JAJSNB7 march   2023 TPS548C26

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 説明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 絶対最大定格
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Internal VCC LDO and Using an External Bias on VCC and VDRV Pin
      2. 7.3.2  Input Undervoltage Lockout (UVLO)
        1. 7.3.2.1 Fixed VCC_OK UVLO
        2. 7.3.2.2 Fixed VDRV UVLO
        3. 7.3.2.3 Fixed PVIN UVLO
        4. 7.3.2.4 Enable
      3. 7.3.3  Set the Output Voltage
      4. 7.3.4  Differential Remote Sense and Feedback Divider
      5. 7.3.5  Start-up and Shutdown
      6. 7.3.6  Loop Compensation
      7. 7.3.7  Set Switching Frequency and Operation Mode
      8. 7.3.8  Switching Node (SW)
      9. 7.3.9  Overcurrent Limit and Low-side Current Sense
      10. 7.3.10 Negative Overcurrent Limit
      11. 7.3.11 Zero-Crossing Detection
      12. 7.3.12 Input Overvoltage Protection
      13. 7.3.13 Output Undervoltage and Overvoltage Protection
      14. 7.3.14 Overtemperature Protection
      15. 7.3.15 Power Good
    4. 7.4 Device Functional Modes
      1. 7.4.1 Forced Continuous-Conduction Mode
      2. 7.4.2 Auto-Skip Eco-mode Light Load Operation
      3. 7.4.3 Powering the Device from a 12-V Bus
      4. 7.4.4 Powering the Device From a Split-rail Configuration
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC and VRDV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 PG Pullup Resistor Selection
      4. 8.2.4 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
        1. 8.4.2.1 Thermal Performance on TPS548C26 Evaluation Board
  9. 9 Device and Documentation Support
    1. 9.1 ドキュメントの更新通知を受け取る方法
    2. 9.2 サポート・リソース
    3. 9.3 Trademarks
    4. 9.4 静電気放電に関する注意事項
    5. 9.5 用語集
  10. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.2.3.6 PG Pullup Resistor Selection

The PG output is an open-drain output and must be pulled up externally through a pullup resistor. Place a pullup resistor, within a 1-kΩ to 100-kΩ range, at the PG pin (pin 2). In this example, PG is pulled up to VCC/VDRV with a 10-kΩ resistor.