JAJSN89A December   2021  – March 2022 TPS92624-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Power Supply (SUPPLY)
        1. 7.3.1.1 Power-On Reset (POR)
        2. 7.3.1.2 Suppply Current in Fault Mode
      2. 7.3.2  Enable and Shutdown
      3. 7.3.3  Constant-Current Output and Setting (INx)
      4. 7.3.4  Thermal Sharing Resistor (OUTx and RESx)
      5. 7.3.5  PWM Control (PWMx)
      6. 7.3.6  Supply Control
      7. 7.3.7  Diagnostics
        1. 7.3.7.1 LED Short-to-GND Detection
        2. 7.3.7.2 LED Open-Circuit Detection
        3. 7.3.7.3 LED Open-Circuit Detection Enable (DIAGEN)
        4. 7.3.7.4 Overtemperature Protection
        5. 7.3.7.5 Low Dropout Operation
      8. 7.3.8  FAULT Bus Output With One-Fails-All-Fail
      9. 7.3.9  FAULT Table
      10. 7.3.10 LED Fault Summary
      11. 7.3.11 IO Pins Inner Connection
    4. 7.4 Device Functional Modes
      1. 7.4.1 Undervoltage Lockout, V(SUPPLY) < V(POR_rising)
      2. 7.4.2 Normal Operation V(SUPPLY) ≥ 4.5 V
      3. 7.4.3 Low-Voltage Dropout Operation
      4. 7.4.4 Fault Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 BCM Controlled Rear Lamp With One-Fails-All-Fail Setup
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Independent PWM Controlled Rear Lamp By MCU
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 サポート・リソース
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.9 FAULT Table

Table 7-1 Fault Table With DIAGEN = HIGH (Full Function)
FAULT BUS STATUSFAULT TYPEDETECTION MECHANISMCONTROL INPUTDEGLITCH TIMEFAULT BUSFAULT HANDLING ROUTINEFAULT RECOVERY
FAULT = HOpen-circuit or short-to-supplyV(IN) – V(OUT) < V(OPEN_th_rising) PWMx = Ht(OPEN_deg)Constant-current pulldownDevice turns failed output off and retries with constant current I(retry), ignoring the PWM input.Auto recovery
Short-to-groundV(OUT) < V(SG_th_falling)
OR
V(RES) < V(SG_th_falling)		 PWMx = Ht(SG_deg)Constant-current pulldownDevice turns failed output off and retries with constant current I(retry), ignoring the PWM input.Auto recovery
OvertemperatureTJ > T(TSD)t(TSD_deg)Constant-current pulldownDevice turns all output channels off.Auto recovery
FAULT = L Fault is detected Device turns all remained channels off and keeps retry on the failed channels. After the Fault pin is released, all channels are turned on after t(FAULT_recovery) time.
No fault is detected Device turns all output channels off.
Table 7-2 Fault Table With DIAGEN = LOW (Full Function)
FAULT BUS STATUSFAULT TYPEDETECTION MECHANISMCURRENT OUTPUTDEGLITCH TIMEFAULT BUSFAULT HANDLING ROUTINEFAULT RECOVERY
FAULT = HOpen-circuit or short-to-supplyIgnored
Short-to-groundV(OUT) < V(SG_th_falling)
OR
V(OUT) < V(SG_th_falling)		PWMx = Ht(SG_deg)Constant-current pulldownDevice turns output off and retries with constant current I(retry), ignoring the PWM input.Auto recovery
OvertemperatureTJ > T(TSD)t(TSD_deg)Constant-current pulldownDevice turns all output channels off.Auto recovery
FAULT = L Fault is detected Device turns all remained channels off and keeps retry on the failed channels. After the Fault pin is released, all channels are turned on after t(FAULT_recovery) time.
No fault is detected Device turns all output channels off.