JAJSNM5A December   2021  – August 2022 TMP9R00-SP

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Two-Wire Timing Requirements
      1. 6.6.1 Timing Diagrams
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Temperature Measurement Data
      2. 7.3.2 Series Resistance Cancellation
      3. 7.3.3 Differential Input Capacitance
      4. 7.3.4 Sensor Fault
      5. 7.3.5 THERM Functions
    4. 7.4 Device Functional Modes
      1. 7.4.1 Shutdown Mode (SD)
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
        1. 7.5.1.1 Bus Overview
        2. 7.5.1.2 Bus Definitions
        3. 7.5.1.3 Serial Bus Address
        4. 7.5.1.4 Read and Write Operations
          1. 7.5.1.4.1 Single Register Reads
          2. 7.5.1.4.2 Block Register Reads
        5. 7.5.1.5 Timeout Function
        6. 7.5.1.6 High-Speed Mode
      2. 7.5.2 TMP9R00-SP Register Reset
      3. 7.5.3 Lock Register
    6. 7.6 Register Maps
      1. 7.6.1 Register Information
        1. 7.6.1.1  Pointer Register
        2. 7.6.1.2  Local and Remote Temperature Value Registers
        3. 7.6.1.3  Software Reset Register
        4. 7.6.1.4  THERM Status Register
        5. 7.6.1.5  THERM2 Status Register
        6. 7.6.1.6  Remote Channel Open Status Register
        7. 7.6.1.7  Configuration Register
        8. 7.6.1.8  η-Factor Correction Register
        9. 7.6.1.9  Remote Temperature Offset Register
        10. 7.6.1.10 THERM Hysteresis Register
        11. 7.6.1.11 Local and Remote THERM and THERM2 Limit Registers
        12. 7.6.1.12 Block Read - Auto Increment Pointer
        13. 7.6.1.13 Lock Register
        14. 7.6.1.14 Manufacturer and Device Identification Plus Revision Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 サポート・リソース
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  10. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

5 Pin Configuration and Functions

Figure 5-1 TMP9R00-SP HKT Package 16-Pin CFP Top View
Table 5-1 Pin Functions
PIN I/O DESCRIPTION
NAME NO.
D4+ 1 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D3+ 2 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D2+ 3 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D1+ 4 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D- 5 Analog input Negative connection to remote temperature sensors. Common for 8 remote channels.
GND 6 Ground Supply ground connection
ADD 7 Digital input Address select. Connect to GND, V+, SDA, or SCL.
THERM 8 Digital output Thermal shutdown or fan-control pin.
Active low; open-drain; requires a pullup resistor to a voltage between 1.7 V and 3.6 V, not necessarily V+. If this pin is not used it may be left open or grounded.
THERM2 9 Digital output Second THERM output.
Active low; open-drain; requires a pullup resistor to a voltage between 1.7 V and 3.6V, not necessarily V+. If this pin is not used it may be left open or grounded.
SDA 10 Bidirectional digital input/output Serial data line for I2C or SMBus compatible two-wire interface. Open-drain; requires a pullup resistor to a voltage between 1.7 V and 3.6V, not necessarily V+.
SCL 11 Digital input Serial clock line for I2C- or SMBus compatible two-wire interface.
Requires a pullup resistor to a voltage between 1.7 V and 3.6V (not necessarily V+) if driven by an open-drain output.
V+ 12 Power Supply Positive supply voltage, 1.7 V to 2.0V; requires 0.1-µF bypass capacitor to ground.
D8+ 13 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D7+ 14 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D6+ 15 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.
D5+ 16 Analog input Positive connection to remote temperature sensors. A total of 8 remote channels are supported. An unused channel must be connected to D–.