IV 2Eh

Table 6-30 TA1 Registers (Base Address: 0380h)

REGISTER DESCRIPTION REGISTER OFFSET
TA1 control TA1CTL 00h
Capture/compare control 0 TA1CCTL0 02h
Capture/compare control 1 TA1CCTL1 04h
Capture/compare control 2 TA1CCTL2 06h
TA1 counter TA1R 10h
Capture/compare 0 TA1CCR0 12h
Capture/compare 1 TA1CCR1 14h
Capture/compare 2 TA1CCR2 16h
TA1 expansion 0 TA1EX0 20h
TA1 interrupt vector TA1IV 2Eh

Table 6-31 TB0 Registers (Base Address: 03C0h)

REGISTER DESCRIPTION REGISTER OFFSET
TB0 control TB0CTL 00h
Capture/compare control 0 TB0CCTL0 02h
Capture/compare control 1 TB0CCTL1 04h
Capture/compare control 2 TB0CCTL2 06h
Capture/compare control 3 TB0CCTL3 08h
Capture/compare control 4 TB0CCTL4 0Ah
Capture/compare control 5 TB0CCTL5 0Ch
Capture/compare control 6 TB0CCTL6 0Eh
TB0 counter TB0R 10h
Capture/compare 0 TB0CCR0 12h
Capture/compare 1 TB0CCR1 14h
Capture/compare 2 TB0CCR2 16h
Capture/compare 3 TB0CCR3 18h
Capture/compare 4 TB0CCR4 1Ah
Capture/compare 5 TB0CCR5 1Ch
Capture/compare 6 TB0CCR6 1Eh
TB0 expansion 0 TB0EX0 20h
TB0 interrupt vector TB0IV 2Eh

Table 6-32 TA2 Registers (Base Address: 0400h)

REGISTER DESCRIPTION REGISTER OFFSET
TA2 control TA2CTL 00h
Capture/compare control 0 TA2CCTL0 02h
Capture/compare control 1 TA2CCTL1 04h
Capture/compare control 2 TA2CCTL2 06h
TA2 counter TA2R 10h
Capture/compare 0 TA2CCR0 12h
Capture/compare 1 TA2CCR1 14h
Capture/compare 2 TA2CCR2 16h
TA2 expansion 0 TA2EX0 20h
TA2 interrupt vector TA2IV 2Eh

Table 6-33 Real-Time Clock Registers (Base Address: 04A0h)

REGISTER DESCRIPTION REGISTER OFFSET
RTC control 0 RTCCTL0 00h
RTC control 1 RTCCTL1 01h
RTC control 2 RTCCTL2 02h
RTC control 3 RTCCTL3 03h
RTC prescaler 0 control RTCPS0CTL 08h
RTC prescaler 1 control RTCPS1CTL 0Ah
RTC prescaler 0 RTCPS0 0Ch
RTC prescaler 1 RTCPS1 0Dh
RTC interrupt vector word RTCIV 0Eh
RTC seconds/counter 1 RTCSEC/RTCNT1 10h
RTC minutes/counter 2 RTCMIN/RTCNT2 11h
RTC hours/counter 3 RTCHOUR/RTCNT3 12h
RTC day of week/counter 4 RTCDOW/RTCNT4 13h
RTC days RTCDAY 14h
RTC month RTCMON 15h
RTC year low RTCYEARL 16h
RTC year high RTCYEARH 17h
RTC alarm minutes RTCAMIN 18h
RTC alarm hours RTCAHOUR 19h
RTC alarm day of week RTCADOW 1Ah
RTC alarm days RTCADAY 1Bh

Table 6-34 32-Bit Hardware Multiplier Registers (Base Address: 04C0h)

REGISTER DESCRIPTION REGISTER OFFSET
16-bit operand 1 – multiply MPY 00h
16-bit operand 1 – signed multiply MPYS 02h
16-bit operand 1 – multiply accumulate MAC 04h
16-bit operand 1 – signed multiply accumulate MACS 06h
16-bit operand 2 OP2 08h
16 × 16 result low word RESLO 0Ah
16 × 16 result high word RESHI 0Ch
16 × 16 sum extension SUMEXT 0Eh
32-bit operand 1 – multiply low word MPY32L 10h
32-bit operand 1 – multiply high word MPY32H 12h
32-bit operand 1 – signed multiply low word MPYS32L 14h
32-bit operand 1 – signed multiply high word MPYS32H 16h
32-bit operand 1 – multiply accumulate low word MAC32L 18h
32-bit operand 1 – multiply accumulate high word MAC32H 1Ah
32-bit operand 1 – signed multiply accumulate low word MACS32L 1Ch
32-bit operand 1 – signed multiply accumulate high word MACS32H 1Eh
32-bit operand 2 – low word OP2L 20h
32-bit operand 2 – high word OP2H 22h
32 × 32 result 0 – least significant word RES0 24h
32 × 32 result 1 RES1 26h
32 × 32 result 2 RES2 28h
32 × 32 result 3 – most significant word RES3 2Ah
MPY32 control 0 MPY32CTL0 2Ch

Table 6-35 DMA Registers (Base Address DMA General Control: 0500h,
DMA Channel 0: 0510h, DMA Channel 1: 0520h, DMA Channel 2: 0530h)

