JAJSP93C June   1984  – October 2022 SN75176A

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Recommended Operating Conditions
    3. 6.3 Thermal Information
    4. 6.4 Dissipation Rating Table
    5. 6.5 Electrical Characteristics – Driver
    6. 6.6 Electrical Characteristics – Receiver
    7. 6.7 Switching Characteristics – Driver
    8. 6.8 Switching Characteristics – Receiver
    9. 6.9 Typical Characteristics
  7. 7 Parameter Measurement Information
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Driver
      2. 8.3.2 Receiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Device Powered
      2. 8.4.2 Device Unpowered
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Trademarks
    2. 10.2 Electrostatic Discharge Caution
    3. 10.3 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • D|8
  • P|8
サーマルパッド・メカニカル・データ
発注情報

6.5 Electrical Characteristics – Driver

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
VIK Input clamp voltage II = –18 mA –1.5 V
VOH High-level output voltage VIH = 2 V, VIL = 0.8 V, IOH = –33 mA 3.7 V
VOL Low-level output voltage VIH = 2 V, VIL = 0.8 V, IOH = 33 mA 1.1 V
|VOD1| Differential output voltage IO = 0 2VOD2 V
|VOD2| Differential output voltage RL = 100 Ω, see Figure 7-1 2 2.7 V
RL = 54 Ω, see Figure 7-1 1.5 2.4
Δ|VOD| Change in magnitude of differential output voltage(2) ±0.2 V
VOC Common-mode output voltage(3) RL = 54 Ω or 100 Ω, see Figure 7-1 3 V
Δ|VOC| Change in magnitude of common-mode output voltage(2) ±0.2 V
IO Output current Output disabled(4) VO = 12 V 1 mA
VO = –7 V –0.8
IIH High-level input current VI = 2.4 V 20 µA
IIL Low-level input current VI = 0.4 V –400 µA
IOS Short-circuit output current VO = –7 V –250 mA
VO = VCC 250
VO = 12 V 500
ICC Supply current (total package) No load Outputs enabled 35 50 mA
Outputs disabled 26 40
(1) All typical values are at VCC = 5 V and TA = 25°C.
(2) Δ|VOD| and D|VOC| are the changes in magnitude of VOD and VOC respectively, that occur when the input is changed from a high level to a low level.
(3) In ANSI Standard EIA/TIA-422-B, VOC, which is the average of the two output voltages with respect to GND, is called output offset voltage, VOS.
(4) This applies for both power on and off; refer to ANSI Standard EIA/TIA-422-B for exact conditions.