JAJSSI1 December   2023 TAS5827

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
      1. 5.7.1 Bridge Tied Load (BTL) Configuration Curves with BD Modulation
      2. 5.7.2 Bridge Tied Load (BTL) Configuration Curves with 1SPW Modulation
      3. 5.7.3 Parallel Bridge Tied Load (PBTL) Configuration With BD Modulation
      4. 5.7.4 Parallel Bridge Tied Load (PBTL) Configuration With 1SPW Modulation
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Power Supplies
      2. 6.3.2 Device Clocking
      3. 6.3.3 Serial Audio Port – Clock Rates
      4. 6.3.4 Clock Halt Auto-recovery
      5. 6.3.5 Sample Rate on the Fly Change
      6. 6.3.6 Serial Audio Port - Data Formats and Bit Depths
    4. 6.4 Device Functional Modes
      1. 6.4.1 Software Control
      2. 6.4.2 Speaker Amplifier Operating Modes
        1. 6.4.2.1 BTL Mode
        2. 6.4.2.2 PBTL Mode
      3. 6.4.3 Low EMI Modes
        1. 6.4.3.1 Spread Spectrum
        2. 6.4.3.2 Channel to Channel Phase Shift
        3. 6.4.3.3 Multi-Devices PWM Phase Synchronization
          1. 6.4.3.3.1 Phase Synchronization With I2S Clock In Startup Phase
          2. 6.4.3.3.2 Phase Synchronization With GPIO
      4. 6.4.4 Thermal Foldback
      5. 6.4.5 Device State Control
      6. 6.4.6 Device Modulation
        1. 6.4.6.1 BD Modulation
        2. 6.4.6.2 1SPW Modulation
        3. 6.4.6.3 Hybrid Modulation
      7. 6.4.7 Programming and Control
        1. 6.4.7.1 I2C Serial Communication Bus
        2. 6.4.7.2 Hardware Control Mode
        3. 6.4.7.3 I2C Target Address
          1. 6.4.7.3.1 Random Write
          2. 6.4.7.3.2 Sequential Write
          3. 6.4.7.3.3 Random Read
          4. 6.4.7.3.4 Sequential Read
          5. 6.4.7.3.5 DSP Memory Book, Page and BQ update
          6. 6.4.7.3.6 Checksum
            1. 6.4.7.3.6.1 Cyclic Redundancy Check (CRC) Checksum
            2. 6.4.7.3.6.2 Exclusive or (XOR) Checksum
        4. 6.4.7.4 Control via Software
          1. 6.4.7.4.1 Startup Procedures
          2. 6.4.7.4.2 Shutdown Procedures
        5. 6.4.7.5 Protection and Monitoring
          1. 6.4.7.5.1 Overcurrent Limit (Cycle-By-Cycle)
          2. 6.4.7.5.2 Overcurrent Shutdown (OCSD)
          3. 6.4.7.5.3 DC Detect Error
          4. 6.4.7.5.4 Overtemperature Shutdown (OTSD)
          5. 6.4.7.5.5 PVDD Overvoltage and Undervoltage Error
          6. 6.4.7.5.6 PVDD Drop Detection
          7. 6.4.7.5.7 Clock Fault
    5. 6.5 Register Maps
      1. 6.5.1 reg_map Registers
  8. 7 Application and Implementation
    1. 7.1 Typical Applications
      1. 7.1.1 2.0 (Stereo BTL) System
      2. 7.1.2 Mono (PBTL) Systems
      3. 7.1.3 Layout Guidelines
        1. 7.1.3.1 General Guidelines for Audio Amplifiers
        2. 7.1.3.2 Importance of PVDD Bypass Capacitor Placement on PVDD Network
        3. 7.1.3.3 Optimizing Thermal Performance
          1. 7.1.3.3.1 Device, Copper, and Component Layout
          2. 7.1.3.3.2 Stencil Pattern
          3. 7.1.3.3.3 PCB footprint and Via Arrangement
          4. 7.1.3.3.4 Solder Stencil
        4. 7.1.3.4 Layout Example
  9. 8 Power Supply Recommendations
    1. 8.1 DVDD Supply
    2. 8.2 PVDD Supply
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Device Nomenclature
      2. 9.1.2 Development Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.4.2.2 PBTL Mode

The PBTL mode of operation is used to describe an operation in which the two outputs of the device are placed in parallel with one another to increase the power-sourcing capabilities of the device. On the output side of the TAS5827 device, the summation of the devices can be done before the filter in a configuration called Pre-Filter Parallel Bridge Tied Load (PBTL). However, the two outputs can be required to merge together after the inductor portion of the output filter. Doing so does require two additional inductors, but allows smaller, less expensive inductors to be used because the current is divided between the two inductors. The process is called Post-Filter PBTL. On the input side of the TAS5827 device, the input signal to the PBTL amplifier is the left frame of I2S or TDM data.