JAJSKL8E june   2006  – october 2020 SN65LVDS302

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Input Electrical Characteristics
    7. 6.7  Output Electrical Characteristics
    8. 6.8  Timing Requirements
    9. 6.9  Switching Characteristics
    10. 6.10 Device Power Dissipation
    11.     Typical Characteristics
  8. 7 Parameter Measurement Information
    1.     20
    2. 7.1 Power Consumption Tests
    3. 7.2 Typical IC Power Consumption Test Pattern
    4. 7.3 Maximum Power Consumption Test Pattern
    5. 7.4 Output Skew Pulse Position and Jitter Performance
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Swap Pin Functionality
      2. 8.3.2 Parity Error Detection and Handling
    4. 8.4 Device Functional Modes
      1. 8.4.1 Deserialization Modes
        1. 8.4.1.1 1-Channel Mode
        2. 8.4.1.2 2-Channel Mode
        3. 8.4.1.3 3-Channel Mode
      2. 8.4.2 Powerdown Modes
        1. 8.4.2.1 Shutdown Mode
        2. 8.4.2.2 Standby Mode
      3. 8.4.3 Active Modes
        1. 8.4.3.1 Acquire Mode (PLL Approaches Lock)
        2. 8.4.3.2 Receive Mode
      4. 8.4.4 Status Detect and Operating Modes Flow
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Application Information
      2. 9.1.2 Preventing Increased Leakage Currents in Control Inputs
      3. 9.1.3 Calculation Example: HVGA Display
      4. 9.1.4 How to Determine Interconnect Skew and Jitter Budget
      5. 9.1.5 F/S Pin Setting and Connecting the SN65LVDS302 to an LCD Driver
      6. 9.1.6 How to Determine the LCD Driver Timing Margin
      7. 9.1.7 Typical Application Frequencies
    2. 9.2 Typical Applications
      1. 9.2.1 VGA Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Power-Up and Power-Down Sequences
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Dual LCD-Display Application
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Application Curve
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
  13. 12Device and Documentation Support
    1. 12.1 Community Resource
    2. 12.2 Trademarks
  14. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

11.1 Layout Guidelines

Use chamfered corners (45° bends) instead of right-angle (90°) bends. Right-angle bends increase the effective trace width, which changes the differential trace impedance creating large discontinuities. A 45° bend is seen as a smaller discontinuity.

When routing traces next to a via or between an array of vias, make sure that the via clearance section does not interrupt the path of the return current on the ground plane below.

Avoid metal layers and traces underneath or between the pads of the LVDS connectors for better impedance matching. Otherwise they cause the differential impedance to drop below 75 Ω and fail the board during TDR testing.

Use solid power and ground planes for 100 Ω impedance control and minimum power noise.

For a multilayer PCB, TI recommends keeping one common GND layer underneath the device and connect all ground terminals directly to this plane. For 100 Ω differential impedance, use the smallest trace spacing possible, which is usually specified by the PCB vendor.

Keep the trace length as short as possible to minimize attenuation.

Place bulk capacitors (10 μF) close to power sources, such as voltage regulators or where the power is supplied to the PCB.