JAJSEA4A September   2017  – December 2017 SN55HVD233-SP

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      概略回路図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Driver Electrical Characteristics
    6. 7.6  Receiver Electrical Characteristics
    7. 7.7  Driver Switching Characteristics
    8. 7.8  Receiver Switching Characteristics
    9. 7.9  Device Switching Characteristics
    10. 7.10 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Modes
      2. 9.3.2 Loopback
      3. 9.3.3 CAN Bus States
      4. 9.3.4 ISO 11898 Compliance of SN55HVD233-SP
        1. 9.3.4.1 Introduction
        2. 9.3.4.2 Differential Signal
          1. 9.3.4.2.1 Common-Mode Signal
        3. 9.3.4.3 Interoperability of 3.3-V CAN in 5-V CAN Systems
      5. 9.3.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Diagnostic Loopback
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Slope Control
        2. 10.2.2.2 Standby
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Bus Loading, Length, and Number of Nodes
      2. 12.1.2 CAN Termination
    2. 12.2 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 ドキュメントの更新通知を受け取る方法
    2. 13.2 コミュニティ・リソース
    3. 13.3 商標
    4. 13.4 静電気放電に関する注意事項
    5. 13.5 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.9 Device Switching Characteristics

The specifications shown below are valid across temperature range of –55°C to 125°C pre-radiation and 25°C post-radiation. When different, the post-radiation values are shown in a separate row specified by the corresponding RHA level (L = 50 krad).
PARAMETERTEST CONDITIONSSUBGROUP(2)MINTYP(1)MAXUNIT
t(LBK) Loopback delay, driver input to receiver output See Figure 22 7.5 ns
t(loop1) Total loop delay, driver input to receiver output, recessive to dominant V(RS) at 0 V, see Figure 21 [9, 10, 11] 70 150 ns
V(RS) with 10 kΩ to ground, see Figure 21 [9, 10, 11] 105 225
V(RS) with 50 kΩ to ground, see Figure 21 [9, 10, 11] 500 600
t(loop2) Total loop delay, driver input to receiver output, dominant to recessive V(RS) at 0 V, See Figure 21 [9, 10, 11] 70 150 ns
V(RS) with 10 kΩ to ground, see Figure 21 [9, 10, 11] 105 225
V(RS) with 50 kΩ to ground, see Figure 21 [9, 10, 11] 500 600
(1) All typical values are at 25°C and with a 3.3-V supply.
(2) For subgroup definitions, please see Table 1.

Table 1. Quality Conformance Inspection(1)

SUBGROUPDESCRIPTIONTEMPERATURE (°C)
1 Static tests at 25
2 Static tests at 125
3 Static tests at –55
4 Dynamic tests at 25
5 Dynamic tests at 125
6 Dynamic tests at –55
7 Functional tests at 25
8A Functional tests at 125
8B Functional tests at –55
9 Switching tests at 25
10 Switching tests at 125
11 Switching tests at –55
(1) MIL-STD-883, Method 5005 - Group A