JAJSFZ4E March   2009  – August 2018 TMS320C28341 , TMS320C28342 , TMS320C28343 , TMS320C28344 , TMS320C28345 , TMS320C28346

PRODUCTION DATA.  

  1. 1デバイスの概要
    1. 1.1 特長
    2. 1.2 アプリケーション
    3. 1.3 概要
    4. 1.4 機能ブロック図
  2. 2改訂履歴
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagrams
    2. 4.2 Signal Descriptions
  5. 5Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings – Automotive
    3. 5.3 ESD Ratings – Commercial
    4. 5.4 Recommended Operating Conditions
    5. 5.5 Power Consumption Summary
      1. Table 5-1 TMS320C28346/C28344 Current Consumption by Power-Supply Pins at 300-MHz SYSCLKOUT
      2. Table 5-2 TMS320C28345/C28343 Current Consumption by Power-Supply Pins at 200-MHz SYSCLKOUT
      3. 5.5.1     Reducing Current Consumption
    6. 5.6 Electrical Characteristics
    7. 5.7 Thermal Resistance Characteristics
      1. 5.7.1 ZHH Package
      2. 5.7.2 ZFE Package
    8. 5.8 Thermal Design Considerations
    9. 5.9 Timing and Switching Characteristics
      1. 5.9.1 Timing Parameter Symbology
        1. 5.9.1.1 General Notes on Timing Parameters
        2. 5.9.1.2 Test Load Circuit
        3. 5.9.1.3 Device Clock Table
          1. Table 5-4 Clocking and Nomenclature (300-MHz Devices)
          2. Table 5-5 Clocking and Nomenclature (200-MHz Devices)
      2. 5.9.2 Power Sequencing
        1. 5.9.2.1   Power Management and Supervisory Circuit Solutions
        2. Table 5-6 Reset (XRS) Timing Requirements
      3. 5.9.3 Clock Requirements and Characteristics
        1. Table 5-7 XCLKIN/X1 Timing Requirements – PLL Enabled
        2. Table 5-8 XCLKIN/X1 Timing Requirements – PLL Disabled
        3. Table 5-9 XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
      4. 5.9.4 Peripherals
        1. 5.9.4.1 General-Purpose Input/Output (GPIO)
          1. 5.9.4.1.1 GPIO - Output Timing
            1. Table 5-10 General-Purpose Output Switching Characteristics
          2. 5.9.4.1.2 GPIO - Input Timing
            1. Table 5-11 General-Purpose Input Timing Requirements
          3. 5.9.4.1.3 Sampling Window Width for Input Signals
          4. 5.9.4.1.4 Low-Power Mode Wakeup Timing
            1. Table 5-12 IDLE Mode Timing Requirements
            2. Table 5-13 IDLE Mode Switching Characteristics
            3. Table 5-14 STANDBY Mode Timing Requirements
            4. Table 5-15 STANDBY Mode Switching Characteristics
            5. Table 5-16 HALT Mode Timing Requirements
            6. Table 5-17 HALT Mode Switching Characteristics
        2. 5.9.4.2 Enhanced Control Peripherals
          1. 5.9.4.2.1 Enhanced Pulse Width Modulator (ePWM) Timing
            1. Table 5-18 ePWM Timing Requirements
            2. Table 5-19 ePWM Switching Characteristics
          2. 5.9.4.2.2 Trip-Zone Input Timing
            1. Table 5-20 Trip-Zone Input Timing Requirements
          3. 5.9.4.2.3 High-Resolution PWM Timing
            1. Table 5-21 High-Resolution PWM Characteristics at SYSCLKOUT = (150–300 MHz)
          4. 5.9.4.2.4 Enhanced Capture (eCAP) Timing
            1. Table 5-22 Enhanced Capture (eCAP) Timing Requirements
            2. Table 5-23 eCAP Switching Characteristics
          5. 5.9.4.2.5 Enhanced Quadrature Encoder Pulse (eQEP) Timing
            1. Table 5-24 Enhanced Quadrature Encoder Pulse (eQEP) Timing Requirements
            2. Table 5-25 eQEP Switching Characteristics
          6. 5.9.4.2.6 ADC Start-of-Conversion Timing
            1. Table 5-26 External ADC Start-of-Conversion Switching Characteristics
        3. 5.9.4.3 External Interrupt Timing
          1. Table 5-27 External Interrupt Timing Requirements
          2. Table 5-28 External Interrupt Switching Characteristics
        4. 5.9.4.4 I2C Electrical Specification and Timing
          1. Table 5-29 I2C Timing
        5. 5.9.4.5 Serial Peripheral Interface (SPI) Timing
          1. 5.9.4.5.1 Master Mode Timing
            1. Table 5-30 SPI Master Mode External Timing (Clock Phase = 0)
            2. Table 5-31 SPI Master Mode External Timing (Clock Phase = 1)
          2. 5.9.4.5.2 Slave Mode Timing
            1. Table 5-32 SPI Slave Mode External Timing (Clock Phase = 0)
            2. Table 5-33 SPI Slave Mode External Timing (Clock Phase = 1)
        6. 5.9.4.6 Multichannel Buffered Serial Port (McBSP) Timing
          1. 5.9.4.6.1 McBSP Transmit and Receive Timing
            1. Table 5-34 McBSP Timing Requirements
            2. Table 5-35 McBSP Switching Characteristics
          2. 5.9.4.6.2 McBSP as SPI Master or Slave Timing
            1. Table 5-36 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0)
