JAJSI75A April   2018  – November 2019 TPS57112C-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      概略回路図
      2.      効率と出力電流との関係
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Switching Characteristics
    8. 7.8 Typical Characteristics Curves
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Fixed-Frequency PWM Control
      2. 8.3.2 Slope Compensation and Output Current
      3. 8.3.3 Bootstrap Voltage (BOOT) and Low-Dropout Operation
        1. 8.3.3.1 Error Amplifier
      4. 8.3.4 Voltage Reference
    4. 8.4 Device Functional Modes
      1. 8.4.1  Adjusting the Output Voltage
      2. 8.4.2  Enable Functionality and Adjusting Undervoltage Lockout
      3. 8.4.3  Slow-Start or Tracking Pin
      4. 8.4.4  Sequencing
      5. 8.4.5  Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
      6. 8.4.6  Overcurrent Protection
      7. 8.4.7  Frequency Shift
      8. 8.4.8  Reverse Overcurrent Protection
      9. 8.4.9  Synchronize Using the RT/CLK Pin
      10. 8.4.10 Power Good (PWRGD Pin)
      11. 8.4.11 Overvoltage Transient Protection
      12. 8.4.12 Thermal Shutdown
      13. 8.4.13 Small-Signal Model for Loop Response
      14. 8.4.14 Simple Small-Signal Model for Peak-Current-Mode Control
      15. 8.4.15 Small-Signal Model for Frequency Compensation
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Selecting the Switching Frequency
        2. 9.2.2.2 Output Inductor Selection
        3. 9.2.2.3 Output Capacitor
        4. 9.2.2.4 Input Capacitor
        5. 9.2.2.5 Slow-Start Capacitor
        6. 9.2.2.6 Bootstrap Capacitor Selection
        7. 9.2.2.7 Output Voltage and Feedback Resistor Selection
        8. 9.2.2.8 Compensation
        9. 9.2.2.9 Power-Dissipation Estimate
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デベロッパー・ネットワークの製品に関する免責事項
      2. 12.1.2 開発サポート
    2. 12.2 ドキュメントのサポート
      1. 12.2.1 関連資料
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 サポート・リソース
    5. 12.5 商標
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6 Pin Configuration and Functions

RTE Package
16-Pin WQFN With Thermal Pad
Top View
TPS57112C-Q1 po_RTE-16_SLVSAL8.gif

Pin Functions

PIN I/O DESCRIPTION
NAME NO.
AGND 5 — Connect analog ground electrically to GND close to the device.
BOOT 13 O There is a requirement for a bootstrap capacitor between BOOT and PH. A voltage on this capacitor that is below the minimum required by the BOOT UVLO forces the output to switch off until the capacitor recharges.
COMP 7 O Error amplifier output, and input to the output-switch current comparator. Connect frequency-compensation components to this pin.
EN 15 I Enable pin, internal pullup current source. Pull below 1.2 V to disable. Float to enable. One can use this pin to set the on-off threshold (adjust UVLO) with two additional resistors.
GND 3 — Power ground. Connect this pin electrically to the thermal pad directly under the IC.
4
PH 10 O The source of the internal high-side power MOSFET, and drain of the internal low-side (synchronous) rectifier MOSFET.
11
12
PWRGD 14 O An open-drain output; asserts low if output voltage is low due to thermal shutdown, overcurrent, overvoltage, undervoltage, or EN shutdown.
RT/CLK 8 I Resistor-timing or external-clock input pin
SS/TR 9 I Slow-start and tracking. An external capacitor connected to this pin sets the output-voltage rise time.
Another use of this pin is for tracking.
VIN 1 I Input supply voltage, 2.95 V to 6 V.
2
16
VSENSE 6 I Inverting node of the transconductance (gm) error amplifier
Thermal pad — Connect the GND pin to the exposed thermal pad for proper operation. Connect this thermal pad to any internal PCB ground plane using multiple vias for good thermal performance.