REGISTER DESCRIPTION REGISTER OFFSET
DMA channel 0 control DMA0CTL 00h
DMA channel 0 source address low DMA0SAL 02h
DMA channel 0 source address high DMA0SAH 04h
DMA channel 0 destination address low DMA0DAL 06h
DMA channel 0 destination address high DMA0DAH 08h
DMA channel 0 transfer size DMA0SZ 0Ah
DMA channel 1 control DMA1CTL 00h
DMA channel 1 source address low DMA1SAL 02h
DMA channel 1 source address high DMA1SAH 04h
DMA channel 1 destination address low DMA1DAL 06h
DMA channel 1 destination address high DMA1DAH 08h
DMA channel 1 transfer size DMA1SZ 0Ah
DMA channel 2 control DMA2CTL 00h
DMA channel 2 source address low DMA2SAL 02h
DMA channel 2 source address high DMA2SAH 04h
DMA channel 2 destination address low DMA2DAL 06h
DMA channel 2 destination address high DMA2DAH 08h
DMA channel 2 transfer size DMA2SZ 0Ah
DMA module control 0 DMACTL0 00h
DMA module control 1 DMACTL1 02h
DMA module control 2 DMACTL2 04h
DMA module control 3 DMACTL3 06h
DMA module control 4 DMACTL4 08h
DMA interrupt vector DMAIV 0Ah

Table 6-36 USCI_A0 Registers (Base Address: 05C0h)

REGISTER DESCRIPTION REGISTER OFFSET
USCI control 1 UCA0CTL1 00h
USCI control 0 UCA0CTL0 01h
USCI baud rate 0 UCA0BR0 06h
USCI baud rate 1 UCA0BR1 07h
USCI modulation control UCA0MCTL 08h
USCI status UCA0STAT 0Ah
USCI receive buffer UCA0RXBUF 0Ch
USCI transmit buffer UCA0TXBUF 0Eh
USCI LIN control UCA0ABCTL 10h
USCI IrDA transmit control UCA0IRTCTL 12h
USCI IrDA receive control UCA0IRRCTL 13h
USCI interrupt enable UCA0IE 1Ch
USCI interrupt flags UCA0IFG 1Dh
USCI interrupt vector word UCA0IV 1Eh

Table 6-37 USCI_B0 Registers (Base Address: 05E0h)

REGISTER DESCRIPTION REGISTER OFFSET
USCI synchronous control 1 UCB0CTL1 00h
USCI synchronous control 0 UCB0CTL0 01h
USCI synchronous bit rate 0 UCB0BR0 06h
USCI synchronous bit rate 1 UCB0BR1 07h
USCI synchronous status UCB0STAT 0Ah
USCI synchronous receive buffer UCB0RXBUF 0Ch
USCI synchronous transmit buffer UCB0TXBUF 0Eh
USCI I2C own address UCB0I2COA 10h
USCI I2C slave address UCB0I2CSA 12h
USCI interrupt enable UCB0IE 1Ch
USCI interrupt flags UCB0IFG 1Dh
USCI interrupt vector word UCB0IV 1Eh

Table 6-38 USCI_A1 Registers (Base Address: 0600h)

REGISTER DESCRIPTION REGISTER OFFSET
USCI control 1 UCA1CTL1 00h
USCI control 0 UCA1CTL0 01h
USCI baud rate 0 UCA1BR0 06h
USCI baud rate 1 UCA1BR1 07h
USCI modulation control UCA1MCTL 08h
USCI status UCA1STAT 0Ah
USCI receive buffer UCA1RXBUF 0Ch
USCI transmit buffer UCA1TXBUF 0Eh
USCI LIN control UCA1ABCTL 10h
USCI IrDA transmit control UCA1IRTCTL 12h
USCI IrDA receive control UCA1IRRCTL 13h
USCI interrupt enable UCA1IE 1Ch
USCI interrupt flags UCA1IFG 1Dh
USCI interrupt vector word UCA1IV 1Eh

Table 6-39 USCI_B1 Registers (Base Address: 0620h)

REGISTER DESCRIPTION REGISTER OFFSET
USCI synchronous control 1 UCB1CTL1 00h
USCI synchronous control 0 UCB1CTL0 01h
USCI synchronous bit rate 0 UCB1BR0 06h
USCI synchronous bit rate 1 UCB1BR1 07h
USCI synchronous status UCB1STAT 0Ah
USCI synchronous receive buffer UCB1RXBUF 0Ch
USCI synchronous transmit buffer UCB1TXBUF 0Eh
USCI I2C own address UCB1I2COA 10h
USCI I2C slave address UCB1I2CSA 12h
USCI interrupt enable UCB1IE 1Ch
USCI interrupt flags UCB1IFG 1Dh
USCI interrupt vector word UCB1IV 1Eh

Table 6-40 ADC10_A Registers (Base Address: 0740h)

REGISTER DESCRIPTION REGISTER OFFSET
ADC10_A control 0 ADC10CTL0 00h
ADC10_A control 1 ADC10CTL1 02h
ADC10_A control 2 ADC10CTL2 04h
ADC10_A window comparator low threshold ADC10LO 06h
ADC10_A window comparator high threshold ADC10HI 08h
ADC10_A memory control 0 ADC10MCTL0 0Ah
ADC10_A conversion memory ADC10MEM0 12h
ADC10_A interrupt enable ADC10IE 1Ah
ADC10_A interrupt flags ADC10IGH 1Ch
ADC10_A interrupt vector word ADC10IV 1Eh

Table 6-41 Comparator_B Registers (Base Address: 08C0h)

REGISTER DESCRIPTION REGISTER OFFSET
Comp_B control 0 CBCTL0 00h
Comp_B control 1 CBCTL1 02h
Comp_B control 2 CBCTL2 04h
Comp_B control 3 CBCTL3 06h
Comp_B interrupt CBINT 0Ch
Comp_B interrupt vector word CBIV 0Eh

Table 6-42 LDO and Port U Configuration Registers (Base Address: 0900h)

REGISTER DESCRIPTION REGISTER OFFSET
LDO key/ID LDOKEYPID 00h
PU port control PUCTL 04h
LDO power control LDOPWRCTL 08h