            2. Table 5-37 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)
            3. Table 5-38 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0)
            4. Table 5-39 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)
            5. Table 5-40 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)
            6. Table 5-41 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)
            7. Table 5-42 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1)
            8. Table 5-43 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)
      5. 5.9.5 Emulator Connection Without Signal Buffering for the MCU
      6. 5.9.6 External Interface (XINTF) Timing
        1. 5.9.6.1 USEREADY = 0
        2. 5.9.6.2 Synchronous Mode (USEREADY = 1, READYMODE = 0)
        3. 5.9.6.3 Asynchronous Mode (USEREADY = 1, READYMODE = 1)
        4. 5.9.6.4 XINTF Signal Alignment to XCLKOUT
        5. 5.9.6.5 External Interface Read Timing
          1. Table 5-46 External Interface Read Timing Requirements
          2. Table 5-47 External Interface Read Switching Characteristics
        6. 5.9.6.6 External Interface Write Timing
          1. Table 5-48 External Interface Write Switching Characteristics
        7. 5.9.6.7 External Interface Ready-on-Read Timing With One External Wait State
          1. Table 5-49 External Interface Read Switching Characteristics (Ready-on-Read, One Wait State)
          2. Table 5-50 External Interface Read Timing Requirements (Ready-on-Read, One Wait State)
          3. Table 5-51 Synchronous XREADY Timing Requirements (Ready-on-Read, One Wait State)
          4. Table 5-52 Asynchronous XREADY Timing Requirements (Ready-on-Read, One Wait State)
        8. 5.9.6.8 External Interface Ready-on-Write Timing With One External Wait State
          1. Table 5-53 External Interface Write Switching Characteristics (Ready-on-Write, One Wait State)
          2. Table 5-54 Synchronous XREADY Timing Requirements (Ready-on-Write, One Wait State)
          3. Table 5-55 Asynchronous XREADY Timing Requirements (Ready-on-Write, One Wait State)
        9. 5.9.6.9 XHOLD and XHOLDA Timing
          1. Table 5-56 XHOLD/XHOLDA Timing Requirements
  6. 6Detailed Description
    1. 6.1 Brief Descriptions
      1. 6.1.1  C28x CPU
      2. 6.1.2  Memory Bus (Harvard Bus Architecture)
      3. 6.1.3  Peripheral Bus
      4. 6.1.4  Real-Time JTAG and Analysis
      5. 6.1.5  External Interface (XINTF)
      6. 6.1.6  M0, M1 SARAMs
      7. 6.1.7  L0, L1, L2, L3, L4, L5, L6, L7, H0, H1, H2, H3, H4, H5 SARAMs
      8. 6.1.8  Boot ROM
      9. 6.1.9  Security
      10. 6.1.10 Peripheral Interrupt Expansion (PIE) Block
      11. 6.1.11 External Interrupts (XINT1–XINT7, XNMI)
      12. 6.1.12 Oscillator and PLL
      13. 6.1.13 Watchdog
      14. 6.1.14 Peripheral Clocking
      15. 6.1.15 Low-Power Modes
      16. 6.1.16 Peripheral Frames 0, 1, 2, 3 (PFn)
      17. 6.1.17 General-Purpose Input/Output (GPIO) Multiplexer
      18. 6.1.18 32-Bit CPU-Timers (0, 1, 2)
      19. 6.1.19 Control Peripherals
      20. 6.1.20 Serial Port Peripherals
    2. 6.2 Peripherals
      1. 6.2.1  DMA Overview
      2. 6.2.2  32-Bit CPU-Timer 0, CPU-Timer 1, CPU-Timer 2
      3. 6.2.3  Enhanced PWM Modules
      4. 6.2.4  High-Resolution PWM (HRPWM)
      5. 6.2.5  Enhanced CAP Modules
      6. 6.2.6  Enhanced QEP Modules
      7. 6.2.7  External ADC Interface
      8. 6.2.8  Multichannel Buffered Serial Port (McBSP) Module
      9. 6.2.9  Enhanced Controller Area Network (eCAN) Modules (eCAN-A and eCAN-B)
      10. 6.2.10 Serial Communications Interface (SCI) Modules (SCI-A, SCI-B, SCI-C)
      11. 6.2.11 Serial Peripheral Interface (SPI) Module (SPI-A, SPI-D)
      12. 6.2.12 Inter-Integrated Circuit (I2C)
      13. 6.2.13 GPIO MUX
      14. 6.2.14 External Interface (XINTF)
    3. 6.3 Memory Maps
    4. 6.4 Register Map
      1. 6.4.1 Device Emulation Registers
    5. 6.5 Interrupts
      1. 6.5.1 External Interrupts
    6. 6.6 System Control
      1. 6.6.1 OSC and PLL Block
        1. 6.6.1.1 External Reference Oscillator Clock Option
        2. 6.6.1.2 PLL-Based Clock Module
        3. 6.6.1.3 Loss of Input Clock
      2. 6.6.2 Watchdog Block
    7. 6.7 Low-Power Modes Block
  7. 7Applications, Implementation, and Layout
    1. 7.1 TI Design or Reference Design
  8. 8デバイスおよびドキュメントのサポート
    1. 8.1 はじめに
    2. 8.2 デバイスおよび開発ツールの項目表記
    3. 8.3 ツールとソフトウェア
    4. 8.4 ドキュメントのサポート
    5. 8.5 関連リンク
    6. 8.6 Community Resources
    7. 8.7 商標
    8. 8.8 静電気放電に関する注意事項
    9. 8.9 Glossary
  9. 9メカニカル、パッケージ、および注文情報
    1. 9.1 パッケージ情報

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • ZAY|179
サーマルパッド・メカニカル・データ
発注情報

6.2.8 Multichannel Buffered Serial Port (McBSP) Module

The McBSP module has the following features:

  • Compatible to McBSP in TMS320C54x/TMS320C55x DSP devices
  • Full-duplex communication
  • Double-buffered data registers that allow a continuous data stream
  • Independent framing and clocking for receive and transmit
  • External shift clock generation or an internal programmable frequency shift clock
  • A wide selection of data sizes including 8, 12, 16, 20, 24, or 32 bits
  • 8-bit data transfers with LSB or MSB first
  • Programmable polarity for both frame synchronization and data clocks
  • Highly programmable internal clock and frame generation
  • Direct interface to industry-standard CODECs, Analog Interface Chips (AICs), and other serially connected A/D and D/A devices
  • Works with SPI-compatible devices
  • The following application interfaces can be supported on the McBSP:
    • T1/E1 framers
    • IOM-2 compliant devices
    • AC97-compliant devices (the necessary multiphase frame synchronization capability is provided.)
    • IIS-compliant devices
    • SPI
  • McBSP clock rate,
    • TMS320C28346 TMS320C28345 TMS320C28344 TMS320C28343 TMS320C28342 TMS320C28341 q1_prs439.gif

    where CLKSRG source could be LSPCLK, CLKX, or CLKR. Serial port performance is limited by I/O buffer switching speed. Internal prescalers must be adjusted such that the peripheral speed is less than the I/O buffer speed limit.

NOTE

See Section 5 for maximum I/O pin toggling speed.

Figure 6-9 shows the block diagram of the McBSP module.

TMS320C28346 TMS320C28345 TMS320C28344 TMS320C28343 TMS320C28342 TMS320C28341 mcbsp_fbd_prufb7.gifFigure 6-9 McBSP Module

Table 6-8 provides a summary of the McBSP registers.

Table 6-8 McBSP Register Summary

NAME McBSP-A ADDRESS McBSP-B ADDRESS TYPE RESET VALUE DESCRIPTION
Data Registers, Receive, Transmit
DRR2 0x5000 0x5040 R 0x0000 McBSP Data Receive Register 2
DRR1 0x5001 0x5041 R 0x0000 McBSP Data Receive Register 1
DXR2 0x5002 0x5042 W 0x0000 McBSP Data Transmit Register 2
DXR1 0x5003 0x5043 W 0x0000 McBSP Data Transmit Register 1
McBSP Control Registers
SPCR2 0x5004 0x5044 R/W 0x0000 McBSP Serial Port Control Register 2
SPCR1 0x5005 0x5045 R/W 0x0000 McBSP Serial Port Control Register 1
RCR2 0x5006 0x5046 R/W 0x0000 McBSP Receive Control Register 2
RCR1 0x5007 0x5047 R/W 0x0000 McBSP Receive Control Register 1
XCR2 0x5008 0x5048 R/W 0x0000 McBSP Transmit Control Register 2
XCR1 0x5009 0x5049 R/W 0x0000 McBSP Transmit Control Register 1
SRGR2 0x500A 0x504A R/W 0x0000 McBSP Sample Rate Generator Register 2
SRGR1 0x500B 0x504B R/W 0x0000 McBSP Sample Rate Generator Register 1
Multichannel Control Registers
MCR2 0x500C 0x504C R/W 0x0000 McBSP Multichannel Register 2
MCR1 0x500D 0x504D R/W 0x0000 McBSP Multichannel Register 1
RCERA 0x500E 0x504E R/W 0x0000 McBSP Receive Channel Enable Register Partition A
RCERB 0x500F 0x504F R/W 0x0000 McBSP Receive Channel Enable Register Partition B
XCERA 0x5010 0x5050 R/W 0x0000 McBSP Transmit Channel Enable Register Partition A
XCERB 0x5011 0x5051 R/W 0x0000 McBSP Transmit Channel Enable Register Partition B
PCR 0x5012 0x5052 R/W 0x0000 McBSP Pin Control Register
RCERC 0x5013 0x5053 R/W 0x0000 McBSP Receive Channel Enable Register Partition C
RCERD 0x5014 0x5054 R/W 0x0000 McBSP Receive Channel Enable Register Partition D
XCERC 0x5015 0x5055 R/W 0x0000 McBSP Transmit Channel Enable Register Partition C
XCERD 0x5016 0x5056 R/W 0x0000 McBSP Transmit Channel Enable Register Partition D
RCERE 0x5017 0x5057 R/W 0x0000 McBSP Receive Channel Enable Register Partition E
RCERF 0x5018 0x5058 R/W 0x0000 McBSP Receive Channel Enable Register Partition F
XCERE 0x5019 0x5059 R/W 0x0000 McBSP Transmit Channel Enable Register Partition E
XCERF 0x501A 0x505A R/W 0x0000 McBSP Transmit Channel Enable Register Partition F
RCERG 0x501B 0x505B R/W 0x0000 McBSP Receive Channel Enable Register Partition G
RCERH 0x501C 0x505C R/W 0x0000 McBSP Receive Channel Enable Register Partition H
XCERG 0x501D 0x505D R/W 0x0000 McBSP Transmit Channel Enable Register Partition G
XCERH 0x501E 0x505E R/W 0x0000 McBSP Transmit Channel Enable Register Partition H
MFFINT 0x5023 0x5063 R/W 0x0000 McBSP Interrupt Enable Register
MFFST 0x5024 0x5064 R/W 0x0000 McBSP Pin Status Register