JAJSUW9A June   2024  – September 2024 TXS0102V-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Switching Characteristics, VCCA = 1.8 ± 0.15 V
    7. 5.7  Switching Characteristics, VCCA = 2.5 ± 0.2 V
    8. 5.8  Switching Characteristics, VCCA = 3.3 ± 0.3 V
    9. 5.9  Switching Characteristics: Tsk, TMAX
    10. 5.10 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Architecture
      2. 7.3.2 Input Driver Requirements
      3. 7.3.3 Output Load Considerations
      4. 7.3.4 Enable and Disable
      5. 7.3.5 Pullup or Pulldown Resistors on I/O Lines
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • DCU|8
サーマルパッド・メカニカル・データ
発注情報

6 Parameter Measurement Information

Unless otherwise noted, all input pulses are supplied by generators having the following characteristics:

  • PRR 10MHz
  • ZO = 50 W
  • dv/dt ≥ 1V/ns

Note: All parameters and waveforms are not applicable to all devices.
TXS0102V-Q1 Data Rate, Pulse Duration, Propagation Delay, Output Rise And Fall Time Measurement Using A Push-Pull DriverFigure 6-1 Data Rate, Pulse Duration, Propagation Delay, Output Rise
And Fall Time Measurement Using A Push-Pull Driver
TXS0102V-Q1 Data Rate, Pulse Duration, Propagation Delay, Output Rise And Fall Time Measurement Using An Open-Drain DriverFigure 6-2 Data Rate, Pulse Duration, Propagation Delay, Output Rise
And Fall Time Measurement Using An Open-Drain Driver
TXS0102V-Q1 Load Circuit For Enable / Disable Time MeasurementFigure 6-3 Load Circuit For Enable / Disable Time Measurement
Table 6-1 Switch Configuration For Enable / Disable Timing
TESTS1
tPZL(2), tPLZ(1)2 × VCCO
tPHZ(1), tPZH(2)Open
(1) tPLZ and tPHZ are the same as tdis.
(2) tPZL and tPZH are the same as ten.
TXS0102V-Q1 Voltage Waveforms Pulse Duration
(1) All input pulses are measured one at a time, with one transition per measurement.
Figure 6-4 Voltage Waveforms Pulse Duration
TXS0102V-Q1 Voltage Waveforms Propagation Delay Times
(1) All input pulses are measured one at a time, with one transition per measurement.
Figure 6-5 Voltage Waveforms Propagation Delay Times
TXS0102V-Q1 Voltage Waveforms Enable And Disable Times
(1) Waveform 1 is for an output with internal conditions so that the output is low, except when disabled by the output control.
(2) Waveform 2 is for an output with internal conditions so that the output is high, except when disabled by the output control.
Figure 6-6 Voltage Waveforms Enable And Disable Times