JAJSRV1 データシート

JAJSRV1 June 2024 TPS562243 , TPS562246

PRODUCTION DATA

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）

DRL|6
- MPDS159H

サーマルパッド・メカニカル・データ

発注情報

jajsrv1_oa

7.2.2.3 Output Filter Selection

The LC filter used as the output filter has a double pole at Equation 4. In this equation, C_OUT must use effective value after derating, not nominal value.

Equation 4.

{F r e q u e n c y}_{d o u b l e p o l e} = \frac{1}{2 \times π \times \sqrt{L_{O U T} \times C_{O U T}}}

For any control topology that is compensated internally, there is a range of the output filter that the control topology can support. At low frequency, the overall loop gain is set by the output set point resistor divider network and the internal gain of the device. The low frequency phase is 180°. At the output filter pole frequency, the gain rolls off with a rate of –40dB per decade and the phase has a 180 degree drop. The internal ripple generation network introduces a high-frequency zero that reduces the gain roll off from –40dB to –20dB per decade and leads to the 90 degree phase boost. The high frequency zero brought by the internal ripple injection circuit is about 160kHz. TI recommends the double pole frequency brought by the selected inductor and capacitor to be located at about 40kHz, so that the phase boost provided by this high frequency zero provides adequate phase margin for the stability requirement. For output voltage higher than 2V, TI suggests to add a C_FF capacitor to increase the bandwidth and the phase margin. The C_FF range suggested is from 10pF to 100pF. The crossover frequency of the overall system must usually be targeted to be less than one-third of the switching frequency.

Table 7-2 Recommended Component Values

OUTPUT VOLTAGE (V)	L_OUT (uH)	C_OUT(uF)	C_OUT(uF) ⁽¹⁾ Range	R_FBT (kΩ)	R_FBB (kΩ)	C_FF(pF)
0.6	1	22 (10V Rated)	20-90	0	10.0	-
1.05	1.2	22 (10V Rated)	10-45	7.5	10.0	-
3.3	3.3	22 (25V Rated)	15-60	135.0	30.0	47
5	3.3	22 (25V Rated)	15-60	220.0	30.0	47
7	3.3	22x2 (25V Rated)	15-60	320.0	30.0	47

(1) A ceramic capacitor is used in this table. All the C_OUT values are after derating.

The inductor peak-to-peak ripple current, peak current and RMS current are calculated using Equation 5, Equation 6, and Equation 7. The inductor saturation current rating must be greater than the calculated peak current and the RMS or heating current rating must be greater than the calculated RMS current.

Equation 5.

I_{P - P} = \frac{V_{O U T}}{V_{I N (M a x)}} \times \frac{V_{I N (M a x)} - V_{O U T}}{L_{O U T} \times f_{S W}}

Equation 6.

I_{P E A K} = I_{O} + \frac{I_{P - P}}{2}

Equation 7.

I_{L O (R M S)} = \sqrt{I_{O}^{2} + \frac{1}{12} \times I_{P - P}^{2}}

For this design example, the calculated peak current is 2.32A and the calculated RMS current is 2.01A. The inductor used is WE 74438357012.

The capacitor value and ESR determines the amount of output voltage ripple. The TPS56224x is intended for use with ceramic or other low ESR capacitors. TI recommends to use 1× 22µF output cap. Use Equation 8 to determine the required RMS current rating for the output capacitor.

Equation 8.

I_{C O (R M S)} = \frac{V_{O U T} \times (V_{I N} - V_{O U T})}{\sqrt{12} \times V_{I N} \times L_{O U T} \times f_{S W}}

For this design, one MuRata GRM21BR61A226ME44L 22µF output capacitor can be used. The typical ESR is 2mΩ each. The calculated RMS current is 0.2A and each output capacitor is rated for 4A.