SNLS766 July   2024 TDP20MB421

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 DC Electrical Characteristics
    6. 5.6 High-Speed Electrical Characteristics
    7. 5.7 SMBUS/I2C Timing Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 5-Level Control Inputs
      2. 6.3.2 Linear Equalization
      3. 6.3.3 Flat Gain
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active Mode
      2. 6.4.2 Standby Mode
    5. 6.5 Programming
      1. 6.5.1 Pin Mode
      2. 6.5.2 SMBUS/I2C Register Control Interface
        1. 6.5.2.1 Shared Registers
        2. 6.5.2.2 Channel Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 DP 2.1 Mainlink Signal Conditioning
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
        3. 7.2.1.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

4 Pin Configuration and Functions

TDP20MB421 RUA Package, 42-Pin WQFN (Top View)Figure 4-1 RUA Package, 42-Pin WQFN (Top View)
Table 4-1 Pin Functions
PINTYPE(1)DESCRIPTION
NAMENO.
MODE41I, 5-levelSets device control configuration modes. The 5-level IO pin is defined in Table 6-1. The pin is used at device power up or in normal operation mode.
L0: Pin Mode – device control configuration is done solely by strap pins.
L1 or L2: SMBus/I2C Mode – device control configuration is done by an external controller with SMBus/I2C primary. This pin along with ADDR pin set the secondary address of the device.
L3 and L4 (Float): RESERVED – TI internal test modes.
EQ0 /ADDR40I, 5-levelIn Pin Mode:
The EQ0 and EQ1 pins sets receiver linear equalization CTLE (AC gain) for all channels according to Table 6-2. These pins are sampled at device power up only.
In SMBus/I2C Mode:
The ADDR pin in conjunction with the MODE pin sets SMBus / I2C secondary address according to Table 6-4. The pin is sampled at device power-up only.
EQ120I, 5-level
GAIN /SDA1I, 5-level / IOIn Pin Mode:
Flat gain (broadband gain – DC and AC) from the input to the output of the device for all channels. The device also provides AC (high frequency) gain in the form of equalization controlled by EQ pins or SMBus/I2C registers. The pin is sampled at device power up only.
In SMBus/I2C Mode:
3.3V SMBus/I2C data. External pullup resistor such as 4.7 kΩ required for operation.
GNDEP, 2, 6, 9, 12, 16, 21, 30, 39PGround reference for the device.
EP: the Exposed Pad at the bottom of the QFN package. The EP is used as the GND return for the device. Connect the EP to one or more ground planes through the low resistance path. A via array provides a low impedance path to GND. The EP also improves thermal dissipation.
PD18I, 3.3V LVCMOS2-level logic controlling the operating state of the redriver. Active in both Pin Mode and SMBus/I2C Mode. The pin has a weak 1MkΩ internal pulldown resistor.
High: power down for all channels
Low: power up, normal operation for all channels
TEST /SCL42I, 5-level / IOIn Pin Mode:
TI Test mode. Use external 1kΩ pulldown resistor instead.
In SMBus/I2C Mode:
3.3V SMBus/I2C clock. External pullup resistor such as 4.7kΩ required for operation.
RXA3P37IInverting differential RX input – Port A, Channel 3.
RXA3N38INoninverting differential RX input – Port A, Channel 3.
RXA2P33IInverting differential RX input – Port A, Channel 2.
RXA2N34INoninverting differential RX input – Port A, Channel 2.
RXA1P28IInverting differential RX input – Port A, Channel 1.
RXA1N29INoninverting differential RX input – Port A, Channel 1.
RXA0P24IInverting differential RX input – Port A, Channel 0.
RXA0N25INoninverting differential RX input – Port A, Channel 0.
RXB3P35IInverting differential RX input – Port B, Channel 3.
RXB3N36INoninverting differential RX input – Port B, Channel 3.
RXB2P31IInverting differential RX input – Port B, Channel 2.
RXB2N32INoninverting differential RX input – Port B, Channel 2.
RXB1P26IInverting differential RX input – Port B, Channel 1.
RXB1N27INoninverting differential RX input – Port B, Channel 1.
RXB0P22IInverting differential RX input – Port B, Channel 0.
RXB0N23INoninverting differential RX input – Port B, Channel 0.
SEL17I, 3.3V LVCMOSSelects the mux path. Active in both Pin Mode and SMBus/I2C Mode. The pin has a weak internal pulldown resistor. Exercise the SEL pin in system implementations for mux selection between Port A vs Port B.
L: Port A selected.
H: Port B selected.
TX3P4OInverting differential TX output, Channel 3.
TX3N3ONoninverting differential TX output, Channel 3.
TX2P8OInverting differential TX output, Channel 2.
TX2N7ONoninverting differential TX output, Channel 2.
TX1P11OInverting differential TX output, Channel 1.
TX1N10ONoninverting differential TX output, Channel 1.
TX0P15OInverting differential TX output, Channel 0.
TX0N14ONoninverting differential TX output, Channel 0.
RSVD319OTI internal test pin. Keep no connect.
VCC5, 13PPower supply, VCC = 3.3V ± 10%. Connect the VCC pins on this device through a low-resistance path to the board VCC plane.
(1) I = input, O = output, P = power, GND = ground