JAJSM92 データシート

JAJSM92D October 2003 – September 2021 SN74CB3Q3305

PRODUCTION DATA

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）

DCU|8
PW|8

サーマルパッド・メカニカル・データ

発注情報

6.5 Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)⁽¹⁾

PARAMETER		TEST CONDITIONS			TYP⁽²⁾	MAX	UNIT
V_IK		V_CC = 3.6 V,	I_I = –18 mA			–1.8	V
I_IN	Control inputs	V_CC = 3.6 V,	V_IN = 0 to 5.5 V			±1	µA
I_OZ⁽³⁾		V_CC = 3.6 V,	V_O = 0 to 5.5 V, V_I = 0,	Switch OFF, V_IN = V_CC or GND		±1	µA
I_off		V_CC = 0,	V_O = 0 to 5.5 V,	V_I = 0		1	µA
I_CC		V_CC = 3.6 V,	I_I/O = 0, Switch ON or OFF,	V_IN = V_CC or GND	0.25	0.7	mA
ΔI_CC⁽⁴⁾	Control inputs	V_CC = 3.6 V, One input at 3 V, Other inputs at V_CC or GND				25	µA
I_CCD⁽⁵⁾	Per control input	V_CC = 3.6 V,	A and B ports open,		0.040	0.045	mA/ MHz
I_CCD⁽⁵⁾	Per control input	Control input switching at 50% duty cycle			0.040	0.045	mA/ MHz
C_in	Control inputs	V_CC = 3.3 V,	V_IN = 5.5 V, 3.3 V, or 0		2.5	3.5	pF
C_io(OFF)		V_CC = 3.3 V,	Switch OFF, V_IN = V_CC or GND,	V_I/O = 5.5 V, 3.3 V, or 0	3.5	5	pF
C_io(ON)		V_CC = 3.3 V,	Switch ON, V_IN = V_CC or GND,	V_I/O = 5.5 V, 3.3 V, or 0	8	10.5	pF
r_on⁽⁶⁾		V_CC = 2.3 V, TYP at V_CC = 2.5 V	V_I = 0, I_O = 30 mA		3	8	Ω
		V_CC = 2.3 V, TYP at V_CC = 2.5 V	V_I = 1.7 V, I_O = –15 mA		3.5	9
		V_CC = 3 V	V_I = 0, I_O = 30 mA		3	6
		V_CC = 3 V	V_I = 2.4 V, I_O = –15 mA		3.5	8

(1) V_IN and I_IN refer to control inputs. V_I, V_O, I_I, and I_O refer to data pins.

(2) All typical values are at V_CC = 3.3 V (unless otherwise noted), T_A = 25°C.

(3) For I/O ports, the parameter I_OZ includes the input leakage current.

(4) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V_CC or GND.

(5) This parameter specifies the dynamic power-supply current associated with the operating frequency of a single control input (see Figure 9-2).

(6) Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals.