JAJSM93B june   2022  – may 2023 TPS1641

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Enable and Shutdown Input (EN/SHDN)
      2. 8.3.2  Overvoltage Protection (OVP)
      3. 8.3.3  Output Slew Rate and Inrush Current Control (dVdt)
      4. 8.3.4  Active Current Limiting (ILIM) With the TPS16412, TPS16413, TPS16416, and TPS16417
      5. 8.3.5  Active Power Limiting (PLIM) With the TPS16410, TPS16411, TPS16414, and TPS16415
        1. 8.3.5.1 Internal Current Limit for the TPS16410 and TPS16411
      6. 8.3.6  Overcurrent Protection (IOCP) and Blanking Time (IDLY or PDLY) for Transient Loads
      7. 8.3.7  Fast-Trip and Short-Circuit Protection
      8. 8.3.8  Analog Load Current Monitor (IMON) on the IOCP Pin
      9. 8.3.9  IN to OUT Short Detection (TPS16410, TPS16411, TPS16412, and TPS16413)
      10. 8.3.10 Thermal Shutdown and Overtemperature Protection
      11. 8.3.11 Fault Response and Indication (FLT)
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application: 15-W Power Limiting for Low Power Circuits (LPCs)
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Setting Overvoltage Setpoints
        2. 9.2.2.2 Setting the Output Overcurrent Setpoint (IOCP)
        3. 9.2.2.3 Setting the Output Power Limit
        4. 9.2.2.4 Monitoring the Output Current
        5. 9.2.2.5 Limiting the Inrush Current and Setting the Output Slew Rate
      3. 9.2.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 Accurate Power or Current Limiting at the Output of DC/DC or Flyback Converter
    4. 9.4 Best Design Practices
    5. 9.5 Power Supply Recommendations
      1. 9.5.1 Transient Protection
    6. 9.6 Layout
      1. 9.6.1 Layout Guidelines
      2. 9.6.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 ドキュメントの更新通知を受け取る方法
    2. 10.2 サポート・リソース
    3. 10.3 Trademarks
    4. 10.4 静電気放電に関する注意事項
    5. 10.5 用語集
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Vcc, FLT Input Voltage –0.3 67 V
OVP Input Voltage –0.3 62 V
IN, IN-OUT, IOCP Input Voltage –0.3 42 V
OUT Input Voltage –1 42 V
EN/SHDN, PDLY/IDLY Input Voltage –0.3 5.5 V
dVdT, PLIM/ILIM Input Voltage –0.3 5.5 V
IIOCP,IPDLY,IPLIM, IdVdT, IILIM Source Current Internally Limited
TJ Junction temperature –40 150 °C
Transient Junction Temperature –40 TTSD °C
Tstg Storage temperature –65 150 °C
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.