JAJST56D October   2001  – February 2024 TFP410

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 T.M.D.S. Pixel Data and Control Signal Encoding
      2. 6.3.2 Universal Graphics Controller Interface Voltage Signal Levels
      3. 6.3.3 Universal Graphics Controller Interface Clock Inputs
    4. 6.4 Device Functional Modes
      1. 6.4.1 Universal Graphics Controller Interface Modes
      2. 6.4.2 Data De-skew Feature
      3. 6.4.3 Hot Plug/Unplug (Auto Connect/Disconnect Detection)
      4. 6.4.4 Device Configuration and I2C RESET Description
      5. 6.4.5 DE Generator
    5. 6.5 Programming
      1. 6.5.1 I2C Interface
    6. 6.6 Register Maps
      1. 6.6.1  VEN_ID Register (Sub-Address = 01−00 ) [reset = 0x014C]
      2. 6.6.2  DEV_ID Register (Sub-Address = 03–02) [reset = 0x0410]
      3. 6.6.3  REV_ID Register (Sub-Address = 04) [reset = 0x00]
      4. 6.6.4  Reserved Register (Sub-Address = 07–05) [reset = 0x641400]
      5. 6.6.5  CTL_1_MODE (Sub-Address = 08) [reset = 0xBE]
      6. 6.6.6  CTL_2_MODE Register (Sub-Address = 09) [reset = 0x00]
      7. 6.6.7  CTL_3_MODE Register (Sub-Address = 0A) [reset = 0x80]
      8. 6.6.8  CFG Register (Sub-Address = 0B)
      9. 6.6.9  RESERVED Register (Sub-Address = 0E–0C) [reset = 0x97D0A9]
      10. 6.6.10 DE_DLY Register (Sub-Address = 32) [reset = 0x00]
      11. 6.6.11 DE_CTL Register (Sub-Address = 33) [reset = 0x00]
      12. 6.6.12 DE_TOP Register (Sub-Address = 34) [reset = 0x00]
      13. 6.6.13 DE_CNT Register (Sub-Address = 37–36) [reset = 0x0000]
      14. 6.6.14 DE_LIN Register (Sub-Address = 39–38) [reset = 0x0000]
      15. 6.6.15 H_RES Register (Sub-Address = 3B−3A)
      16. 6.6.16 V_RES Register (Sub-Address = 3D−3C)
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Data and Control Signals
        2. 7.2.2.2 Configuration Options
        3. 7.2.2.3 Power Supplies Decoupling
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
      1. 7.3.1 DVDD
      2. 7.3.2 TVDD
      3. 7.3.3 PVDD
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 Layer Stack
        2. 7.4.1.2 Routing High-Speed Differential Signal Traces (RxC-, RxC+, Rx0-, Rx0+, Rx1-, Rx1+, Rx2-, Rx2+)
        3. 7.4.1.3 DVI Connector
      2. 7.4.2 Layout Example
      3. 7.4.3 TI PowerPAD 64-Pin HTQFP Package
  9. 8 Device and Documentation Support
    1. 8.1 ドキュメントの更新通知を受け取る方法
    2. 8.2 サポート・リソース
    3. 8.3 Trademarks
    4. 8.4 静電気放電に関する注意事項
    5. 8.5 用語集
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • PAP|64
サーマルパッド・メカニカル・データ
発注情報

7.4.1.1 Layer Stack

The pinout of Texas Instruments' High Speed Interface (HSI) devices features differential signal pairs and the remaining signals comprise the supply rails, VCC and ground, and lower-speed signals, such as control pins. As an example, consider a device X which is a repeater/re-driver, so both inputs and outputs are high-speed differential signals. These guidelines can be applied to other high-speed devices such as drivers, receivers, multiplexers, and so on.

A minimum of four layers is required to accomplish a low-EMI PCB design. Layer stacking should be in the following order (top-to-bottom): high-speed differential signal layer, ground plane, power plane and control signal layer.

GUID-4F77838C-06F8-471B-9D99-316638ACF595-low.pngFigure 7-6 PCB Stack Up