SLVSA48A April   2010  – September 2015 TPS65200

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Data Transmission Timing
    7. 6.7 Typical Characteristics
      1. 6.7.1 Switching Charger
      2. 6.7.2 OTG Boost
      3. 6.7.3 LDO
      4. 6.7.4 WLED Boost
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Global State Diagram
      2. 7.3.2 LED Driver Operation
        1. 7.3.2.1 Undervoltage Lockout
        2. 7.3.2.2 Shutdown
        3. 7.3.2.3 Soft-Start Circuit
        4. 7.3.2.4 Open LED Protection
        5. 7.3.2.5 Current Program
        6. 7.3.2.6 Brightness Dimming
        7. 7.3.2.7 Inductor Overcurrent Protection
      3. 7.3.3 HV LDO
      4. 7.3.4 Interrupt Pin
      5. 7.3.5 Current Shunt Monitor
    4. 7.4 Device Functional Modes
      1. 7.4.1 Charge Mode Operation
        1. 7.4.1.1  Input Current Limiting and D+/D- Detection
        2. 7.4.1.2  Bad Adaptor Detection/Rejection (CHBADI)
        3. 7.4.1.3  Input Current Limiting at Start-Up
        4. 7.4.1.4  Charge Profile
        5. 7.4.1.5  Precharge to Fast Charge Threshold (VSHORT)
        6. 7.4.1.6  PWM Controller in Charge Mode
        7. 7.4.1.7  Battery Charging Process
        8. 7.4.1.8  Thermal Regulation and Protection
        9. 7.4.1.9  Safety Timer in Charge and Boost Mode (CH32MI, BST32SI)
        10. 7.4.1.10 Input Voltage Protection in Charge Mode
          1. 7.4.1.10.1 Input Overvoltage Protection (VBUSOVPI)
          2. 7.4.1.10.2 Reverse Current Protection (CHRVPI)
          3. 7.4.1.10.3 Input Voltage Based Dynamic Power Management (CHDPMI)
        11. 7.4.1.11 Battery Protection in Charge Mode
          1. 7.4.1.11.1 Battery Charge Current Limiting
          2. 7.4.1.11.2 Output Overvoltage Protection (CHBATOVPI)
          3. 7.4.1.11.3 Battery Short Protection
        12. 7.4.1.12 Charge Status Output, STAT Pin
      2. 7.4.2 Boost Mode Operation
        1. 7.4.2.1 PWM Controller in Boost Mode
        2. 7.4.2.2 Boost Start Up
        3. 7.4.2.3 PFM Mode at Light Load
        4. 7.4.2.4 Safety Timer in Boost Mode (BST32SI)
        5. 7.4.2.5 Protection in Boost Mode
          1. 7.4.2.5.1 Output Overvoltage Protection (BSTBUSOVI)
          2. 7.4.2.5.2 Output Over-Load Protection (BSTOLI)
          3. 7.4.2.5.3 Battery Voltage Protection (BSTLOWVI, BSTBATOVI)
      3. 7.4.3 High Impedance Mode
    5. 7.5 Programming
      1. 7.5.1 I2C Bus Operation
    6. 7.6 Register Maps
      1. 7.6.1  Control Register (CONTROL)
      2. 7.6.2  Charger Config Register A (CONFIG_A)
      3. 7.6.3  Charger Config Register B (CONFIG_B)
      4. 7.6.4  Charger Config Register C (CONFIG_C)
      5. 7.6.5  Charger Config Register D (CONFIG_D)
      6. 7.6.6  WLED Control Register (WLED)
      7. 7.6.7  Status Register A (STATUS_A)
      8. 7.6.8  Status Register B (STATUS_B)
      9. 7.6.9  Interrupt Register 1 (INT1)
      10. 7.6.10 Interrupt Register 2 (INT2)
      11. 7.6.11 Interrupt Register 3 (INT3)
      12. 7.6.12 Interrupt Mask Register 1 (MASK1)
      13. 7.6.13 Interrupt Mask Register 2 (MASK2)
      14. 7.6.14 Interrupt Mask Register 3 (MASK3)
      15. 7.6.15 Chip ID Register (CHIPID)
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Community Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9 Power Supply Recommendations

This device should be connected to a single cell Li+ battery or to a 5-V VBUS supply. The current required from VBUS will depend on the desired limit, maximum of 1.55 A.